reset Alfa Romeo 147 2005 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2005, Model line: 147, Model: Alfa Romeo 147 2005Pages: 291, PDF Size: 5.52 MB
Page 26 of 291
GETTING TO KNOW YOUR CAR
24
POWER WINDOWS
The power windows are fitted with a safe-
ty system with crush-prevention seals. The
electronic control unit that operates the sys-
tem is capable of detecting the presence of
an obstacle during the window closing mo-
tion through the special seals. Should this
occur, the system stops the movement of
the window and reverses it immediately.
IMPORTANTIf the crush-prevention
function is operated for 3 times in 1 minute,
the system automatically sets to the recov-
ery mode (self-protection). To reset the cor-
rect system operating logic, use the control
button. The window will rise in predefined
steps until closing completely. The logic is
reset and if there are no faults, the window
winder automatically resumes normal op-
eration; if not, contact Alfa Romeo Autho-
rised Services.
IMPORTANTWith the ignition key at
STOPor removed, the power windows re-
main activated for about 3 minutes and are
deactivated immediately the moment a door
is opened.
fig. 33
A0A0043m
fig. 34
A0A0044m
Passenger’s side (fig. 34)
The button (A) controls the passenger’s
side window.
IMPORTANTThe passenger side pow-
er window is provided with an “automatic
continuous operation” device both to low-
er and to raise the window. A brief push on
the upper or lower part of the button is suf-
ficient to start the run which continues au-
tomatically: the window stops at the re-
quired position by pushing once again in-
differently the upper or lower part of the but-
ton. Driver’s side (fig. 33)
The driver’s door panel contains the but-
tons that control the following windows,
with the ignition key at MAR:
A- left front window
B- right front window.
Press the button to lower the window. Pull
to raise it.
IMPORTANTThe driver’s power window
is fitted with the “continuous automatic op-
eration” device for both lowering and raising
the window. A brief press on the upper or
lower part of the button will cause it to move
and continue automatically: the window
stops in the required position by pressing ei-
ther the upper or lower part of the button
again.
Page 28 of 291
GETTING TO KNOW YOUR CAR
26
The rear seat is fitted with inertial seat belts
with three anchor points with reel for the
side seats and for the centre seat (fig. 36).
Through the reel, the belt automatically
adapts to the body of the passenger wear-
ing it, allowing freedom of movement.
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the web-
bing coming out when it is jerked or if the
car brakes sharply, in a collision or when cor-
nering at high speed.To unfasten the seat belts, press button
(C). Guide the seat belt with your hand while
it is rewinding, to prevent it from twisting.
fig. 36
A0A0386m
Never press button (C)
when travelling.
WARNING
fig. 36a
A0A0708m
When the seat back is cou-
pled properly, the “red
band” (B) next to the seat back
levers (A) disappears. The “red
band” actually indicates improper
seat back coupling (fig. 36a). When
resetting it in proper position,
make sure to hear the locking click.
WARNING
After tilting, when reset-
ting the rear seat in
straight position, take care to repo-
sition the seat belt properly to
have it ready for use.
WARNING
Make sure the seat back is
correctly hooked on both
sides (not visible “red bands” (B))
to prevent seat back being thrown
forwards and injuring passengers
should you brake sharply.
WARNING
Page 49 of 291
GETTING TO KNOW YOUR CAR
47
The device is disengaged automatically in
any one of the following cases:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR or VDC, MSR system cuts in.
CONTROLS(fig. 65)
Cruise Control is controlled by the
ON/OFFknurled ring (A), by the +/–
ring (B) and by the RESbutton (C).
Ring (A) has two positions:
–OFFin this position the device is deac-
tivated;
–ONis the normal operating position of
the device. When the knurled ring (A) is
in this position, the warning light
Üon the
instrument cluster turns on.Ring (B) serves for memorising and main-
taining the car speed or for increasing or low-
ering the speed memorised.
Turn the ring (B) to (+) to memorise the
speed reached or increase the speed mem-
orised.
Turn the ring (B) to (–) to lower the speed
memorised.
Each time the ring is actuated (B) the speed
increases or lowers by about 1.5 km/h.
Keeping the ring turned the speed changes
continuously. The new speed reached will
be maintained automatically.
TheRESbutton (C) resets the memorised
speed.
IMPORTANTTurning the ignition key to
STOPor the ring (A) to OFF, the speed
memorised is cleared and the system is
switched off.
CRUISE CONTROL
GENERAL
The speed regulator (CRUISE CON-
TROL), with electronic control, makes it
possible to drive the car at the required
speed without pressing the accelerator ped-
al. This reduces driving fatigue during long
journeys because the speed memorised is
automatically maintained.
IMPORTANTThe device can only be en-
gaged at speeds above 30 km/h.
fig. 65
A0A0077m
Cruise control must be ac-
tivated only when the
route and traffic allow a constant
speed for a sufficiently long dis-
tance completely safely.
