change wheel Alfa Romeo 4C 2021 Instructieboek (in Dutch)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2021, Model line: 4C, Model: Alfa Romeo 4C 2021Pages: 156, PDF Size: 3.06 MB
Page 57 of 156

55
OperationSensor presence on wheel
installed on vehicleFault indicationAction needed
–
Wheel replacement with
winter tyres
Wheel replacement wit
winter tyres
Wheel replacement with others of
different size (*)–
NO
YES
YESYES
SI
NO
NOContact a dedicated Alfa Romeo
Dealership
Contact a dedicated Alfa Romeo
Dealership
–
–
(*) Shown as an alternative in the Owner Handbook or on the registration certificate;
available at Lineaccessori Alfa Romeo. In order to use the system properly, refer to the following table when you have to change wheels/tyres:
Page 58 of 156

SAFETY
56
43)The presence of the TPMS does not
permit the driver to neglect regular
checks of the tyre pressure, including for
the spare wheel.
44)Tyre pressure must be checked with
tyres rested and cold. Should it become
necessary for whatever reason to check
pressure with warm tyres, do not reduce
pressure even though it is higher than the
prescribed value. Repeat the check when
the tyres are cold.
45)Should one or more wheels be fitted
without sensors, the system will no longer
be available and, in addition to the TPMS
warning light flashing for less than one
minute before becoming constant, a
warning message will be shown on the
display, until 4 wheels with sensors are
fitted again.
46)The TPMS cannot warn of sudden
decreases in tyre pressure (for example
when a tyre bursts). In this case, stop the
car, braking with caution and avoiding
abrupt steering.
47)Replacing standard tyres with winter
tyres (and vice versa) requires TPMS
adjustment that must only be performed
by a dedicated Alfa Romeo Dealership.
IMPORTANT48)Changes in outside temperature may
cause tyre pressures to vary. The TPMS
system may temporarily indicate
insufficient pressure. In this case, check
the tyre pressure when cold and, if
necessary, restore the inflation values.
49)When a tyre is removed, it is
advisable to replace the rubber valve seal
as well: contact a dedicated Alfa Romeo
Dealership. Tyre and/or rim
fitting/removal operations require
specific precautions; to avoid damaging
or fitting the sensors incorrectly, tyre
and/or rim fitting/removal operations
should only be carried out by specialised
staff. Contact a dedicated Alfa Romeo
Dealership.
50)Strong radio-frequency interference
could inhibit the regular operation of the
TPMS. This condition will be indicated by
a message on the display. The message
will disappear automatically as soon as
the radio-frequency interference ceases
to affect the system.51)The tyre repair kit (“Fix&Go
Automatic”) provided with the car (where
provided) is compatible with the TPMS
sensors; using sealants not equivalent
with that in the original kit may adversely
affect its operation. If sealants not
equivalent with the original one are used,
it is recommended to have the TPMS
sensors checked by a qualified repair
centre.
Page 72 of 156

STARTING AND DRIVING
70
TCT TWIN CLUTCH
TRANSMISSION
Alfa 4C features the TCT 6-speed twin
dry clutch transmission with steering
wheel controls. This is an advanced
technical solution which combines the
control of a manual gearbox, the
immediacy of a sequential system and
the convenience of being able to select an
automatic selection programme without
the slowdown of a conventional
automatic transmission.
With the key removed from the ignition,
the system will not implement any action
when the buttons on the transmission
control panel on the central tunnel fig. 43
are pressed, irrespective of the pressure
applied to the brake pedal.
43A0L0067
Therefore, the transmission will remain in
the condition that it was in when the
engine was switched off.
With car stationary and key at MAR
(ignition-operated electrical services
activated), the screen displays the gear
engaged and the active operating mode
(automatic = AUTO or manual = no
display).
OPERATING MODE
The transmission can operate in two
operating modes (except when the “Race”
mode is selected):
❒ the first manual type (MANUAL), in
which the driver decides directly when to
change gear;
❒ the second completely automatic
(AUTO), in which the system decides
when to change gear.
When the “Race” mode is selected, the
only allowed operating mode is MANUAL.
Manual operation (MANUAL)
In this operating mode, the driver is
responsible for choosing the best gear
ratio to engage, depending on the car
operating conditions.Use the “+” steering wheel stalk to
engage a higher gear, or the “–” stalk to
engage a lower gear (see the following
paragraph, “Steering wheel stalks”).
If the request is accepted by the system,
the display shows the new gear engaged.
If the request is not accepted by the
system, the display shows the gear
engaged before the request and emits an
acoustic signal.
If the gear change request may adversely
affect the correct operation of the engine
and the transmission, the system will not
allow it.
44A0L0146
Page 74 of 156

