remote control Alfa Romeo 156 2005 Owner handbook (in English)

GETTING TO KNOW YOUR CAR6
ALFA ROMEO
CODE SYSTEMTo increase protection against attempted
theft, the car is fitted with an electronic en-
gine lock system (Alfa Romeo CODE) which
is activated automatically when the ignition
key is removed. In fact the grip of each key
contains an electronic device which modu-
lates the radio frequency signal transmit-
ted when the engine is started by a special
aerial incorporated in the ignition switch. This
modulated signal is the “password” by
which the control unit recognises the key
and only in this condition can the engine
be started.
THE KEYSThe car is delivered with two keys, key
(A-fig.1) with metal insert and remote
control function and another key with metal
insert only, without remote control.
The key remote control operates:
– door centralised opening/locking
– opening luggage compartment boot/
tailgate
– activation/deactivation of electronic
alarm (if existing)
G G
E E
T T
T T
I I
N N
G G

T T
O O

K K
N N
O O
W W

Y Y
O O
U U
R R

C C
A A
R R
SYMBOLSSpecial coloured labels have been attached
near to or actually on some of the compo-
nents making up your Alfa 156.
These labels bear symbols that remind you
of the precautions to be taken as regards
that particular component.
fig. 1
A0B0016m

GETTING TO KNOW YOUR CAR7
Key metal insert operates:
– the ignition switch
– the driver's door lock and, optional for
versions/markets where applicable, the pas-
senger's door lock
– passenger’s side Air bag deactivation.
WARNINGIn order to ensure perfect ef-
ficiency of the electronic devices contained
inside the keys, they should never be directly
exposed to the rays of the sun.
If the car changes owner,
the new owner must be
given all the keys and the
CODE card.
fig. 2
A0B0010m
The CODE card (fig. 2) is also supplied
with the key and it contains the codes of the
keys (both the mechanical one and the elec-
tronic one for emergency starting).
The code numbers on the CODE card must
be kept in a safe place, not in the car.
The driver should always keep the elec-
tronic code given on the CODE card with him
in the event of having to carry out emer-
gency starting.
KEY WITH REMOTE CONTROLThe key with remote control (fig. 3) is
fitted with:
– a metal insert (A) that can be enclosed
in the key grip
– button (B) for remote opening/clos-
ing of the doors and turning the electronic
alarm on/off (where fitted)
– a button (C) for remote boot unlock-
ing
– removable hook ring (D)
– a button (E) for power-assisted opening
of the metal insert.fig. 3
A0B9000m

GETTING TO KNOW YOUR CAR8
To insert the metallic insert in the key grip,
press the button (E-fig. 3) to release the
insert and turn it in the direction of the ar-
row until it clicks.
To open/close the doors by remote con-
trol, press button (B). On cars fitted with
electronic alarm system, pressing button (B)
also turns the electronic alarm.
WARNINGCertain radio devices outside
the car (e.g. mobile phones, HAM radio sys-
tems) could disturb the remote control fre-
quency. In this case the remote control could
malfunction.
OPENING THE BOOTThe boot can be opened by remote control
from outside pressing button (C-fig. 3),
also when the electronic alarm (where fit-
ted) is on.
In this case the alarm system switches off
the boot volumetric protection and control
sensor, the system gives two “beeps” (with
the exceptions of versions for certain mar-
kets) and the direction indicators light up for
about three seconds.
Closing the boot again, the control func-
tions are restored, the system gives two
“beeps” (with the exceptions of versions for
certain markets) and the direction indicators
light up for about three seconds. The metallic insert (A) of the key oper-
ates:
– the ignition switch
– the driver's door lock and, optional for
versions/markets where applicable, the pas-
senger's door lock
– passenger’s Air bag deactivation.
To move the metallic insert out of the key
grip, press button (E).
When button (E) is
pressed, take the utmost
care to prevent the metal insert
from causing injury or damage
when it comes out. Button (E) must
only be pressed when the key is
away from the body, in particular
the eyes, and from objects that
could be spoilt (e.g. clothes). Never
leave the key unattended to pre-
vent anyone, especially children,
from holding it and pressing button
(E) inadvertently.
WARNING

