clutch Alfa Romeo Giulietta 2010 Owner handbook (in English)

REFUELLING
Petrol engines: refuel with unleaded petrol with an
octane rating (RON) of 95 or higher only.
Diesel engines: refuel with diesel fuel compliant with
European specification EN590 only. The use of other products or
mixtures may damage the engine beyond repair and consequently
invalidate the warranty, depending on the damage caused.
STARTING THE ENGINE
Petrol engines: make sure that the handbrake is
engaged, set the gearshift lever to neutral, fully depress the
clutch without pressing the accelerator, then turn the ignition key
to AVV and release it as soon as the engine has started.
Diesel engines: turn the ignition key to MAR and wait for theYandmwarning lights to turn off; turn the key to AVV and release it
as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter reaches high temperatures
during operation. Do not park the car on grass, dry
leaves, pine needles or other flammable material: fire
hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that carries out a
continuous diagnosis of the emission-related components
in order to help protect the environment.
ELECTRIC ACCESSORIES
If after having purchased your car you decide to add
accessories requiring electricity (that may otherwise
cause the battery to gradually lose power), please
contact Alfa Romeo Authorized Services. They can
calculate the overall electric requirement and check that
the car’s electric system can support the required load
CODE CARD(for versions/markets where provided)
Keep this in a safe place, not in the car. We recommend
that you always carry the electronic code provided on
the CODE card with you, in case you need to perform
an emergency start.
SCHEDULED SERVICING
Correct car maintenance is essential to ensure that the
performance, safety features, environmental
friendliness and low running costs stay in tip-top
condition over the years.
THE OWNER HANDBOOK CONTAINS…
... information, tips and important warnings on the
correct use and maintenance of your car over time. Pay
special attention to the symbols
"(personal safety)#(environmental protection)â(car integrity).
READ THIS CAREFULLY
K


001-130 Alfa Giulietta EN 5ed 26-07-2010 16:32 Pagina 2

80
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
INCREASING THE STORED SPEED
Press the accelerator and store the new speed or move the stalk
upwards (+). Each movement of the stalk will correspond to an
increase in speed of about 1 km/h, while keeping the stalk held
upwards the speed will continuously increase.
REDUCING THE STORED SPEED
Deactivate the device and store the new speed or move the stalk
downwards (–) until the new speed is reached. It will then auto-
matically be stored. Each movement of the stalk will correspond
to a reduction in speed of about 1 km/h, while keeping the stalk
held downwards will continuously reduce the speed.
TURNING THE DEVICE OFF
Toturnthedeviceoff:
❍turn the A ring fig. 43 to OFF;
❍stop the engine;
❍press the brake pedal, the clutch or the accelerator; in this
last case the system is not actually turned off but the system
gives priority to the acceleration request. The device still re-
mains active, without the need to press the RES button to re-
turn to the previous condition once acceleration is concluded. When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated,
Ü
light comes on together with the relevant message on the instru-
ment panel (for versions/markets, where provided).
STORING THE SPEED
Proceed as follows:
❍turn A ring fig. 43 to ON and press the accelerator until the
car reaches the desired speed;
❍move the stalk upwards (+) for at least one second, then re-
lease it. The speed is now stored and you can therefore release
the accelerator pedal.
If needed (when overtaking for instance), you can accelerate sim-
ply by pressing the accelerator pedal; when you come off the ped-
al, the car will return to the speed memorised previously.
RESTORING STORED SPEED
If the device was disengaged - for example by pressing the brake
or clutch pedal - the stored speed can be reset as follows:
❍accelerate gradually until reaching a speed approaching the one
stored;
❍engage the gear selected at the time of speed storing;
❍press RES button (B-fig. 43).
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 80

116
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
OPERATING MODES
Engine stopping mode
With the car at a standstill, the engine stops with the gearbox in
neutral and the clutch released.
NOTEThe engine can only be stopped automatically after a speed
of about 10 km/h is reached, to prevent the engine from being
repeatedly stopped when driving at walking pace.
Symbol
Ufig. 81 appears on the display when the engine stops.
Engine restarting mode
Press the clutch pedal to restart the engine.
fig. 81A0K0163m
START&STOP SYSTEM
(for versions/markets, where provided)
The Start&Stop system automatically stops the engine whenever
the car is stationary and starts it again when the driver wants to
move off. This improves the efficiency of the vehicle by reducing
fuel consumption, the emission of harmful gases and noise pollu-
tion.
The system is active every time the engine is started.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:34 Pagina 116

