brake light Alfa Romeo 147 2005 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
15
If the ignition device is
tampered with (for exam-
ple an attempted theft)
have it checked over by Alfa
Romeo Authorised Services before
travelling again.
STEERING LOCK
Engaging:
– move the key to STOPorPARK, then
remove the key and turn the steering wheel
slightly to facilitate the locking action.
Disengaging:
– turn the key to MARgently rocking the
steering wheel from side to side.
DOORS
OPENING/CLOSING FROM
OUTSIDE
To open the driver's door turn the key
clockwise and to open the passengers' door,
optional for versions/markets where ap-
plicable, turn the key anti-clockwise, then
remove the key and press the button (A-
fig. 9).
To close the door, turn the key in the lock
in the opposite direction to the one for open-
ing.
fig. 9
A0A0017m
Before opening a door, al-
ways make sure that it can
be done safely.
WARNING
Never remove the ignition
key with the car on the
move. The steering wheel would
lock automatically the first time the
steering wheel is turned. This al-
so occurs if the car is towed.
WARNING
When leaving the vehicle
always remove the key
from the ignition to prevent any oc-
cupants of the vehicle from acci-
dentally activating the controls.
Never leave children in the vehi-
cle unaccompanied. Remember to
engage the handbrake, and, if the
vehicle is parked on an uphill slope,
to engage first gear. If the vehicle
is facing downhill, engage reverse
gear.
WARNING
It is absolutely forbidden to
carry out whatever after-
market operation involving steering
system or steering column modifi-
cations (e.g.: installation of anti-
theft device) that could badly affect
performance and safety, cause the
lapse of warranty and also result in
non-compliance of the car with ho-
mologation requirements.
WARNING

GETTING TO KNOW YOUR CAR
47
The device is disengaged automatically in
any one of the following cases:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR or VDC, MSR system cuts in.
CONTROLS(fig. 65)
Cruise Control is controlled by the
ON/OFFknurled ring (A), by the +/–
ring (B) and by the RESbutton (C).
Ring (A) has two positions:
–OFFin this position the device is deac-
tivated;
–ONis the normal operating position of
the device. When the knurled ring (A) is
in this position, the warning light
Üon the
instrument cluster turns on.Ring (B) serves for memorising and main-
taining the car speed or for increasing or low-
ering the speed memorised.
Turn the ring (B) to (+) to memorise the
speed reached or increase the speed mem-
orised.
Turn the ring (B) to (–) to lower the speed
memorised.
Each time the ring is actuated (B) the speed
increases or lowers by about 1.5 km/h.
Keeping the ring turned the speed changes
continuously. The new speed reached will
be maintained automatically.
TheRESbutton (C) resets the memorised
speed.
IMPORTANTTurning the ignition key to
STOPor the ring (A) to OFF, the speed
memorised is cleared and the system is
switched off.
CRUISE CONTROL
GENERAL
The speed regulator (CRUISE CON-
TROL), with electronic control, makes it
possible to drive the car at the required
speed without pressing the accelerator ped-
al. This reduces driving fatigue during long
journeys because the speed memorised is
automatically maintained.
IMPORTANTThe device can only be en-
gaged at speeds above 30 km/h.
fig. 65
A0A0077m
Cruise control must be ac-
tivated only when the
route and traffic allow a constant
speed for a sufficiently long dis-
tance completely safely.
WARNING

GETTING TO KNOW YOUR CAR
48
TO MEMORISE THE SPEED
Move the ring (A) to ONand take the car
to the required speed normally. Turn the ring
(B) to (+) for at least three seconds, then
release it. The car speed is memorised and
it is therefore possible to release the accel-
erator pedal.
The car will continue to travel at the mem-
orised constant speed until one of the fol-
lowing conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR or VDC system cuts in.
IMPORTANTIn the case of need (when
overtaking for instance) acceleration is pos-
sible simply pressing the accelerator pedal;
later, releasing the accelerator pedal, the car
will return to the speed memorised previ-
ously.
TO RESET
THE MEMORISED SPEED
If the device has been disengaged for ex-
ample pressing the brake or clutch pedal,
the memorised speed can be reset as fol-
lows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time of
speed memorising (4th, 5th or 6th speed);
– press the RESbutton (C).
TO INCREASE
THE MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then mem-
orising the new speed reached (turning the
ring (B) for more than three seconds);
or
2) momentaneously turning the ring (B) to
(+): each pulse of the ring will correspond to
a slight increase in speed (about 1.5 km/h)
while pressing continuously will correspond
to a continuous speed increase. Releasing the
ring (B) the new speed will be memorised
automatically.