GETTING TO KNOW YOUR CAR10
2)If the warning lamp flashes it means
that the car is not protected by the immo-
biliser. Contact your Alfa Romeo Authorized
Service immediately and get them to store
the codes of all the keys in the memory.
CHANGING THE BATTERY
OF THE KEY WITH REMOTE
CONTROLIf when pressing button (Bor C-fig. 5)
the control is rejected or is not performed,
the battery should be replaced by a new one
of the same type to be found c/o normal
retailers. On versions fitted with electronic
alarm, the need to replace the remote con-
trol battery is indicated by the coming on,
with fixed light, of the deterrent led set on
the dashboard near the central air vent. If after 2 seconds with
the key in the MAR posi-
tion, the warning light turn
on again flashing, this means that
the code of the keys has not been
memorised, thus the car is not pro-
tected by the Alfa Romeo CODE
system against attempted theft. In
this case, contact an Alfa Romeo
Authorized Service to have the key
codes memorised.
Dead batteries are harm-
ful for the environment.
They must be disposed of
in special containers as specified by
current regulations. Avoid expo-
sure to naked flames and high tem-
peratures. Keep out of reach of
children.
fig. 5
A0B9000m
WARNINGThe system is protected by
a 10 A fuse housed in the fuse-holder set
under the dashboard (see paragraph “If a
fuse or relay blows” in the chapter “In an
emergency”).

GETTING TO KNOW YOUR CAR11
To change the battery (fig. 7):
– move the metal insert (A) to the un-
locking position;
– turn the pin (B), taking the reference
mark (dot) of the cut to the UNLOCKpo-
sition (2);
– working on the notch (C) remove the
battery holder (D);
– change the battery (E) putting it in the
position shown on the holder;
– insert the holder back in the key and
lock it, turning the reference mark of the pin
(B) to the LOCKposition (1).
ELECTRONIC ALARM(optional for versions/markets
where applicable)DESCRIPTIONThe system comprises: transmitter, re-
ceiver, control unit with siren and volumet-
ric sensors and anti-lift sensor. The electronic
alarm is controlled by a receiver inside the
car and it is turned on and off through the
remote control incorporated in the key which
sends the crypted and variable code. The
electronic alarm monitors: unlawful opening
of the doors, bonnet and boot (perimetral
protection), operation of the ignition key,
battery and emergency key cable cutting,
the presence of moving bodies (volumetric
protection), any abnormal raising/sloping
of the car (for versions/markets where ap-
plicable) and operates the central door lock-
ing system. It also makes it possible to cut
off the volumetric protection.
WARNINGThe engine inhibitor function
is guaranteed by the Alfa Romeo CODE sys-
tem which is activated automatically when
the ignition key is removed.
fig. 7
A0B0047m
REMOTE CONTROL
(fig. 8)
The remote control is built into the key and
it is fitted with a button for activating the
alarm (B-fig.8)
fig. 8
A0B9000m

GETTING TO KNOW YOUR CAR12
REQUEST FOR ADDITIONAL
KEYS WITH REMOTE CONTROLThe receiver can recognise up to 5 keys
with remote control. If during the life of the
car a new key with remote control is needed
for any reason whatsoever, contact Alfa
Romeo Authorized Services directly, taking
with you the CODE card, a personal iden-
tity document and the car’s possession doc-
uments.
ACTIVATING THE ALARMWhen the doors and boot/bonnet lids are
closed and the ignition key is in the STOP
or PARKposition (key removed), point the
remote control towards the car and then
press and release the button (B-fig. 8).
With the exception of some markets the
system sounds a beep and the door lock is
engaged.
Engagement of the alarm is preceded by
a self-diagnosis phase characterised by a
change in the frequency at which the de-
terrent led (A-fig. 9) on the dashboard
flashes. If an anomaly is detected the sys-
tem gives off a further beep.fig. 9
A0B0563m
Surveillance
When the system has been turned on, the
led (A-fig. 9) on the dashboard will flash
to indicate that the system is in the surveil-
lance mode. The led will flash continuously
while the system is under surveillance.
WARNINGOperation of the electronic
alarm is adapted at the origin to the regu-
lations of the different countries.

GETTING TO KNOW YOUR CAR13
Self-diagnosis and monitoring
of doors and bonnet/boot
If, after the alarm has been activated, a
second acoustic signal is heard, check that
all the doors and bonnet/boot are closed
properly and engage the system once again.
On the other if a door or bonnet/boot lid
is not correctly closed it will not be controlled
by the system.
If the control signal is repeated when the
doors and bonnet/boot are closed properly
this means that the self-diagnosis function
has detected a system operating fault, in
which case it is necessary to contact Alfa
Romeo Authorized Services.
DEACTIVATING THE ALARMTo deactivate the alarm, press the button
on the key with remote control. The system
performs the following (with the exception
of some markets):
– the direction indicators turn on twice
briefly
– two beeps are sounded briefly by the
siren
– the doors are released.
WARNINGIf the led (A-fig. 9) in the
car stays on when the system has been de-
activated, (maximum of 2 minutes or until
the ignition key is moved to MAR) the fol-
lowing should be borne in mind:
– if the led stays on permanently, it means
that the remote control batteries are flat and
need replacing;– if the led continues to flash, but at dif-
ferent intervals than normal, it means that
attempts to steal the car have been made,
counting the number of flashes it is also pos-
sible to identify the type of attempt:
1 flash: right front door
2 flashes: left front door
3 flashes: right rear door
4 flashes: left rear door
5 flashes: volumetric sensors
6 flashes: bonnet
7 flashes: boot
8 flashes: tampering with car starting
cables
9 flashes: tampering with battery or
cutting emergency key ca-
bles
10 flashes: at least three causes of
alarm.