WARNING
Page 50 of 291
GETTING TO KNOW YOUR CAR
48
TO MEMORISE THE SPEED
Move the ring (A) to ONand take the car
to the required speed normally. Turn the ring
(B) to (+) for at least three seconds, then
release it. The car speed is memorised and
it is therefore possible to release the accel-
erator pedal.
The car will continue to travel at the mem-
orised constant speed until one of the fol-
lowing conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR or VDC system cuts in.
IMPORTANTIn the case of need (when
overtaking for instance) acceleration is pos-
sible simply pressing the accelerator pedal;
later, releasing the accelerator pedal, the car
will return to the speed memorised previ-
ously.
TO RESET
THE MEMORISED SPEED
If the device has been disengaged for ex-
ample pressing the brake or clutch pedal,
the memorised speed can be reset as fol-
lows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time of
speed memorising (4th, 5th or 6th speed);
– press the RESbutton (C).
TO INCREASE
THE MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then mem-
orising the new speed reached (turning the
ring (B) for more than three seconds);
or
2) momentaneously turning the ring (B) to
(+): each pulse of the ring will correspond to
a slight increase in speed (about 1.5 km/h)
while pressing continuously will correspond
to a continuous speed increase. Releasing the
ring (B) the new speed will be memorised
automatically.
Page 51 of 291
GETTING TO KNOW YOUR CAR
49
The device may only be engaged in 4th,
5th or 6th gear, depending on the speed
of the car. Travelling downhill with the de-
vice engaged the car speed may increase
more than the memorised one, due to the
change in the engine load.
The ring (A) may be left constantly at ON
without damaging the device. You are, how-
ever, advised to switch the device off when
not in use, turning the ring to OFF, to avoid
memorising speeds by accident. It is advisable to engage the cruise control
only when the conditions of the traffic or
road so permit under completely safe con-
ditions, i.e.: straight and dry roads, dual car-
riageways or motorways, flowing traffic and
smooth road surface. Do not engage the de-
vice in town or in heavy traffic conditions.TO REDUCE
THE MEMORISED SPEED
The speed memorised can be reduced in
two ways:
1) disengaging the device (for instance
pressing the brake pedal) and then memo-
rising the new speed (turning the ring (B)
to (+) for at least three seconds);
2) keeping the ring pressed (B) at (–)
until reaching the new speed which will be
memorised automatically.
Cruise Control can only be
engaged at speeds above
30 km/h. The max. speed at which
the Cruise Control can be engaged
is 190 km/h, at speeds higher than
190 km/h it will not be engaged.
WARNING
When travelling with the
cruise control on, do not
move the gearshift lever to neu-
tral.
WARNING
If the device is faulty or
not working, turn the ring
(A) to OFF and contact Alfa Romeo
Authorised Services after checking
that the protection fuse is intact.
WARNING
RESETTING THE MEMORISED
SPEED
The memorised speed is automatically re-
set turning off the engine or moving the ring
(A) to OFF.
Page 52 of 291
GETTING TO KNOW YOUR CAR
50
DASHBOARD
1. Side swivel air vents - 2. Fixed side window air vents - 3. Outer light control lever - 4. Speedometer with mileage recorder and trip recorder
and headlamp aiming display - 5. Fuel level gauge with reserve warning light - 6. Multifunction display - 7. Engine coolant fluid temperature
gauge - 8. Rev counter - 9. Tailgate release button - 10. Card holder - 11. Radio - 12. Centre swivel air vents - 13. Fixed upper vent - 14.
Glass holder - 15. Fog lamp button - 16. Hazard warning light switch - 17. Rear fog guard button - 18. Passenger’s front Air bag - 19. Glove-
box - 20. Door locking button - 21. Controls for heating, ventilation and climate control - 22. Cigar lighter - 23. Ashtray - 24. Temperature
sensor - 25. Windscreen/rearscreen wiper control lever - 26. Ignition key and switch - 27. Horn - 28. Steering wheel locking/release lever -
29. Driver’s front Air bag - 30. Set of controls: trip meter reset, headlamp aiming device, trip computer - 31. Bonnet opening lever. fig. 66
A0A0426m
Page 53 of 291
GETTING TO KNOW YOUR CAR
51
MILEAGE RECORDER
Display with double meter (total and trip)
and headlamp position display.
The display shows:
– the mileage on the first line (6 figures)
– the trip meter on the second line (4 fig-
ures)
– the position relating to the headlamp
aiming device.
To reset the trip meter, keep the button
(A-fig. 68) on the plate at the side of the
steering column pressed for a few seconds.IMPORTANTIf the battery is discon-
nected the trip meter reading is not stored. A. Fuel level gauge with reserve warning
light - B. Engine coolant fluid temperature
gauge with maximum temperature warning
light - C. Speedometer - D. Display (mileage
recorder, trip meter and headlamp position
display) - E. Reconfigurable multifunction
display - F. Rev counter
REV COUNTER
The rev. counter shows engine rpm. The nee-
dle pointed to the danger area (red) indicates
excessive high engine speed. Do not drive for
long periods with the needle in this area.
