seats Alfa Romeo 147 2005 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2005, Model line: 147, Model: Alfa Romeo 147 2005Pages: 291, PDF Size: 5.52 MB
Page 18 of 291
FRONT SEATSCENTRAL LOCKING
This allows central locking of the door
locks.
To engage central locking, the doors must
be perfectly shut, otherwise, locking is de-
nied.
IMPORTANTWith central locking en-
gaged, pulling the inside lever for opening
one of the doors causes the unlocking also
of the other door.
In the event of a power cut off (blown
fuse, battery disconnected, etc.) it is still pos-
sible to work the lock by hand.
fig. 11
A0A0019m
GETTING TO KNOW YOUR CAR
16
OPENING/CLOSING
FROM INSIDE
To open the door, pull the handle
(A-fig. 10).
To close the door, pull it; then to prevent
opening from outside, press the button (A-
fig. 11) on the dashboard, the deterrent
led (B) on the actual button lights up with
a yellow light to confirm that locking has
taken place.
fig. 12
A0A0409m
Any adjustments are to be
carried out only with the
vehicle stationary.
WARNING
fig. 10
A0A0018m
Page 19 of 291
GETTING TO KNOW YOUR CAR
17
LENGTHWISE ADJUSTMENT
(fig. 12)
Raise the lever (A) and push the seat
backwards or forwards; in the driving posi-
tion the arms should be slightly flexed and
the hands should rest on the rim of the steer-
ing wheel.
DRIVER’S SEAT HEIGHT
ADJUSTMENT
(fig. 12)
To raise the seat, pull the lever (B) up-
wards, then work the lever (up and down)
until reaching the required height, then re-
lease it. To lower the seat, push the lever
(B) downwards then work the lever (up and
down) until reaching the required height.
IMPORTANTAdjustment must be car-
ried out only seated in the driver’s seat.
BACK REST ANGLE
ADJUSTMENT
(fig. 12)
Turn the knob (C) until reaching the posi-
tion required.
TILTING THE BACK REST
(fig. 12)
To gain access to the rear seats, pull the
handle (E), the back rest folds and the seat
is free to run forwards.
A recovery mechanism with memory
makes it possible to take the seat back to
its previous position.
Once the seat back has been returned to
the travelling condition, make sure that it
is correctly clamped, checking that the “red
band” on the upper part of the handle (E)
is concealed. In fact, this “red band” indi-
cates that the seat back is not camped.
Also check that the seat is firmly locked on
the runners, trying to move it to and from.
DRIVER’S SEAT LUMBAR
ADJUSTMENT
(fig. 12)
Turn the knob (D) until obtaining the most
comfortable position.
After releasing the adjust-
ment lever, always check
that the seat is locked on the run-
ners, trying to move it to and from.
The lack of this clamping action
could cause the seat to move un-
expectedly and cause loss of ve-
hicle control.
WARNING
Page 20 of 291
GETTING TO KNOW YOUR CAR
18
CENTRAL ARMREST (fig. 13)
The armrest is adjustable and can be raised
or lowered to the required position.
To adjust, slightly raise the armrest, then
press the release device (A).
Inside the armrest there is an oddments
compartment, to use it, raise the cover,
pressing the device (B).SEAT WARMING (fig. 14)
(optional for versions/markets
where applicable)
The seat warming pad can be switched on
and off using switch (A) on the outer side
of the seat.
Switching on is shown by the lighting up
of the led (B) on the switch itself.REAR POCKETS (fig. 15)
(for versions/markets
where applicable)
The front seats are fitted with a pocket in
the rear of the back rest.
fig. 14
A0A0485m
fig. 15
A0A0413m
fig. 13
A0A0412m
Page 21 of 291
GETTING TO KNOW YOUR CAR
19
REAR SEATS
EXTENDING THE
LUGGAGE COMPARTMENT
The split rear seat makes it possible to ex-
tend the luggage compartment totally or par-
tially, acting separately on one of the two
parts, thereby offering different possibilities
of load depending on the number of rear
passengers.Removing the rear parcel shelf
Proceed as follows:
– free the ends of the two rods (A-fig.
16) supporting the parcel shelf (B) pulling
the eyelets (C) off the pins (D);
– release the pins (A-fig. 17) at the out-
side of the shelf from their housings (B) ob-
tained in the side supports, then remove the
shelf pulling it outwards.
After removal the shelf can be placed in
two ways:
– crossways in the luggage compartment
as shown in fig. 18;
– crossways between the front seat back
reats and the tilted cushions of the rear seats
if the boot is extended totally (see fig. 22).Total extension
Proceed as follows:
– position the seat belt buckles (A-fig.