GETTING TO KNOW YOUR CAR
77
Warning
light on dialMessage
on display
WARNING LIGHTS
IMPORTANTThe presence of warning lights depends on the type of equipment with which the car is fitted.
x
LOW BRAKE FLUID AND/OR HANDBRAKE ON
Turning the ignition key to MARthe warning light on the dial turns on, but it should go off after
approx. 4 seconds.
The warning light turns on when the level of the brake fluid in the reservoir falls below the mini-
mum level, due to a possible leak in the circuit and when the handbrake is engaged.
u
HIGH ENGINE COOLANT FLUID TEMPERATURE
Turning the ignition key to MARthe warning light on the dial turns on, but it should go off after
approx. 4 seconds.
The warning light turns on together with the message + symbol on the reconfigurable multifunc-
tion display, when the engine is overheated. If it turns on when travelling, stop the car leaving the
engine on and slightly accelerated to further activate the circulation of the coolant fluid.
If the warning light does not go off within the next 2 or 3 minutes, stop the engine and contact
Alfa Romeo Authorised Services.
If the xwarning light turns on when travelling check that the hand-
brake is not engaged. If the warning light stays on together with the
message + symbol on the reconfigurable multifunction display with the hand-
brake off, stop the car immediately and contact Alfa Romeo Authorised Services.
WARNING

GETTING TO KNOW YOUR CAR
80
Warning
light on dialMessage
on display
BRAKE PAD WEAR
The message + symbol are shown on the reconfigurable multifunction display when the front brake
pads are worn; in this case have them changed as soon as possible.
IMPORTANTAs the car is fitted with wear sensors for the front brake pads, when changing them,
also check the rear brake pads.
SELESPEED GEARBOX FAILURE
The message + symbol are shown by the reconfigurable multifunction display when a fault to Se-
lespeed gearbox is detected.
If warning light tand the message appear on the display, contact Al-
fa Romeo Authorised Services as soon as possible to have the fault eli-
minated.
WARNING

GETTING TO KNOW YOUR CAR
108
HAND BRAKE (fig. 94)
The hand brake lever is located between
the two front seats.
To operate the brake when the vehicle is
stationary, pull lever (A) upwards, until the
required braking action is obtained.
When the ignition key is at MARthe
warning light on the instrument cluster
x
will come on.
fig. 94
A0A0490m
The display (B), in the tachometer shows
the positions during adjustment.
For correct adjustment, bear in mind the
following conditions:
– position 0: one or two people occupy-
ing the front seats
– position 1: five people;
– position 2: five people + load in the
boot;
– position 3: driver + maximum permis-
sible load all stowed in lug-
gage compartment
fig. 93
A0A0467m
HEADLIGHT AIMING DEVICE
(fig. 93)(excluding versions
with Xenon headlights)
The headlights should be aimed correctly
depending on the vehicle load.
To do this, use the rocker button (A), on
the plate at the side of the steering column:
– press the arrow on the button (
A), to
increase by one position (eg.: 0
➟1➟ 2
➟3);
– press the arrow on the button (
S), to
lower by one position (eg.: 3
➟2➟1
➟0).
Adjust the beams every time
the load carried changes.
WARNING
The wheels should be
locked after a few clicks of
the hand brake. If this does not oc-
cur contact Alfa Romeo Authorised
services to have the hand brake
adjusted.
WARNING

