key Alfa Romeo Giulietta 2010 Owner handbook (in English)

19
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Parking sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will be shown
on the display if a parking sensor fault is detected.
Drive mode display (“Alfa DNA” system)
(for versions/markets, where provided)
On versions equipped with a reconfigurable multifunction display,
a message + symbol associated with the selected driving mode -
“DYNAMIC”, “NORMAL” or “ALL WEATHER” - is shown. A warning
message is shown on the display if one of these driving modes is
not available.
On versions equipped with multifunction display, a letter (d or a)
associated with the selected driving mode is shown together with
a dedicated message.
Rain sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will appear on
the display if a rain sensor fault is detected.u
t
Engine oil level display
(for versions/markets, where provided)
When the ignition key is turned to MAR the display shows, for a
few seconds, the engine oil level. A warning message appears on
the display if the engine oil level is insufficient.
IMPORTANT To determine the correct engine oil quantity, always
check using the marks on the dipstick (see paragraph "Checking
levels" in the "Servicing and maintenance" section).
IMPORTANT For a correct engine oil level indication, perform the
check with the car parked on a level surface.
IMPORTANT To perform the engine oil level reading correctly, af-
ter turning the key to MAR wait for about 2 seconds before start-
ing the engine.
IMPORTANT The engine oil level may increase after a long stop.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 19

20
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DISPLAY
The car may be equipped with a multifunction display/ multi-
function reconfigurable display which, in accordance with the set-
tings made, can display useful information when driving.
With the ignition key removed, the display lights up and shows the
time and total odometer reading (in km or miles) for a few sec-
onds when a door is opened/closed.
MULTIFUNCTION DISPLAY “STANDARD”
SCREEN fig. 6
The following information is shown on the display:
A. Date
B. Odometer (distance covered in km or miles)
C. Driving mode selected using “Alfa DNA” (dynamic control sys-
tem) (for versions/markets, where provided)
– d = Dynamic
– n = Normal
– a = All Weather
D. Time (always displayed, even with the key extracted and the
front doors closed)
E Start&Stop function indicator (for versions/markets, where
provided)
F. Outside temperature
G Gear Shift Indicator (for versions/markets where provided)
H. Headlight alignment position (dipped headlamps on only)
fig. 6A0K1222g
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 20

23
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
WELCOME MOVEMENT
On some versions, the following occurs when the key is turned to
MAR:
❍quick movement (up and down) of the speedometer and rpm
gauge;
❍illumination of graphic symbols/display;
❍an animated graphic representation of the vehicle profile ap-
pears on the display.
Gauge movement
❍If the key is removed from the ignition switch whilst the gauges
are moving, they immediately return to their initial position.
❍Once they have reached the end-of-scale values the gauges rest
on the value indicated by the car.
❍The movement of the gauges stops when the engine is started.
Illumination of graphic symbols/display
A few seconds after the key is inserted, the gauges, graphic sym-
bols and display light up in sequence.
Graphic animation display
When the key is removed from the ignition switch (with the doors
closed), the display remains lit up and shows a graphic animation.
The display illumination is then dimmed gradually until it goes
out completely.
CONTROL BUTTONS fig. 10
Ò▲: To scroll up the screen and the menu options or increase the
displayed value.
“SET ESC”: Briefly press to access the menu and/or go to the next
screen or confirm your choice. Hold down to go back
to the standard screen.
▼: To scroll down the screen and the menu options or decrease
the displayed value.
IMPORTANT Buttons “
Ò▲“and“▼“ activate different func-
tions in the following situations:
❍to scroll the menu options upwards and downwards;
❍to increase or decrease values during settings.
fig. 10A0K0094m
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 23

30
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
First page (information display on home page)
(for versions/markets, where provided)
This function is used to choose the information you would like to
see on the main screen. You can view the date or the trip meter.
To make your choice, proceed as follows:
– briefly press SET ESC button: “First page” will appear on the dis-
play;
– briefly press SET ESC button again to show the display options:
“Date” and “Engine info”;
– press “
Ò▲“ or“▼“ button to select the information you
wish to see on the main page of the display;
– briefly press SET ESC button to go back to the menu screen or
hold the button down to go back to the standard screen without
saving.
When the key is turned to MAR and the initial check stage is over,
the display will show the information selected via the “First page”
menu function.
See radio (audio information display)
This function is used to shows information relating to the car ra-
dio on the display.
– Radio: selected radio station frequency or RDS message, auto-
matic tuning activation or AutoSTore;
– Audio CD, MP3 CDs: track number;
– CD Changer: CD number and track number;
To show the car radio information on the display (on) or not (off),
proceed as follows:
– briefly press the SET ESC button: the display flashes On or Off
depending on the previous setting;
–press“
Ò▲“or“▼“ to select;
– briefly press the SET ESC button to go back to the menu screen
or hold the button down to go back to the standard screen with-
out saving.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 30