19) in their housings in the cushion;
– pull the handles in the centre of the cush-
ions, then tilt them forwards;
fig. 16
A0A0414m
fig. 17
A0A0028m
fig. 19
A0A0416mfig. 18
A0A0415m
If a particularly heavy load
is placed in the boot, when
travelling at night, it is wise to
check the height of the high beams
(see “Headlamps” paragraph).
WARNING
Page 23 of 291
GETTING TO KNOW YOUR CAR
21
HEADREST ADJUSTMENT
(fig. 23)
The car may be fitted with two headrests
for the side seats and, depending on the trim
level, it may also have a third headrest in
the centre.
The headrests have 2 positions
(up/down) depending on the height of the
passenger.
In the case of need, it is possible to remove
the headrests as described previously (see
“Luggage compartment extension”).
CENTRAL ARMREST (fig. 24)
To use the armrest (A), lower it as illus-
trated.
LUGGAGE
RETAINER NET
Present only on certain versions, the inte-
rior fittings are completed by the luggage re-
tainer net, which is helpful in correctly ar-
ranging the load and/or suitable for trans-
porting light materials.
Fig. 25, 26, 27below show the various
clamping solutions for the net in the boot.
fig. 23
A0A0417m
fig. 24
A0A0418mfig. 25
A0A0326m
Remember that headrests
should be adjusted so that
the nape, and not the neck, rests
on them. Only in this position do
they exert their protective action
in the event of a crash from behind.
WARNING
fig. 26
A0A0327m
Page 28 of 291
GETTING TO KNOW YOUR CAR
26
The rear seat is fitted with inertial seat belts
with three anchor points with reel for the
side seats and for the centre seat (fig. 36).
Through the reel, the belt automatically
adapts to the body of the passenger wear-
ing it, allowing freedom of movement.
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the web-
bing coming out when it is jerked or if the
car brakes sharply, in a collision or when cor-
nering at high speed.To unfasten the seat belts, press button
(C). Guide the seat belt with your hand while
it is rewinding, to prevent it from twisting.
fig. 36
A0A0386m
Never press button (C)
when travelling.
WARNING
fig. 36a
A0A0708m
When the seat back is cou-
pled properly, the “red
band” (B) next to the seat back
levers (A) disappears. The “red
band” actually indicates improper
seat back coupling (fig. 36a). When
resetting it in proper position,
make sure to hear the locking click.
WARNING
After tilting, when reset-
ting the rear seat in
straight position, take care to repo-
sition the seat belt properly to
have it ready for use.
WARNING
Make sure the seat back is
correctly hooked on both
sides (not visible “red bands” (B))
to prevent seat back being thrown
forwards and injuring passengers
should you brake sharply.
WARNING
Page 29 of 291
GETTING TO KNOW YOUR CAR
27
FRONT SEAT BELT HEIGHT
ADJUSTMENT
The front seat belt ring can take different
positions which make it possible to adjust
the height of the belts.
Always adjust the height of the belts adapt-
ing it to the person who is wearing it. This
precaution improves their effectiveness. sub-
stantially reducing the risk of injury in the
event of a crash.
Correct adjustment is obtained when the
belt passes half way between the end of the
shoulder and the neck.
To adjust, lower or raise the grip (A-
fig. 38) of the locking device, at the same
time moving the ring (B) to the most ap-
propriate of the allowed positions.
LOAD LIMITERS
To increase passive safety, the front seat
belt reels contain a load limiter which allows
controlled sag in such a way as to dose the
force acting on the shoulders during the belt
restraining action.
fig. 47
A0A0419m
When the rear seats are not occupied, use
the spaces provided in the cushion to stow
the belt buckles.
fig. 37
A0A0387m
To offer the highest level of
protection, the rear seat
belts should be fastened as shown
in fig. 36.
WARNING
Remember that, in the
event of an accident, any
passengers occupying the rear
seats who are not wearing a seat
belt not only subject themselves to
great personal risk but constitute
a danger to the occupants of the
front seats.
WARNING
After adjustment, always
check that the slider (B-
fig. 38) is anchored in one of the
positions provided. To do this, with
the button (A-fig. 38) released, ex-
ert a further pressure to allow the
anchor device to catch if release did
not take place at one of the pre-
set positions.
WARNING
Make the height adjust-
ment when the car is sta-
tionary.
