key Alfa Romeo 4C 2021 Instructieboek (in Dutch)

73
IMPORTANT With the car running, the
request is accepted and executed if the
car speed drops below 3 km/h within 3
seconds from the request: if the request
is not executed, the system will maintain
the gear engaged or, if the speed of the
car drops below 10 km/h, will put the
transmission in neutral (N) and the
manoeuvre will have to be repeated.
ENGAGING NEUTRAL (N)
With car stationary and ignition key at
MAR (irrespective of the condition of the
engine), neutral (N) can only be engaged
with the brake pedal pressed.
If the car is in motion, neutral (N) can
always be engaged, irrespective of the
pressure applied to the brake and
accelerator pedals.
The display will show the letter N
together with the active operating mode.To engage a speed from the neutral (N)
position, press button 1 on the gearbox
panel (it is not necessary to press the
brake pedal):
the gearbox will immediately choose the
correct gear according to the vehicle’s
speed.
With car stationary and ignition key at
MAR (irrespective of the condition of the
engine), 1
stgear can only be engaged with
the brake pedal pressed.
LAUNCH CONTROL
The “Launch Control” strategy permits
high-performance starting.
This strategy can be activated with
vehicle at a standstill, “Race” mode
selected and 1st gear engaged.
The sequence of operations to perform is
as follows:
❒ press the brake pedal and hold it
down;
❒ press the accelerator pedal and hold it
down;
❒ press the “–” paddle behind the
steering wheel;The car will start off at maximum
acceleration when the brake pedal is
released.
Keeping the accelerator pressed, the
system will automatically upshift once
the best engine speed has been achieved
for shifting gears.
78)
To abandon the strategy, simply interrupt
the above sequence of operations or
release the accelerator pedal.
DISPLAYED INFORMATION
When the key is turned to MAR-ON, after
about 1 second, the display shows the
transmission in neutral indication (N).
When driving, the display shows the gear
engaged and the active mode (AUTO or
MANUAL). The indications on the display
have the following meanings:
N = neutral;
1 = first gear;
2 = second gear
3 = third gear;
4 = fourth gear;
5 = fifth gear;
6 = sixth gear;
R = reverse.

STARTING AND DRIVING
74
The car always starts in neutral. When
1st gear is requested, the system forces
the selection of AUTO mode.
IMPORTANT If 10 seconds elapse with
the ignition key in the MAR position and
the display does not show the gear
engaged, turn the key to the STOP
position, wait for the display to go out
and then repeat the manoeuvre.
If the fault persists, contact a dedicated
Alfa Romeo Dealership.
ACOUSTIC SIGNAL
For safety reasons, there is a buzzer
warning when parking the car with the
gearbox in neutral (N) (the warning is
heard when the ignition key is turned to
the STOP position).
With the vehicle stationary, the engine
started and (1st) or (R) engaged, the
system activates the buzzer and
automatically put the gearbox in neutral
(N) when:
❒ the accelerator and/or the brake
pedal are not operated for at least 3
minutes;
❒ the brake pedal is pressed for longer
than 10 minutes;❒ the driver’s door is opened and the
accelerator pedal or the brake pedal are
not operated for at least 1.5 seconds;
❒ a fault is detected in the gearbox.
PARKING THE CAR
When parking and leaving the car,
proceed as follows:
❒ engage the gear (on a slope, engage
first gear if the vehicle is facing uphill or
reverse if it is facing downhill) and leave
the wheels steered;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
IMPORTANT: NEVER leave the car with
the transmission in neutral.
IMPORTANT NOTES
❒ With car stationary and gear engaged,
always keep the brake pedal pressed
until you decide to set off, then release
the brake and accelerate gradually.
❒ During prolonged stops with the
engine running, it is advisable to keep the
gearbox in neutral (N).❒ In order to safeguard the efficiency of
the clutch, do not use the accelerator to
keep the car stationary (e.g. when
stopped on an incline). Clutch overheating
could damage it:
use the brake pedal instead or the
handbrake and only press the accelerator
pedal when you wish to set off.
❒ If, with reverse gear (R) engaged, you
have to engage 1st gear or vice versa,
only do this when the car is completely
stationary and with the brake pedal
pressed.
❒ Although it is strongly discouraged, if
you are going downhill and for unknown
reasons you let the car move forward
with the gearbox in neutral (N), when
there is a request to engage a gear the
system will automatically engage the
best gear in relation to the speed of the
actual to allow the correct transmission
of the drive torque to the wheels;.