33
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Button volume (Button volume adjustment)
With this function it is possible to adjust (to eight levels) the vol-
ume of the acoustic signal sounding when the MENU SET button
is long pressed to exit a sub-menu and return to the standard menu.
To set the desired volume, proceed as follows:
– briefly press the SET ESC button: the previously set volume lev-
el will be displayed;
– press the button + or – to adjust the volume; an acoustic sig-
nal equal to the volume level being selected is sounded during this
adjustment;
– briefly press the SET ESC button to go back to the previous screen
or hold the button down to go back to the standard screen with-
out saving.
On versions with reconfigurable multifunction display, the volume
level is represented by bars.
Belt reminder (Buzzer/reactivation for S.B.R.
signally)
(for versions/markets, where provided)
This function will only be displayed after the S.B.R. system
has been deactivated by an Alfa Romeo Authorised Service Provider
(see “S.B.R. system” in chapter 2).
Ser vice (Ser vice schedule)
With this function is possible to view information on servicing dead-
lines depending on kilometres travelled or daily intervals. The Ser-
vice function also shows the interval (in kilometres or miles) be-
fore the next engine oil change is due.
This information can be consulted as follows:
– briefly press the SET ESC button, which makes the display show
the service interval in km or mi according to the previous setting
(see “Distance measures” paragraph); press the SET ESC button
to return to the menu screen or hold the button down to return to
the standard screen.
IMPORTANT According to the “Planned Maintenance Programme”,
the car must be serviced every 30,000 km (1.4 petrol versions)
or 35,000 km (1750 Turbo petrol and diesel versions). This mes-
sage is displayed automatically when the key is turned to MAR,
from 2,000 km (or equivalent value in miles) when the next ser-
vice is due and is displayed again every 200 km (or equivalent
value in miles). Below 200 km the signals become more frequent.
The indication will appear in kilometres or miles depending on
the unit of measurement settings. When the next scheduled ser-
vice is approaching and the key is turned to MAR, the word Ser-
vice will appear on the display, followed by the number of kilo-
metres or miles left. Contact Alfa Romeo Authorized Services where
the “Planned Maintenance Programme” operations will be per-
formed and the message will be reset.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 33

36
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
TRIP COMPUTER
GENERAL INFORMATION
The Trip Computer displays information on car operation when
the key is turned to MAR. This function is composed by separate
trips, called “Trip A” and “Trip B” which can monitor the entire mis-
sion (journey) in a reciprocally independent manner.
Both trips can be reset (start of a new journey).
“Trip A” is used to display the figures relating to:
– Autonomy
– Distance travelled
– Average consumption
– Current consumption
– Average speed
– Travel time (driving time). With the function“Trip B” is possible to display the figures relating to:
– Distance travelled B
– Average consumption B
– Average speed B
– Journey time B (driving time).
“Trip B” may be turned off (see “Trip B on” paragraph). “Range”
and “Instant consumption” parameters cannot be reset.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 36

39
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
TRIP button 0.00
This is located on the right stalk (fig. 13). With the ignition key
turned to MAR, this button displays the values described above and
resets then before a new mission:
– short press: values display;
– long press: values reset and start of a new mission.
New journey
It begins after a new reset is made:
– “manual” resetting by the user, by pressing the relevant button;
– “automatic” resetting, when the “Trip distance” reaches
99999.9 km or when the “Travel time” reaches 999.59 (999
hours and 59 minutes);
– after each disconnection and subsequent reconnection of the bat-
tery.
IMPORTANT The reset operation when “Trip A” details are being
displayed resets the information associated with this function only.
IMPORTANT The reset operation when “Trip B” details are being
displayed resets the information associated with this function only.
Start trip procedure
With ignition key turned to MAR, carry out the reset operation by
pressing and holding down the TRIP 0.00 button for longer than
2 seconds.
Exit Trip
You can automatically exit the TRIP function once all the values
have been displayed, or by holding the MENU ESC button down
formorethan1second.
fig. 13A0K0096m
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 39

40
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
SYMBOLS
Some components of the car have coloured labels whose sym-
bols indicate precautions to be observed when using this compo-
nent. Under the bonnet there is also a label that summarises all
the symbols.
ALFA ROMEO CODE SYSTEM
This is an electronic engine locking system which increases pro-
tection against attempted thefts of the car. It is automatically ac-
tivated when the ignition key is extracted.
Each key contains an electronic device which modulates the sig-
nal emitted during ignition by an antenna built into the ignition de-
vice. This signal is the ‘password’ which changes at each ignition
and which the control unit uses to recognise the key and enable
ignition.
OPERATION
The Alfa Romeo CODE system control unit sends an acknowl-
edgement code to the engine management control unit to deacti-
vate the inhibitor each time the car is started by turning the igni-
tion key to MAR.
The code is sent only if the Alfa Romeo CODE system control unit
has recognised the code transmitted from the key.
Each time the ignition key is turned to STOP, the Alfa Romeo
CODE system deactivates the functions of the engine management
control unit. Warning light
Ylights up on the instrument panel
if the code is not correctly recognised during ignition.
In this case, turn the key to STOP and then to MAR; if it is still
locked, try again with the other keys that come with the car. If you
are still unable to start the engine contact Alfa Romeo Authorized
Services.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 40

41
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Warning lightYcomes on when driving
❍If the warning lightYturns on, this means that the system
is running a self-test (due for example to a voltage drop).
❍Contact Alfa Romeo Authorized Services if theYwarning light
stays on.
KEYS
CODE CARD(for versions/markets, where provided)
A CODE card fig.14 is provided together with the keys. On the card
you will find a mechanical code A and an electronic code B. Keep
the codes in a safe place, not in the car.
The Electronic components inside the key may be
damaged if the key is subjected to shocks.
fig. 14A0K0008m
A
B
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 41

42
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
MECHANICAL KEY
The metal insert A-fig.15 operates:
❍the ignition switch;
❍the door lock.
fig. 15A0K0047mfig. 16A0K0048m
Press B button fig.16 only with the key away from
your body, especially your eyes and from objects
which could get damaged (e.g. your clothes). Do
not leave the key unattended to avoid the button being
accidentally pressed while it is being handled, e.g. by a
child.
KEY WITH REMOTE CONTROL
(for versions/markets, where provided)
The metal insert A-fig.16 operates:
❍the ignition switch;
❍the door lock.
Press B button to open/close the metal insert.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 42