STARTING AND DRIVING
72
The shifting up or down is only permitted
if the engine revs allow it.
STARTING THE ENGINE
To start the engine press the brake pedal:
the system engages neutral (N)
automatically.
After the starting procedure, 1st gear (1)
or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear or
reverse (R), it is necessary to press the
brake pedal and press the 1 button on the
transmission control panel (or the “+”
steering wheel stalk) to engage 1st gear
or the R button to engage reverse.
When 1st gear is engaged, the system
sets itself to AUTO mode.
Neutral (N) can be engaged again by
pressing the N button with the brake
pedal pressed.
When the 1, N or R buttons are pressed
(or “+” steering wheel stalk is operated)
without pressing the brake pedal, no gear
change request is implemented by the
system.
IMPORTANT Reverse cannot be engaged
by pressing the “-” stalk on the steering
wheel.
Important notes
To start in presence of a gearbox fault
(see “Warning lights and messages”
paragraph in the “Knowing the instrument
panel” chapter), run the
“Delayed start-up” procedure:
turn the key to the AVV position for at
least 7 seconds with the brake depressed
and the engine will start.
The system will remain in “recovery”
condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver’s door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.It is not possible to set off in a higher gear
than 1st: if this is attempted, the display
shows a dedicated message.
When setting off on a medium-steep
incline, it is advisable to engage the
handbrake.
Engaging 1st gear
Proceed as follows:
❒ press the brake pedal;
❒ press the 1 button on the
transmission control panel;
❒ release the brake pedal and press the
accelerator pedal.
Engaging reverse (R)
Reverse (R) can only be engaged with car
stationary and brake pedal pressed.
Proceed as follows:
❒ press the brake pedal (car completely
stationary);
❒ press button R on the
gearbox panel;
❒ release the brake pedal and press the
accelerator pedal.
When reverse is engaged on some
versions, the system emits an acoustic
signal.
If the brake pedal is not depressed (and
the vehicle is stationary), the display will
show a dedicated message and the
system will automatically engage neutral
(N).
Page 87 of 156

85
DIRECTION INDICATORS
Front
To replace the bulb, proceed as follows:
❒ steer the wheel completely;
❒ open the protective flap 1 fig. 56 by
rotating the fixing screw;
❒ take out the electric connector
1 fig. 58 and then rotate the bulb holder 2
clockwise and remove it;
❒ remove the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector 1;
❒ close the protective flap 1 fig. 56.
58A0L0094
Side
To replace the bulb, proceed as follows:
❒ operate the lens 1 fig. 59 in the point
shown to press in the internal clip,
❒ then pull the unit outwards; turn the
bulb holder 2 anticlockwise, remove the
bulb and replace it;
❒ refit the bulb holder 2 in the lens and
turn it clockwise;
❒ refit the cluster making sure that the
internal clip clicks into position.
59A0L0095
REAR LIGHT CLUSTERS
Contain the bulbs for the direction
indicators, side lights and brake lights.
DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒ remove the protective cap 1 fig. 60
(one on each side) located on the side
boot lining;
60A0L0096
Page 92 of 156

IN AN EMERGENCY
90
CHANGING A WHEEL
GENERAL INSTRUCTIONS
For some specific markets, the car may
be equipped with a space-saver spare
wheel: see the instructions on the
following pages for changing the tyre.
95) 96) 97) 98) 99)
JACK
Please note that:
❒ the weight of the jack is
approximately1.7 kg;
❒ the jack requires no adjustment;
❒ the jack cannot be repaired: in the
event of a fault it must be replaced by
another original one;
❒ no tool other than its operating rod
may be fitted on the jack.
Jack maintenance
❒ prevent any dirt from depositing on
the “worm screw”;
❒ keep the “worm screw” lubricated.
❒ never modify the jack.
Conditions in which not to use the jack
❒ temperatures lower than – 40°C;
❒ on a sandy or muddy ground;
❒ on uneven ground;
❒ on a road with steep gradient;
❒ in extreme weather conditions:
❒ thunderstorms, typhoons, hurricanes,
blizzards, storms, etc.
❒ in direct contact with the engine or for
working underneath the car;
❒ on boats.
To change a wheel, proceed as follows:
❒ stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely.
The ground must be flat and sufficiently
compact;
❒ switch off the engine, pull up the
handbrake and engage the 1st gear or
reverse. Wear the reflective safety jacket
(compulsory by law) before getting out of
the vehicle;
❒ take the space-saver wheel;
❒ access the luggage compartment and
take the wheel replacement kit fig. 69;❒ take the spanner 1 fig. 70 from the kit
and loosen the fixing stud bolts by about
one turn. swing the car laterally to make it
easier to separate the rim from the wheel
hub;
❒ position the jack under the car near
the wheel to be replaced, near the
references on the side skirts;
69A0L0182
70A0L0183
Page 95 of 156