IMPORTANTThe electronic injection con-
trol system gradually shuts off the flow of fu-
el when the engine is “over-revving” resulting
in a gradual loss of engine power.
When the engine is idling, the rev counter
may indicate a gradual or sudden highering of
the speed, this is normal as it takes place dur-
ing normal operation, for example when en-
gaging the climatecontrol system or the fan.
In particular a slow change in the speed pre-
serves the battery charge.
fig. 67
A0A0427m
INSTRUMENT PANEL
fig. 68
A0A0466m
Page 56 of 291
GETTING TO KNOW YOUR CAR
54
CONTROL BUTTONS (fig. 69-70)
To use the information the reconfigurable multifunction display is able to give (with the ignition key at MAR) you should firstly familiarise
with the control buttons (on the plate at the side of the steering column and on the top of the right lever) using them as described below. Be-
fore doing anything you are also advised to read this chapter in full.
fig. 69
fig. 70
Press for less than 1 second (pulse) indicated withTin the following dia-
grams to move to the next screen
Press for more than 4 seconds indicated with
Uin the following diagrams, to
reset and then start a new journey
To scroll the display and the related options, upwards or to increase the value
displayed depending on the case
To scroll the display and the related options, down wards or decrease the value
displayed according to the case Press for less than 1 second (pulse) indicated with
Qin the following dia-
grams, to confirm the choice required and/or move to the next screen or ac-
cess the Menu
Press for more than 2 seconds indicated with
Rin the following diagrams,
to confirm the choice required and return to the standard screen
A0A0022m
A0A0021m
IMPORTANTButtonsâandãactivate different functions depending on the following
situations:
- When the standard screen is activated, they allow adjustment of the inner lighting
- Within the menu they allow scrolling up or down
- They make it possible to increase or decrease during setting operations.
Page 72 of 291
GETTING TO KNOW YOUR CAR
70
SERVICE
With the SERVICE function it is possible to
receive information connected with correct
vehicle maintenance. To consult this func-
tion, proceed as follows:
Menu screen
Return to menu screen
Return
to standard screen
WARNING
The programmed Mainte-
nance Schedule includes ve-
hicle maintenance every
20,000 km; this is shown
automatically, with the ignition key at MAR, start-
ing from 2,000 km (or miles) from this deadline and
it is shown again every 200 km. This display can on-
ly be reset by Authorised Alfa Romeo Services.
Q
QR
â
ã
â
ã
â
ã
â
ãâ
ãâ
ã
â
ã
â
ã
See INITIAL CHECK and ACCESS
TO THE MENU SCREEN
Page 74 of 291
GETTING TO KNOW YOUR CAR
72
GENERAL TRIP - TRIP B
The TRIP COMPUTER function enables displaying on the re-configurable multifunction display the engine oil temperature and the sizes rele-
vant to the car operating conditions. This function comprises the GENERAL TRIP concerning the complete mission of the car and TRIP B con-
cerning the partial car mission. This function (as shown in the graph below) is contained within the complete mission. Both functions are re-
settable.
The GENERAL TRIP displays the figures relating to
ACTUAL CONSUMPTION,AVERAGE CONSUMPTION,RANGE,AVERAGE VELOCITY,TRAVEL TIME(driving time),
TRAVEL DISTANCE.
TRIP B (with automatic reset each time at least 2 hours have passed since stopping the engine), displays information concerning
AVERAGE CON-
SUMPTION B,AVERAGE VELOCITY B,TRAVEL TIME B(driving time), TRAVEL DISTANCE B.
Start of journey procedure (reset)
To start a new journey monitored by the GENERAL TRIP, with the ignition key at MAR, press the button with
U(see “Control buttons”).
The reset operation (pressing the
Ubutton) in the presence of the screens concerning the GENERAL TRIP also makes it possible to reset
TRIP B. The reset operation (pressing the
Ubutton) in the presence of only the screens concerning TRIP B makes it possible to reset only the
information associated with this function.
IMPORTANTThe
RANGEandACTUAL CONSUMPTIONinformation cannot be reset.
End of partial mission
Start of new partial mission
Reset TRIP B
˙Reset TRIP B
End of partial mission
Start of new partial mission˙
˙Reset TRIP B
˙˙
˙
TRIP B
TRIP B
TRIP B
End of partial mission
Start of new partial missionEnd of partial mission
Start of new partial mission
Reset TRIP B
GENERAL TRIP
End of complete mission
Start of new mission
Reset GENERAL TRIP
˙
End of complete mission
Start of new mission
Reset GENERAL TRIP
˙