light Alfa Romeo 166 2008 Owner handbook (in English)

3 VERY IMPORTANT!
FUEL CAPACITY
Petrol engines:only use unleaded petrol with no less than 95 R.O.N.
Diesel engines:only refuel with diesel fuel conforming to the European specification EN590. The use of other products
or mixtures may irreparably damage the engine with invalidation of the warranty due to the damage caused.
K
STARTING THE ENGINE
Petrol engines:engage the handbrake; set the gearshift lever to neutral; fully depress the clutch without pressing the accel-
erator, then turn the ignition key to AV Vand release it as soon as the engine has started.
JTD engines:engage the handbrake; set the gearshift lever to neutral; fully depress the clutch without pressing the ac-
celerator; turn the ignition key to MARand wait for the
mwarning light to go off, then turn the ignition key to AV V
and release it as soon as the engine has started.
PARKING ON FLAMMABLE MATERIAL
While working, the catalyst develops a very high temperature. Do not park the car over grass, dry leaves, pine needles or
any other inflammable materials: risk of fire.


11
Sit comfortably in your vehicle and carefully read through the fol-
lowing pages.
You will immediately recognize the parts described and rapidly get
to know the controls and devices fitted to your vehicle.STR (SPORT THROTTLE RESPONSE) SYSTEM.................................................63
CONSTANT SPEED REGULATOR (CRUISE CONTROL)
...................................64
PARKING SENSORS
...............................................................................................67
INSTRUMENT PANEL
.............................................................................................68
CLIMATE CONTROL
................................................................................................80
CLIMATE CONTROL UNIT
.....................................................................................83
ADDITIONAL HEATER
............................................................................................91
CONTROLS
................................................................................................................93
INTERNAL FITTINGS
..............................................................................................96
SUNROOF
.................................................................................................................103
LUGGAGE COMPARTMENT
..................................................................................105
BONNET
....................................................................................................................109
HEADLIGHTS
............................................................................................................110
EOBD SYSTEM
........................................................................................................113
ABS
.............................................................................................................................114
VDC AND ASR SYSTEMS
.......................................................................................117
SOUND SYSTEM
......................................................................................................122
REFUELLING
............................................................................................................124
FUEL CUT-OFF SWITCH
........................................................................................127
ENVIRONMENTAL PROTECTION
.........................................................................129 DASHBOARD
................................................................................................page 12
ALFA ROMEO I.C.S. SYSTEM: CONTROLS ON STEERING WHEEL
. ..........14
THE ALFA ROMEO CODE SYSTEM
......................................................................16
ELECTRONIC ALARM
..............................................................................................22
REMOTE CONTROL DOOR LOCKING SYSTEM
................................................26
IGNITION DEVICE
...................................................................................................26
DOORS
.......................................................................................................................28
SEATS
.........................................................................................................................31
STEERING WHEEL ADJUSTMENT
.......................................................................36
ADJUSTING THE REAR-VIEW MIRRORS
..........................................................36
POWER WINDOWS
................................................................................................38
SEAT BELTS
...............................................................................................................40
CARRYING CHILDREN SAFELY
............................................................................45
FRONT AND SIDE AIR BAGS
...............................................................................50
LIGHT SWITCHES & STEERING WHEEL LEVERS
............................................57
GETTING TO KNOW YOUR CAR

13
1Air ducts for side window outlets.
2Side air vents.
3Light switch lever (high beam, flash-
ing, direction indicators and controls
for Cruise Control (automatically
keeping a set speed) (if present).
4Instrument cluster.
5Outlets for windscreen.
6Upper outlet.
7Oddments compartment.
8Centre air vents.
9Passenger’s air bag.
10Manual passenger’s side Air bag
deactivation switch.
11Glove box.
12Boot opening button (in glove box).
13Button for rearscreen defrosting,
door mirrors and resistances at base
of windscreen (if present).
14Button for windscreen/front side
windows and door mirrors
defrosting, rearscreen heating,
resistances at base of windscreen (if
present).15Cigar lighter.
16Alfa Romeo I.C.S. (INTEGRATED
CONTROL SYSTEM): RDS radio,
computer on board (TRIP), climate
control, clock and outside/inside
temperature, GSM phone and
navigation system (if present).
17Buttons for central locking, fuel flap
opening, switching off the ASR
function of the VDC system switching
on the STR system (if present).
18Rear fog guard switch.
19Front fog light switch.
20Hazard warning light switch.
21Inside temperature sensor.
22Windscreen wiper/washer control
lever and rain sensor (if present).
23Ignition switch (ignition device).
24Driver’s air bag and horn.
25Lever for releasing/locking adjustable
steering wheel.
26Instrument lighting adjustment.
27Headlamp aiming device control
(except versions with gas discharge
headlights).28Outside lights switch.
29Bonnet opening lever.
30Front floor air outlets.