93
At the end of the operation
Proceed as follows:
❒ reposition the space-saver wheel;
❒ place the jack and the other tools in
the container;
❒ arrange the container and tools in the
luggage compartment.
95)The space-saver wheel (where
provided) is specific to your vehicle: do
not use it on other models, or use the
space-saver wheel of other models on
your vehicle. The space-saver wheel must
only be used in the event of an emergency.
Never use it for more than strictly
necessary and never exceed 80 km/h. On
the space-saver wheel there is an orange
label, summarising the main warnings
regarding space-saver wheel usage
restrictions. Never remove or cover the
label. The label contains the following
indications in four languages: “Warning!
For temporary use only! 80 km/h max.!
Replace by standard wheel as soon as
possible. Never cover this indication”.
IMPORTANT
96)Use your hazard lights, warning
triangle, etc. to show that your car is
stationary in compliance with regulations.
Passengers should get out of the car,
particularly if it is heavily loaded, and
wait for the wheel to be changed away
from the traffic. On hills or uneven roads,
use chocks or appropriate objects to
block the wheels of the vehicle.
97) The vehicle’s driving characteristics
will be modified with the space-saver
wheel fitted. Avoid violent acceleration
and braking, abrupt steering and fast
cornering. The overall duration of the
space-saver wheel is about 3000 km,
after which the relevant tyre must be
replaced with another one of the same
type. Never install a standard tyre on a
rim that is designed for use with a space-
saver wheel. Have the wheel repaired and
refitted as soon as possible. Using two or
more space-saver wheels at the same
time is forbidden.
Do not grease the threads of the stud
bolts before fitting them: they might slip
out when driving!98) The jack is a tool developed and
designed only for changing a wheel, if a
tyre gets punctured or damaged, on the
vehicle with which it is supplied or on
other vehicles of the same model.
Any other use, e.g. to jack up other vehicle
models or different things, is strictly
prohibited. Never use it to carry out
maintenance or repairs under the vehicle
or to change summer/winter wheels and
vice versa. Never position yourself under
a jacked vehicle. If any work under the
vehicle is necessary, contact the Alfa
Romeo Service Network. Incorrectly
positioning the jack may cause the vehicle
to fall: use it only in the positions
indicated. Do not use the jack for loads
higher than the one shown on its label.
Never start the engine with vehicle raised.
If the vehicle is raised more than
necessary, everything can become more
unstable, with the risk of the vehicle
dropping violently. Thus, lift the vehicle
only as needed in order to access the
spare tyre.
99) The space-saver wheel cannot be
fitted with snow chains.
Page 151 of 156

149
ALPHABETICAL INDEX
ABS system......................................................50
Active safety systems ..........................50
Air cleaner ................................................112
Alarm .............................................................11
Alfa DNA system .....................................27
All Weather mode ...................................28
Dynamic mode ..........................................27
Natural mode .............................................27
Race mode ..................................................27
All Weather mode ...................................28
Alfa Romeo CODE system .................11
Alfa Romeo Code.....................................12
ASR (AntiSlip Regulation) system..50
Battery.............................................................113
recharging ................................................113
replacement ...........................................114
tips for extending battery life ......114
Body cleaning and maintenance..........115
Body paintwork
identification plate ....................................121
Bodywork........................................................115
corrosion warranty .............................115
maintenance ...........................................116
protection against
atmospheric elements ......................115
Boot/bonnet.............................................24/25
opening .........................................................24
closing ..........................................................25Brake (liquid level) ......................................110
Bulb types .........................................................82
Bump starting ..................................................98
Carrying children safely ............................60
CBC (Cornering Brake Control)
system .................................................................51
Changes/alterations to the car..................4
Changing a bulb ..............................................82
Changing a wheel ...........................................90
Chassis number ...........................................121
Checking levels ...........................................106
Child restraint system ........................61/62
Child restraint systems
recommended by Alfa Romeo.................62
Cleaning (outside and inside) ....116/118
engine compartment ..........................116
fabric seats and parts ........................118
genuine leather parts .........................118
headlights ................................................116
interiors.....................................................117
leather seats...........................................118
plastic and coated parts ...................118
windows ....................................................116
Climate control system ..............................20
CO
2emissions .............................................133
Courtesy lights ...............................................18
Cruise Control..................................................75
Dashboard ...........................................................8
Dashboard and on-board
instruments.......................................................30
Daytime running lights (DRL) ...................17
Dimensions ....................................................127
Dipped beam headlights ............................17
bulb replacement ....................................84
Dipped beam headlights ............................17
bulb replacement ....................................82
Direction indicators ......................................17
bulb replacement ....................................82
Display .................................................................32
Door locking .....................................................12
Door mirrors .....................................................15
Door opening/closing ..................................13
Doors ...................................................................12
central locking/unlocking....................12
DTC (Drag Torque Control) system ......50
EBD system .....................................................50
Electronic Q2 system (“E-Q2”) ................51
Emergency starting .....................................97
Engine codes .................................................121
Engine compartment ................................106
engine coolant level ...........................108
engine oil ..................................................130
identification codes ............................120