75
❒ When necessary, with the engine
switched off, it is possible to engage the
1st speed, reverse (R) or neutral (N) with
key in MAR position and brake pressed.
In this case, gear shifts must be made
allowing at least 5 minutes to elapse
between one gear shift and the next to
safeguard the operation of the hydraulic
system and the pump in particular.
❒ For uphill departures, it is advisable to
accelerate gradually but fully
immediately after releasing the
handbrake or the brake pedal;
this allows the engine to temporarily
increase the number of revs and tackle
the steepest gradients with more torque
at the wheels.CRUISE CONTROL
(where provided)
This is an electronically controlled driving
assistance device that allows the desired
vehicle speed to be maintained, without
having to press the accelerator pedal.
This device can be used at a speed above
30 km/h on long stretches of dry, straight
roads with few variations
(e.g. motorways).
It is therefore not recommended to use
this device on extra-urban roads with
traffic. Do not use it in town.
ACTIVATING THE DEVICE
Turn ring 1 fig. 48 to .
48A0L0022
78)The Launch control function is only
available in Race mode. Regardless of
what is explicitly indicated in the
description of these modes, the ESC and
ASR systems are deactivated during
operation of the Launch Control function.
This means that vehicle dynamic control
is the sole responsibility of the driver.
Therefore pay the utmost attention when
using the Launch Control. Take into
account traffic and road surface
conditions and during manoeuvres make
sure there is enough room in the area
concerned.
IMPORTANT
The cruise control cannot be engaged in
1st or reverse gear: it is advisable to
engage it in 5th gear or higher.
When travelling downhill with the device
engaged, the car may slightly exceed the
stored speed.
When the device is activated, the
digital warning light switches on together
with the relevant message on the display.
SETTING THE DESIRED SPEED
Proceed as follows:
❒ turn ring nut 1 fig. 48 to and press
the accelerator to reach the desired
speed;
❒ move the stalk upwards (+) for at least
1 second, then release it: the car speed is
now stored and you can therefore release
the accelerator.
If needed (when overtaking for instance),
you can accelerate simply by pressing the
accelerator; when you release the pedal,
the car goes back to the speed stored
previously.

89
Protected deviceAmpereFuse
Headlight beam changeover switch (where provided) F09 5
One-tone horn F10 10
12V socket / cigar lighter F86 15
Door mirror defrosters F88 7.5
Dashboard fuse box fig. 114
Protected deviceAmpereFuse
Central locking F38 15
Two-way windscreen washer pump F43 20
+30 Driver side electric windows F47 20
+30 Passenger side electric windows F48 20
Engine compartment fuse box, fig. 116
90)If a fuse blows again, contact a dedicated Alfa Romeo Dealership.
91)Never replace a fuse with another with a higher amp rating; RISK OF FIRE.
92)If a general protective fuse (MAXI-FUSE, MEGA-FUSE, MIDI-FUSE) blows, contact a dedicated Alfa Romeo Dealership.
93)Before replacing a fuse, make sure the ignition key has been removed and that all the other services are switched off and/or disengaged.
94)Contact a dedicated Alfa Romeo Dealership if a safety system (airbags, brakes), transmission system (engine, gearbox) or steering system
general protection fuse blows.
IMPORTANT
10)Never replace a blown fuse with metal wires or other material.
11)If you need to wash the engine compartment, take care not to aim the jet of water directly at the fuse box.
WARNING