16
1035PGSm
fig. 5
THE ALFA ROMEO
CODE SYSTEM
To increase protection against attempted
theft, the car is fitted with an electronic
engine lock system (Alfa Romeo CODE)
certified in accordance with EC Directive
95/56 which is activated automatically
when the key is removed from the igni-
tion.
In fact the grip of each key contains an
electronic device which modulates the ra-
dio frequency signal transmitted when the
engine is started by a special aerial incor-
porated in the ignition switch.
This modulated signal is the “password”
by which the control unit recognises the
key and only in this condition can the en-
gine be started.
THE KEYS
The car is provided with the key (A-
fig. 4) with metal insert with power-as-
sisted opening, remote control for opening
the boot and remote control for unlock-
ing/locking the doors and electronic alarm
(where applicable). The key operates:
– the ignition
– door locks
– boot lock
– glovebox lock
– remote door locking/unlocking sys-
tem
– alarm system (optional for versions/
markets where applicable)
– deactivation of the passenger’s Air
bag.
IMPORTANT In order to ensure the
perfect efficiency of the electronic devices
contained inside the key, avoid exposing
it to direct sunlight.
A0D0143m
fig. 4

18
To insert the metallic insert in the key
grip, keep button (B-fig. 6) pressed
and turn the insert on the direction of the
arrow until it clicks into place, then re-
lease the button (B).
To open/close the doors by remote con-
trol, press button (C). On cars fitted with
electronic alarm system, pressing button
(C) also turns the electronic alarm on/off
and the led (D) (where required) flashes
while the transmitter sends the code to
the receiver. This rolling code changes at
each transmission.
IMPORTANTIf led (D) (where re-
quired) flashes only once briefly when
button (C) is pressed, the battery need
changing as described below.Opening the boot
The boot can be opened by remote
control from outside pressing button (E-
fig. 6), also when the electronic alarm
(where fitted) is on.
In this case the alarm disengages the
boot control sensor, the system (with the
exception of versions for certain markets)
sounds two beeps and the direction indi-
cators light up for about three seconds.
When the boot is closed again the con-
trol function is restored, the system (with
the exception of versions for certain mar-
kets) sounds two beeps and the direction
indicators light up for about three sec-
onds.
When button (B) is pres-
sed, take the utmost care
to prevent the metal insert from
causing injury or damage when it
comes out. Button (B) must only be
pressed when the key is away
from the body, in particular the
eyes, and from objects that could
be spoilt (e.g. clothes).
Never leave the key unattended to
prevent anyone, especially chil-
dren, from holding it and pressing
button (B) inadvertently.
WARNING

20
This condition is indicated by a brief
flash of the warning light (A-fig.
10) on the check panel.
If the code has not been recognised cor-
rectly, the Alfa Romeo CODE system
warning light (A-fig. 10) stays on
together with the EOBD/fuel supply-igni-
tion system failure warning light (B-fig.
10) .
In this case, you are recommended to re-
turn the key to the STOPposition and
than back to MAR; if the inhibition per-
sists, try again possibly with the other key
provided with the car. If it is still impossible
to start the car, carry out the emergency
starting procedure described herein and
turn to an Alfa Romeo Authorized Service.
U
¢
¢IMPORTANTEvery electronic key has
its own code, which must be memorised
by the system control unit. To memorise
new keys, up to a maximum of seven,
apply solely to Alfa Romeo Authorized
Services taking with you all the keys in
your possession, the CODE card, a person-
al identity document and the car’s posses-
sion documents.
The codes of the keys
not provided during the
new memorising proce-
dure are erased from the memo-
ry. This is to ensure that any lost
or stolen keys can no longer be
used to start the car.
IMPORTANTThe Alfa Romeo CODE
warning light comes on when travelling
with the ignition key on MAR:
1) If the warning lamp lights up while
the car is moving, it means that the sys-
tem is running a self-diagnosis (e.g. due to
a voltage drop). The first time you stop y-
ou can test the system as follows: switch
the engine off by turning the ignition keytoSTOP; then turn the key back to
MAR: the warning lamp will light up and
should go out in the space of about one
second. If the warning lamp fails to go
out, leave the key at STOPfor more than
30 seconds and repeat the procedure de-
scribed previously. If the problem persists,
contact your Authorised Alfa Romeo Dealer.
2) If the warning lamp flashes it means
that the car is not protected by the immo-
biliser. Contact your Authorized Alfa
Romeo Code Dealer immediately and get
them to store the codes of all the keys in
the memory.
If after about 2 seconds
with the key in the
MAR position, the Alfa
Romeo CODE warning light turns
on again flashing at appr. half
second intervals, this means that
the code of the keys has not
been memorised, thus the car is
not protected by the Alfa Romeo
CODE system against attempted
theft. In this case, contact an Au-
thorized Alfa Romeo Service to
have the key codes memorised.
fig. 10
A0D0091m