GETTING TO KNOW YOUR CAR14
AUTOMATIC ENGAGEMENT
OF THE ALARM (optional for versions/markets
where applicable)
If the alarm has not been engaged with
the remote control it will come on auto-
matically after an established time of 30
seconds from the moment that the ignition
key has been turned to the STOPor
PARKpositions and a door or the boot has
been opened and then closed again. This
condition is shown by the intermittent illu-
mination of the led in the car and by the sig-
nalling described previously.
To deactivate the alarm press the button
on the remote control.
The alarm is also automatically engaged
when the doors are closed using the key.
When the alarm is engaged automatically
the doors are not locked.
WHEN THE ALARM
IS TRIGGEREDWhen the alarm is engaged it will sound
when:
– one of the doors, the bonnet or the tail-
gate is opened;
– the battery is disconnected or the elec-
tric cables are cut, or the emergency key ca-
bles are cut;
– intrusion into the passenger compart-
ment, e.g. window being broken (volumetric
protection);
– attempt to start the engine (key at
MAR);
– abnormal car raising/sloping (for ver-
sions/markets where applicable).
Depending on the markets, the triggering
of the alarm will activate the siren and the
hazard warning lights (for about 26 sec-
onds). The methods of operation and the
number of cycles may vary depending on
the versions/markets.
However a maximum number of cycles is
foreseen.
Once the alarm cycle has come to an end,
the system will return to its normal moni-
toring state.
INTERRUPTING THE ALARMTo interrupt the alarm press the button on
the remote control or, if the remote control
battery is down, get into the car, insert the
key into the ignition switch and turn the key
to MAR.
WARNINGIf it is necessary for the ve-
hicle to lie inactive for long periods (over 3
weeks), close the vehicle using the key to
deactivate the alarm.

GETTING TO KNOW YOUR CAR15
VOLUMETRIC PROTECTIONTo guarantee correct operation all the win-
dows and the sunroof, if any, should be
closed.
This function can be excluded (for exam-
ple when leaving animals on-board the car)
by performing the following operations in
quick succession: when the key is at MAR,
move the key to the STOPposition and
then return the key to MARand then once
again to the STOPposition. Remove the
ignition key.
The led in the car will come on for about
2 seconds to confirm that the function has
been excluded.To restore volumetric protection move the
ignition key to the MARposition and hold
it in this position for more than 30 seconds.
If requiring to activate an electric control
operated by the ignition key at MAR(e.g.
electric windows) with the volumetric pro-
tection deactivated, turn the ignition key
to MAR, operate the control and return the
key to STOPwithin a maximum time of
30 seconds. This way volumetric protection
is not restored.
CUTTING OUT OPERATION
OF THE SIREN (for versions/markets where
applicable)
When requiring to dispense with the siren
acoustic signalling in the alarm condition,
simply keep the remote control button (B-
fig. 10) pressed for 4 seconds when en-
gaging the system.
This condition is shown by a series of 5
beeps in quick succession after the normal
acoustic/visual signals when the system is
operated.
The next time the system is activated, nor-
mal operation of the siren is restored auto-
matically.fig. 10
A0B9000m

GETTING TO KNOW YOUR CAR16
MINISTERIAL HOMOLOGATIONIn keeping with the laws in force in each
country on the subject of radio frequency,
we point out that:
– the separate homologation numbers for
each market are given on the last pages of
this handbook before the alphabetical index
(for some countries also homologation doc-
ument);
– for markets in which the transmitter
needs to be marked with the homologation
number, this has been stated on the com-
ponent.
(Depending on the versions/markets, the
code may also be marked on the transmit-
ter and/or on the receiver).
REMOTE CONTROL
DOOR LOCKING SYSTEMThe system comprises a receiver inside the
car and a transmitter (remote control) in-
corporated in the key (E-fig. 11).
To lock/unlock the locks, point the trans-
mitter towards the car, press and release the
button (B-fig. 11).WARNINGShould it be necessary to
programme additional remote controls, con-
tact Alfa Romeo Authorized Services.fig. 10
A0B9000m