99
After a collision, turn the ignition key to
STOP to prevent the battery from
running down.
To restore the correct operation of the
car, proceed as follows:
❒ bring the left exterior light control
stalk to central position (neutral);
❒ turn the ignition key to MAR;
❒ activate the right direction indicator;
❒ deactivate the right direction
indicator;
❒ activate the left direction indicator;
❒ deactivate the left direction indicator;
❒ activate the right direction indicator;
❒ deactivate the right direction
indicator;
❒ activate the left direction indicator;
❒ deactivate the left direction indicator;
❒ ignition key turned to the OFF
position;
❒ turn the ignition key to MAR.TOWING THE VEHICLE
The tow hook provided with the car is
located in the tool box in the luggage
compartment.
The tow hook attachment is only
available at the front end of the car.
ATTACHING THE TOW RING
Take tow hook 1 fig. 86 and tighten it
fully onto the threaded pin.
113) 114) 115)
86A0L0107
112)If, after an impact, you smell fuel or
notice leaks from the fuel system, do not
reactivate the system to avoid the risk of
fire.
IMPORTANT

IN AN EMERGENCY
100
113)Before towing, turn the ignition key
to the MAR position and then to STOP
without removing it. The steering column
will automatically lock when the key is
removed and the wheels cannot be
steered. Also check that the transmission
is in neutral (N).
114) When towing, remember that the
assistance of the brake servo is absent.
Consequently, more force is required at
the pedal in order to brake. Do not use
flexible cables when towing and avoid
jerky movements. Make sure not to
damage parts in contact with the car
while towing.
When towing the vehicle, you must
comply with all specific traffic
regulations and adopt an appropriate
driving behaviour.
Do not start the engine while towing the
car. Before tightening the ring, clean the
threaded housing thoroughly. Make sure
that the ring is fully fastened in the
housing before towing the vehicle.
IMPORTANT115) The tow hook should be used only
for emergencies on the road. You are
allowed to tow the vehicle for short
distances using an appropriate device in
accordance with the highway code (a rigid
bar), to move the vehicle on the road in
readiness for towing or transporting via a
breakdown vehicle.
Tow hooks MUST NOT be used to tow
vehicles off the road or where there are
obstacles and/or for towing operations
using cables or other non-rigid devices.
In compliance with the above conditions,
towing must take place with the two
vehicles (one towing, the other towed)
aligned as much as possible along the
same centre line.

SERVICING AND CARE
112
Lifting blade
If it is necessary to lift the blade from the
windscreen (e.g. in the event of snow or if
the blade needs replacement) proceed as
follows:
❒ by turning the ring nut 1 fig. 96 to
;
❒ turn the ignition key to MAR and then
to STOP;
❒ after turning the ignition key to STOP,
within 2 minutes move the right stalk
upwards, into unstable (“anti-panic”)
position, for at least half a second. The
windscreen wiper then executes part of a
stroke; at each command, approximately
1/3 of a normal wiper stroke is triggered.
❒ the previous operation can be
repeated up to 3 times, in order to move
the blade to the most suitable position;
❒ lift the blade from the windscreen and
proceed with the required operation;
96A0L0021
❒ lower the blade, bringing it into
contact with the windscreen;
❒ bring the blade to the initial rest
position, turning the ignition key to MAR.
20)
Replacing the front windscreen wiper
blade
Proceed as follows:
❒ lift the windscreen wiper blade,
following the instructions given
preciously;
❒ press tab 1 fig. 97 of the attachment
spring and remove the blade from the
arm;
❒ fit the new blade, inserting the tab in
the dedicated housing in the arm and
checking that it is locked;
AIR FILTER
For cleaner replacement, contact a
dedicated Alfa Romeo Dealership.
WINDSCREEN WIPER
It is advisable to replace the blade about
once a year.
125)
A few simple precautions can reduce the
possibility of damage to the blade:
❒ if the temperature falls below zero,
make sure that ice has not frozen the
rubber to the glass.
Use an antifreeze product to release it if
required;
❒ remove any snow from the glass;
❒ do not operate the windscreen wiper
on dry glass.
IMPORTANT Do not lift the arm of the
windscreen wiper when it is in its initial
rest position. Refer to the following
instructions to lift the windscreen wiper
blade correctly.