WARNING
Page 33 of 291
GETTING TO KNOW YOUR CAR
31
CARRYING CHILDREN SAFELYFor the best level of protection in the event
of a crash, all occupants must travel seated
and secured by suitable restraint systems.
This is even more important for children.
According to 2003/20/EC Directive, this
prescription is compulsory for all European
Community countries.
Compared with adults, a child’s head is pro-
portionately larger and heavier than the rest
of the body, while muscles and bone struc-
ture are not completely developed. There-
fore, in order to restraint them correctly in
the event of a crash, different systems are
needed then adult seat belts.
fig. 42
A0A0388m
SERIOUS DANGER! Never place cradle child’s seats on the
front passenger seats of cars equipped with passenger air
bag since the air bag activation could cause serious injuries, even mortal.
You are advised to carry children always on the rear seat, as this is the
most protected position in the case of a crash. In any case, child’s seats
must absolutely not be positioned on the front seat of car’s with passen-
ger’s air bag, which during inflation could cause serious injury, even mor-
tal, regardless of the seriousness of the crash that triggered it. Children
may placed on the front seat of cars fitted with passenger’s air bag deac-
tivation. In this case, it is absolutely necessary to check the warning light
Fon dial to make sure that deactivation has actually took place (see para-
graph “Front and side air bags“ at item “Front passenger air bag“). The
front passenger seat shall be adjusted in the most backward position to
prevent any contact between the child’s seat and the dashboard.
WARNING
Page 34 of 291
GETTING TO KNOW YOUR CAR
32
GROUP 1
Starting from 9 kg to 18 kg in weight, chil-
dren may be carried facing forwards with
seats fitted with front cushion (fig. 44),
through which the car seat belt restrains both
child and seat. The results of research on the best pro-
tection for a child are summarised in Euro-
pean Standard ECE-R44, which in addition
to making them compulsory, subdivides re-
straint systems into five groups:
Group 0 until 10 kg in weight
Group 0+ until 13 kg in weight
Group 1 9-18 kg in weight
Group 2 15-25 kg in weight
Group 3 22-36 kg in weight
As it may be noted, the groups partially
overlap and in fact, in commerce it is pos-
sible to find devices that cover more than
one weight group (fig. 42).
All the restraint devices must bear the ho-
mologation data, together with the control
brand, on a solidly fixed label which must
absolutely not be removed.
Over 1.50 m in height, from the point of
view of restraint systems, children are con-
sidered as adults and wear belts normally.
The Lineaccessori Alfa Romeo includes
seats for each weight group, which are the
recommended choice because they have
been designed and specifically experiment-
ed for Alfa Romeo cars.
GROUP 0 and 0+
Babies up to 13 kg must be carried fac-
ing behind (fig. 43) on a cradle seat,
which, supporting the head, does not induce
strain on the neck in the event of sharp de-
celeration.
The cradle is restrained by the car safety
belts, as illustrated, and it should in turn
restrain the child with the belts incorporat-
ed on it.
fig. 43
A0A0389m
fig. 44
A0A0390m
The illustration is indica-
tive only for assembly. As-
semble the seat according to the
compulsory instructions provided
with it.
WARNING
The illustration is indica-
tive only for assembly. As-
semble the seat according to the
compulsory instructions provided
with it.
WARNING
Page 35 of 291
GETTING TO KNOW YOUR CAR
33
GROUP 2
Starting from 15 to 25 kg in weight, chil-
dren may be restrained directly by the car
seat belts. Child seats only have the func-
tion of positioning the child correctly in re-
lation to the belts, so that the diagonal part
adheres to the chest and never to the neck
and that the horizontal part adheres to the
child’s pelvis and not to the abdomen (fig.
45).
GROUP 3
For children from 22 kg up to 36 kg the
child’s chest is thick enough not to need the
spacer back rest any more.
fig. 46shows proper child seat posi-
tioning on the rear seat.
Over 1.50 m in height, children may wear
seat belts like adults.
fig. 45
A0A0391m
fig. 46
A0A0392m
The illustration is indica-
tive only for assembly. As-
semble the seat according to the
compulsory instructions provided
with it.
WARNING
The illustration is indica-
tive only for assembly. As-
semble the seat according to the
compulsory instructions provided
with it.
WARNING
Seats exist which are suit-
able for covering weight
groups 0 and 1 with a rear connec-
tion to the car belts and its own
belts to restrain the child. Because
of their mass, they can be danger-
ous if installed incorrectly fastened
to the car belts with a cushion.
Strictly adhere to the assembly in-
structions provided.
WARNING