21
IMPORTANTIn the case of fast start-
ing, turning the key directly from STOP
toAV V, the recognition code might not
be transmitted completely, preventing the
engine from starting: try again more
slowly.
IMPORTANTThe system is protected
by two fuses housed in the main fusebox
(see “If a fuse or relay blows” in the
chapter “In an emergency”).
EMERGENCY STARTING
If it is not possible to deactivate the en-
gine inhibitor with the ignition key, Alfa
Romeo Authorized Services can carry out
the emergency procedures using the code
of the CODE card, or, you may do this
yourself, following the procedure de-
scribed below.
IMPORTANTYou are advised to care-
fully read the entire procedure before car-
rying it out.If a mistake is made during the emer-
gency procedure, the ignition key should
be turned to the STOPposition and the
operations must be repeated from the s-
tart (point 1).
1) Read the 5-figure electronic code on
the CODE card.
2) Turn the ignition key to the MAR
position.
3) Fully depress the accelerator pedal
and keep it pressed. The EOBD/fuel sup-
ply-ignition system failure warning light
will come on for eight seconds ap-
proximately and will then go out; now re-
lease the accelerator pedal.
4) The warning light begins to
flash: after it has flashed for the same
number of times as the first digit on the
code of the card, press completely and
hold down the accelerator pedal until the
warning light comes on (for 4 sec-
onds) and then goes out again; now re-
lease the accelerator pedal.
5) The warning light will begin to
flash: after it has flashed for the same
number of times as the second digit on
the code of the CODE card, press com-
pletely and hold down the accelerator
pedal.
U
U
U
U
6) Repeat this procedure in the same
way for the other digits on the CODE card
code.
7) After entering the last figure, keep
the accelerator pedal pressed. The warn-
ing light turns on (for four seconds)
and then goes off; now release the accel-
erator pedal.
8) A quick flash of the warning light
(for appr. 4 seconds) confirms that
the operation has taken place correctly.
9) Start the car turning the ignition key
from the MARposition to the AVV po-
sition without returning the key to the
STOPposition.
Conversely, if the warning light
stays on, turn the ignition key to STOP
and repeat the procedure starting from
point 1).
IMPORTANTAfter emergency start-
ing it is advisable to turn to an Alfa
Romeo Authorized Service, because the
procedure described must be repeated
each time the engine is started.
U
U
U

23
ACTIVATING THE ALARM
When the doors and boot/bonnet lids
are closed and the ignition key is in the
STOPposition (key removed), point the
remote control towards the car and press
the button on the ignition key.
With the exception of some markets the
system sounds a “BEEP”, the hazard
warning lights turn on for appr. three sec-
onds and the door lock is engaged.
Engagement of the alarm is preceded
by a self-diagnosis characterised by a
change in the frequency at which the led
(A-fig. 12) flashes. If an anomaly is
detected the system gives off a further
“BEEP”.Surveillance
When the system has been turned on,
the led (A-fig. 12) on the dashboard
will flash to indicate that the system is in
the surveillance mode.
The led (A) inside the car flashes
throughout the whole time the vehicle is
under surveillance.
IMPORTANT Operation of the elec-
tronic alarm is adapted at the origin to
the regulations of the different countries.
Self-diagnosis and monitoring of
doors and bonnet/boot
If, after the alarm has been activated, a
second acoustic signal is heard, check
that all the doors and bonnet/boot are
closed properly and engage the system
once again.
On the other hand, if a door or bon-
net/boot lid is not correctly closed it will
not be controlled by the system.
If the control signal is repeated when
the doors and bonnet/boot are closed
properly this means that the self-diagno-
sis function has detected a system operat-
ing fault, in which case it is necessary
contact Alfa Romeo Authorized Services.
DEACTIVATING THE ALARM
To deactivate the alarm press the button
on the remote control. The system per-
forms the following (with the exception
of some markets):
– the direction indicators turn on twice
briefly
– two beeps are sounded briefly by the
siren
– the doors are released.
IMPORTANT If the led in the car s-
tays on when the system has been deac-
tivated, (maximum of 2 minutes or until
the ignition key is moved to MAR) the
following should be borne in mind:
– if the led stays on permanently, it
means that the remote control batteries
are flat and need replacing;
– if the led continues to flash, but at
different intervals than normal, it means
that attempts to steal the car have been
made, counting the number of flashes it
is also possible to identify the type of at-
tempt:
1 flash: right front door
2 flashes: left front door
fig. 12
305PGSm