117
IMPORTANT The washing should take
place with the engine cold and the
ignition key in the STOP position.
After the washing operation, make sure
that the various protections (e.g. rubber
caps and guards) have not been removed
or damaged.
6)Detergents pollute water. Only wash
your vehicle in areas equipped to collect
and treat wastewater from this type of
activity.
WARNING
24)In order to preserve the aesthetic
appearance of the paint abrasive
products and/or polishes should not be
used for cleaning the car.
25)Avoid washing with rollers and/or
brushes in washing stations. Wash the
vehicle only by hand using neutral pH
detergents; dry it with a wet chamois
leather. Abrasive products and/or
polishes should not be used for cleaning
the vehicle. Bird droppings must be
washed off immediately and thoroughly
as the acid they contain is particularly
aggressive. Avoid (if at all possible)
parking the vehicle under trees; remove
vegetable resins immediately as, when
dried, it may only be possible to remove
them with abrasive products and/or
polishes, which is highly inadvisable as
they could alter the typical opaqueness of
the paint. Do not use pure windscreen
washer fluid for cleaning the front
windscreen and rear window; dilute it min.
50% with water. Only use pure screen
washer fluid when strictly necessary due
to outside temperature conditions.
IMPORTANT
INTERIOR
130) 131)
Periodically check the cleanliness of the
interiors, beneath the mats, also to
prevent damage to carbon parts.
To remove and reposition the mats in the
passenger compartment, proceed as
follows:
❒ undo the screws with folding ring 1
fig. 103, driver side and passenger side;
❒ separate the Velcro fabric strips 2 in
the front area under the mats, lifting
them from the floor.
Reposition the mats on the floor, making
sure that the holes at the back of the
mats coincide with the screw housings on
the floor.
103A0L0143

ALPHABETICAL INDEX
150
marking .....................................................121
specifications.........................................119
Engine compartment ................................106
checking levels ......................................106
washing .....................................................116
Engine coolant .............................................108
Engine coolant gauge ...................................30
Engine number..............................................121
Engine oil consumption............................108
level check ...............................................108
ESC (Electronic Stability Control)
system .................................................................51
Exterior light bulbs replacement ...........84
Exterior lights .................................................16
Filling the tank ................................................79
Fitting universal child seat .......................61
Fix&Go Automatic.........................................94
Flashing the headlights ..............................17
Fluids and lubricants
(specifications) ...........................................130
Follow Me Home device .............................17
Front airbag driver’s side ...........................64
Front light clusters
(changing a bulb) .............................................84
Fuel consumption ......................................132
Fuel cut-off system ......................................98
Fuel gauge .........................................................30
Fuse replacement .........................................87
Gear Shift Indicator .....................................32
Getting to know your car ..............................7
Handbrake ........................................................69
Hazard warning lights ..................................82
HBA system ......................................................50
Headlights .........................................................25
adjusting headlights abroad .............25
light beam direction ...............................25
Headlights (bulb replacement) ...............84
Heating and ventilation ..............................20
Heavy-duty use of the car ......................105
Hill Holder system .........................................51
Identification data ....................................120
chassis number......................................121
engine marking ......................................121
identification data plate ..................120
paintwork identification plate.......121
Ignition device .................................................10
steering wheel lock ................................11
In an emergency ..............................................81
Interior lights....................................................18
Interiors (cleaning) ....................................117
Jack ......................................................................90
Jump starting ...................................................97
Keys.........................................................................9
key with remote control ................................9
mechanical key ............................................9Kit Fix&Go Automatic .................................94
Knowing the instrument panel ................29
Load limiters ...................................................60
Lubricants (specifications) ....................130
Main beam headlights ................................17
bulb replacement ....................................84
Main beam headlights .................................17
bulb replacement ....................................82
Maintenance and care .............................101
bodywork..................................................115
heavy-duty use of the car ................105
regular checks .......................................106
scheduled servicing plan .................103
scheduled servicing ............................102
Manual climate control ...............................21
Menu options ..................................................34
Mirrors.................................................................15
Number plate lights
(bulb replacement) ........................................87
On-board instruments ...............................30
display...................................................30/32
engine coolant gauge.............................30
fuel gauge ...................................................30
speedometer .............................................30
tachometer .................................................30