GETTING TO KNOW YOUR CAR
109
To release the hand brake:
– slightly lift the lever (A) and press the
release button (B);
– keeping the button pressed lower the
lever, the warning light
xon the instru-
ment cluster will go out.
To prevent the car from moving acciden-
tally, keep the brake pedal pressed when
engaging the hand brake.
IMPORTANTThe hand brake lever (A)
is fitted with a safety device which prevents
the brake from being released when, with
the lever pulled, button (B) is pressed.
Therefore, to release the brake, in addition
to pressing button (B) it is also necessary
to pull lever (A) further upwards to release
the safety device, then lower the lever com-
pletely.
IMPORTANTOn certain versions a
buzzer sounds to alert the driver if the car
is moved with the hand brake engaged.
GEARSHIFT LEVER (fig. 95)
The position of the single gears is shown
by the pictogram on the gearshift lever
knob.
When shifting gear, always fully depress
the clutch pedal. Before engaging reverse
gear (R) wait for the car to be stationary.
For versions fitted with six speed gearbox,
to engage reverse gear (R), raise the ring
under the grip (with the fingers of the same
hand holding the lever).
After engaging reverse gear, release the
ring. It is not necessary to raise the ring on
the lever when shifting from reverse to an-
other gear.
fig. 95
A0A0410m
To change gear smoothly,
the clutch pedal must be
fully depressed. Therefore, there
should be no obstacles on the floor
under the pedal unit: make sure
that any mats are well laid and do
not interfere with the pedals.
WARNING
IMPORTANTReverse gear may only be
engaged with the car completely at a stand-
still. With the engine running, before en-
gaging reverse gear it is necessary to wait
for at least 3 seconds with the clutch pedal
fully depressed to prevent clashing and the
possibility of damaging the gears.

GETTING TO KNOW YOUR CAR
113
STARTING THE ENGINE
The engine can be started either with a
gear engaged or in neutral (N) provided
that the brake pedal is fully depressed.
IMPORTANTIf the brake pedal is not
depressed, the starter motor will not turn,
thus preventing the engine from being start-
ed.
After starting, the gearbox sets to neutral
automatically, the reconfigurable multifunc-
tion display shows the letter (N) and the
system selects the semiautomatic operating
mode (manual).
SWITCHING OFF THE ENGINE
AND SYSTEM DEACTIVATION
Turning the ignition key to STOPthe en-
gine turns off but the Selespeed system is
still active waiting for the car to stop com-
pletely. After about 2 - 4 seconds from when
the key has been moved to STOP, the hy-
draulic part is deactivated and the reconfig-
urable multifunction display is turned off im-
mediately afterwards; at this point is the Se-
lespeed system deactivated.
The gear selected before switching off the
engine remains engaged.
If the engine is stopped with the gearbox
in neutral (N), the buzzer calls the driver’s
attention so that the car can be put in safe-
ty conditions engaging first gear (1) or re-
verse (R). In this case, the ignition key
should be turned to MARand with the
brake pedal pressed, engage first gear (1)
or reverse (R).
IMPORTANTIf the engine is stopped
with the CITYmode engaged, this will be
stored by the system. Indeed, the next time
the engine is started, this condition will still
be active.IMPORTANTShould the engine go off
with the car on the move, the next time it
is started the Alfa Romeo CODE warning
light (Y) may come on. In this case check
that the warning light goes off turning the
engine off and on again with the vehicle sta-
tionary. If not contact Alfa Romeo Authorised
Services.
NEVER leave the car with
the gears in neutral (N).
WARNING
Never remove the ignition
key when the car is mov-
ing. In addition to the fact that the
Selespeed system would not work
properly up to stopping the car, the
steering wheel would lock auto-
matically the first time it is turned.
WARNING
If the engine fails to start
with the gear engaged, the
driver is informed of the potential-
ly dangerous situation due to the
fact that the gearbox is in neutral
by the buzzer and by the reconfig-
urable multifunction display.
WARNING