118
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Notes
If the clutch is not pressed, after 3 minutes from the engine stop-
ping, the engine can be restarted only using the ignition key.
In cases when the engine stops and this is not desired, due for
example to the clutch pedal being released sharply with a gear
engaged, if the Start&Stop system is activated, the engine can
be restarted by fully depressing the clutch pedal or by placing the
gear lever in neutral
RESTARTING CONDITIONS
For reasons of comfort, limiting harmful emissions and safety pur-
poses, the power unit can restart automatically without any action
on behalf of the driver if certain conditions are met, including:
❍battery not sufficiently charged;
❍windscreen wipers working at maximum speed;
❍low braking system vacuum, e.g. following the brake pedal be-
ing pressed repeatedly;
❍car in motion, for example when driving on hilly roads;
❍stopping the engine using Start&Stop longer than approxi-
mately 3 minutes;
❍for versions equipped with dual zone automatic climate control
system (for versions/markets, where provided), if an adequate
level of thermal comfort has not been reached or MAX-DEF func-
tion activation;
With gear engaged, the automatic engine restarting is possible on-
ly by fully pressing the clutch pedal. This operation is indicated to
the driver by means of a message on the display and by symbol
Ublinking (the latter for versions/markets, where provided).
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:34 Pagina 118

151
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
STARTING AND DRIVING
STARTING PROCEDURE FOR DIESEL VERSIONS
Proceed as follows:
❍engage the handbrake and place the gearbox in neutral;
❍turn the ignition key to the MAR position: warning lights m
and Yon the instrument panel will light up;
❍wait for the warning lights to go out;
❍press the clutch pedal down to the floor without touching the
accelerator;
❍turn the ignition key to AVV as soon as warning light mgoes
out. Waiting too long will waste the heating work carried out
by the glow plugs. Release the key as soon as the engine starts.
If warning light mblinks for approximately 1
minute after starting or during prolonged crank-
ing, this indicates a fault in the glow plug pre-heat-
ing system. Use the car normally if the engine starts and
go to Alfa Romeo Authorized Services as soon as possible.
It is dangerous to have the engine running indoors.
The engine takes in oxygen and discharges carbon
dioxide, carbon monoxide and other toxic gases.
STARTING THE ENGINE
STARTING PROCEDURE FOR PETROL VERSIONS
Proceed as follows:
❍engage the handbrake and place the gearbox in neutral;
❍press the clutch pedal down to the floor without touching the
accelerator;
❍turn the ignition key to AVV and let it go the moment the en-
gine starts.
IMPORTANT
❍If the engine does not start on the first attempt, turn the igni-
tion key to STOP before repeating the operation.
❍If, when the ignition key is at MAR, the instrument panel warn-
ing light
Yremains on together with warning light U, turn
the key to STOP and then back to MAR; if the warning light
remains on, try with the other keys provided with the car. If
you are still unable to start the engine contact Alfa Romeo Au-
thorized Services.
❍Never leave the ignition key on MAR when the engine is off.
151-160 Alfa Giulietta EN 3ed 13-04-2010 11:46 Pagina 151

154
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
USING THE GEARBOX
To engage the gears, press the clutch pedal down fully and shift
the gear lever into the required position (a diagram is shown
on the knob fig. 111).
To engage 6th gear, operate the lever by pressing it towards the
right in order to avoid engaging 4th gear by mistake. Similar ac-
tion to pass from sixth to fifth gear.
To engage reverse gear (R) from the neutral position, lift up ring
A-fig. 111 and simultaneously move the lever to the left and then
forwards.
IMPORTANT Reverse may be engaged only when the car is at a
standstill.
fig. 111A0K0082m
Press the clutch pedal fully to change gears cor-
rectly. Therefore, the floor area under the pedals
must be clear: ensure that any rubber mats are flat
and do not interfere with the pedals.
Do not drive with your hand resting on the gear
lever, because this pressure, even if light, can wear
out the inner components of the gearbox over
time.
151-160 Alfa Giulietta EN 3ed 13-04-2010 11:46 Pagina 154