24
3 flashes: right rear door
4 flashes: left rear door
5 flashes: volumetric sensors
6 flashes: bonnet
7 flashes: boot
8 flashes: tampering with car starting
cables
9 flashes: tampering with battery cables
or cutting emergency key cables
10 flashes: at least three causes of alarm.WHEN THE ALARM IS
TRIGGERED
When the alarm is engaged it will sound
when:
– One of the doors, the bonnet or the
boot is opened.
– The battery is disconnected or the
electric cables are cut, or the emergency
key cables are cut.
– Intrusion into the passenger compart-
ment, e.g. window being broken (volu-
metric protection).
– Attempt to start the engine (key at
MAR).
Depending on the markets, the trigger-
ing of the alarm will activate the siren
and the hazard warning lights (for about
26 seconds). The methods of operation
and the number of cycles may vary de-
pending on the versions/markets. How-
ever a maximum number of cycles is fore-
seen. Once the alarm cycle has come to
an end the system will return to its nor-
mal monitoring state.
SWITCHING OFF THE ALARM
To switch off the alarm, press the re-
mote control button on the key. If the
alarm does not turn off due to a flat re-
mote control battery or system fault,
open the door after unlocking with the
lock key, then place the key in the igni-
tion switch and turn it to MAR.
To turn on the alarm again, turn the key
toSTOPand remove it, then press the
remote control button after leaving the
car and shutting the doors. If the alarm
does not turn on and the led on the re-
mote control gives only one brief flash
while the led on the dashboard stays on
glowing steadily for about 2 minutes, the
key battery should be replaced by a new
one of the equivalent type on sale c/o
normal retailers. To change the battery
follow the instructions given at paragraph
“Key battery change” on previous pages.
If it is not possible to switch on the
alarm with a new remote control battery,
contact Alfa Romeo Authorised Services
to have the system checked.

26
MINISTERIAL
HOMOLOGATIONS
In keeping with the laws in force in
each country on the subject of radio fre-
quency, we point out that:
– the separate homologation numbers
for each market are given on the last
pages of this handbook before the alpha-
betical index (for some countries also ho-
mologation document);
– for markets in which the transmitter
needs to be marked with the homologa-
tion number, this has been stated on the
component.
(Depending on the versions/markets,
the code may also be marked on the
transmitter and/or on the receiver).
REMOTE CONTROL
DOOR LOCKING
SYSTEM
The system comprises a receiver and a
transmitter (remote control) incorporated
in the key (B-fig. 14). To lock/unlock
the locks, point the transmitter towards
the car, press and release the button
(C). If, when pressing the remote control
push-button (C), the led (A) (where re-
quired) issues just a short flash, replace
the batteries as described in the “The Al-
fa Romeo CODE system” paragraph.
IMPORTANT Should it be necessary
to programme additional remote controls,
contact Alfa Romeo Authorized Services.
IGNITION DEVICE
THE SWITCH (fig. 15)
The switch has four positions:
–STOP: engine switched off, key can
be removed, engine lock engaged, steer-
ing lock engaged, all services excluded a-
part from those powered directly (e.g.
hazard warning light I.C.S. system (ex-
cept climate control).
–ACC: position for using the cigar
lighter and of the I.C.S. system (except
climate control).
–MAR: drive position. The engine
lock is deactivated and all electrical de-
vices are powered.
fig. 14
1015PGSm
fig. 15
1004PGSm