GETTING TO KNOW YOUR CAR
117
In the “MANUAL” operating mode there
are certain automatic/security devices which
simplify driving:
– when slowing down the clutch is opened
and the transmission ratio is automatically
reduced to be ready for picking up again;
otherwise, when the car is stopped, the
gearbox will automatically be in firstgear
(1);
– requests to change gear that would take
the engine to above maximum speed or be-
low minimum speed are not accepted;
– if jamming occurs during gear engage-
ment, the system firstly tries to engage the
gear required again and, if it is still not pos-
sible, it automatically engages the imme-
diately higher one to avoid leaving the car
inneutral.
IMPORTANTIt is advisable to wait for
the end of a gear shifting operation before
requesting another one, to avoid multiple
requests in rapid succession.AUTOMATIC OPERATION (CITY)
The automatic operating mode CITYis se-
lected pressing button (A-fig. 106) at the
base of the gearshift lever.
In addition to the gear, the reconfigurable
multifunction display shows the word CITY
(fig. 99).
The system decides directly when gearshift-
ing according to the engine running speed
and the driving style.
Releasing the accelerator pedal quickly, the
system does not engage a higher gear in or-
der to maintain an adequate level of engine
brake.
FAILURE WARNING
Failures of the Selespeed gearbox are shown
by the
twarning light (fig. 100) con-
nected with the associated failure message,
both shown on the display.
When the system is turned on (turning the
ignition key to MAR), the warning light
should turn on glowing steadily for about
4 seconds and then turn off.If the warning light stays on it means that
a fault to the gearbox has been detected; at
the same time a buzzer sounds intermit-
tently for 4 seconds to attract the driver's
attention.
In the case of a fault to the gearshift con-
trol lever, the system automatically engages
the automatic operating mode CITYto
make it possible to reach the nearest Alfa
Romeo Authorised Service to have the fault
eliminated.
In the case of a fault to other gearbox com-
ponents, the system only allows the en-
gagement of certain gears: first gear (1),
second gear (2) and reverse (R).
If warning light tand
the message appear on the
display, contact Alfa Romeo Au-
thorised Services as soon as pos-
sible to have the fault eliminated.
WARNING

GETTING TO KNOW YOUR CAR
134
ABS
The car is fitted with an ABS braking sys-
tem, which prevents the wheels from lock-
ing when braking, makes full use of the grip
and within the limits of the grip available,
keeps the car controllable also in emergency
braking.
When braking a slight pulsing accompa-
nied by noise may be felt on the brake ped-
al due to the action of the ABS system.
This should not be interpreted as a brak-
ing malfunction. It is the signal to the driver
that the ABS has come into action: it is the
warning that the car is travelling at the lim-
it of its grip and therefore the speed should
be adapted to the type of road.
The ABS system is an additional part of the
base braking system; in the event of a fail-
ure it is disabled, leaving the braking sys-
tem in the same conditions as a vehicle with-
out ABS.
In the case of a failure, the anti-lock action
is no longer present, the braking capacity of
the vehicle is not adversely affected at all.If you have never previously used cars fit-
ted with ABS, it is advisable to practice a lit-
tle on a slippery surface, naturally in safe-
ty conditions and in accordance with the lo-
cal Highway Code you are also advised to
read the following instructions carefully.
The advantage of the ABS over a conven-
tional system is that it makes it possible to
obtain the highest degree of handling also
when braking completely under limited grip
conditions, preventing the wheels from lock-
ing.
However, with the ABS do not expect the
braking distance to always shorten: for ex-
ample, on soft surfaces like gravel or fresh
snow or a slippery surface, the space might
increase.
To better exploit the possibilities of the an-
ti-lock system in the case of need, the ad-
vice given below should be followed.
If the ABS cuts in it means
that the limit of grip is be-
ing reached between the tyre and
the road surface: it is therefore
necessary to slow down to adapt
driving to the grip available.
WARNING
The ABS better exploits the
grip available, but cannot
increase it; caution is therefore nec-
essary on slippery surfaces, with-
out taking unnecessary risks.
WARNING
In the event of a system
failure, with the turning on
of the
>warning light on the
instrument cluster, have the car
checked immediately by Alfa Romeo
Authorised Services driving slow-
ly, to be able to have the system re-
stored to fully efficient conditions.
WARNING