156
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DRIVING STYLE
Starting
Do not warm up the engine at low or high revs when the car is
stationary; this causes the engine to warm up more slowly, there-
by increasing fuel consumption and emissions. It is advisable to set
off immediately and slowly, avoiding high revs: this allows the
engine to warm up more quickly.
Unnecessar y actions
Avoid revving up when starting at traffic lights or before stopping
the engine. The latter action, like double-declutching, is unneces-
sary and causes increased fuel consumption and pollution.
Gear selection
Use a high gear when traffic and road conditions allow. Using a
low gear for faster acceleration will increase fuel consumption. In
the same way, improper use of a high gear increases fuel con-
sumption, emissions and engine wear.
Top speed
Fuel consumption considerably increases as speed increases. Keep
your speed as even as possible, avoiding unnecessary braking
and acceleration which cause excessive fuel consumption and in-
creased emissions.
Acceleration
Accelerating violently severely affects consumption and emissions:
acceleration should be gradual and should not exceed the maxi-
mum torque.
CONDITIONS OF USE
Cold starting
Short distances and frequent cold start-ups prevent the engine from
reaching its optimum running temperature. Consequently, both con-
sumption (from +15 to +30% on the urban cycle) and emissions
will increase.
Traffic and road conditions
High fuel consumption is caused by heavy traffic, for instance when
travelling in a queue with frequent use of low gears or in cities with
many traffic lights. Mountain roads and uneven surfaces also have
a negative effect on consumption.
Traffic hold-ups
During prolonged hold-ups (level crossings) the engine should be
switched off.
151-160 Alfa Giulietta EN 3ed 13-04-2010 11:46 Pagina 156

200
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
SCHEDULED SERVICING PLAN
1.4 Turbo Petrol and 1.4 Turbo Multi Air VERSIONS
Thousands of kilometres
Check tyre condition/wear and adjust pressure if required
Check lighting system operation (headlights, direction indicators, hazard lights, passenger
compartment lights, boot lights, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rear window wiper blades
Check condition and wear of front disc brake pads and
operation of pad wear indicator
Check rear disc brake pad condition and wear
Conditions and visual check: bodywork exterior, underbody protection,
pipes and hoses (exhaust - fuel system - braking system),
rubber elements (boots - sleeves - bushes - etc.)
Check cleanliness of bonnet and boot locks,
as well as cleanliness and lubrication of linkages
Check and top up, if required, fluid levels
(engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc)
Check the handbrake lever travel and adjust it, if necessary
Check condition of timing belt
Visually inspect the condition of accessory drive belt(s)
Check exhaust gas emissions 30 60 90 120 150 180
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●● ●●●
●●
●●
●●● ●●●
199-224 Alfa Giulietta EN 5ed 26-07-2010 16:38 Pagina 200

35 70 105 140 175
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●● ●●●
●●
●●
202
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
1750 Turbo Petrol VERSIONS
Thousands of kilometres
Check tyre conditions/wear and adjust pressure if required
Check lighting system operation (headlights, direction indicators, hazard warning lights, passenger
compartment lights, boot lights, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rear window wiper blades
Check condition and wear of front disc brake pads and operation of
pad wear indicator
Check rear disc brake pad condition and wear
Conditions and visual check: bodywork exterior, underbody protection,
pipes and hoses (exhaust - fuel system - braking system),
rubber elements (boots - sleeves - bushes - etc.)
Check cleanness of locks, bonnet and boot and lever
cleanness and lubrication
Check and top up, if required, fluid levels
(engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc)
Check the handbrake lever travel and adjust it, if necessary
Visually inspect the condition of the auxiliary drive belt
Visually inspect the condition of toothed timing belt
199-224 Alfa Giulietta EN 5ed 26-07-2010 16:39 Pagina 202

204
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Thousands of kilometres
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlights, direction indicators, hazard warning lights,
luggage compartment, passenger compartment, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rear window wiper blades
Check condition and wear of front disc brake pads and
operation of pad wear indicator
Check rear disc brake pad condition and wear
Conditions and visual check: bodywork exterior, underbody protection,
pipes and hoses (exhaust - fuel system - braking system),
rubber elements (boots - sleeves - bushes - etc.)
Check cleanliness of bonnet and boot locks,
as well as cleanliness and lubrication of linkages
Check and top up, if required, fluid levels
(engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc)
Check the handbrake lever travel and adjust it, if necessary
Check exhaust fumes/emissions
Visually inspect the condition of the auxiliary drive belt
Check engine control system operation (via diagnostic socket)35 70 105 140 175
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●● ●● ●
●●
●● ●● ●
Diesel VERSIONS
199-224 Alfa Giulietta EN 5ed 26-07-2010 16:39 Pagina 204