sensor Alfa Romeo Giulietta 2010 Owner handbook (in English)

15
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Speed limit exceeded (red)
(for versions/markets, where provided)
The warning light (for versions/markets where pro-
vided) comes on when the speed exceeds 120 km/h.
When the car exceeds the speed limit set in the setup Menu (e.g.
120 km/h), on some versions a message and a symbol are shown
in the display and an acoustic signal is activated.
X
Always drive at a speed appropriate to the traffic
conditions, the weather and the laws in force. The
engine may be turned off while the DPF light is on;
however, repeated interruption of the regeneration process
may result in premature degradation of the engine oil.
For this reason, it is always advisable to wait for the light
to go off before turning off the engine, following the in-
structions appearing above. It is not a good idea to com-
plete DPF regeneration with the vehicle stationary.Generic fault (amber)
(for versions/markets, where provided)
The warning light turns on in the following circumstances:
Contact Alfa Romeo Authorized Services as soon as possi-
ble to eliminate the fault.
Exterior lights fault
See the section on warning light6.
Brake lights fault
See description in the “Brake lights fault” section.
Fuel cut-off
This warning light comes on when the fuel cut-off inertia switch is
triggered. A specific message will be shown on the display.
Start&Stop fault
(for versions/markets, where provided)
The warning light comes on when a fault is detected in the
Start&Stop system.
Rain sensor fault
(for versions/markets where provided)
The warning light comes on when a rain sensor fault is detected.
è
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 15

16
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Parking sensor fault
(for versions/markets where provided)
See the section on warning light
t.
Rain sensor fault
(for versions/markets where provided)
This warning light comes on when a dusk sensor fault is detected.
AFS adaptive lights fault
(for versions/markets, where provided)
The warning light comes on when an AFS adaptive light fault is de-
tected (see “AFS adaptive lights” in this chapter). A specific mes-
sage will be shown on the display.
Anti-pinch system fault
The warning light will come on when an anti-pinch system fault
is detected. A specific message will be shown on the display.
Engine oil pressure sensor fault
The warning light turns on when an engine oil pressure sensor fault
is detected. A specific message will be shown on the display.
Rear fog lights (amber)
The warning light comes on when the rear fog lights
are on. The LED over 4 button will also light up.4
Fog lights (green)
The warning light comes on when the fog lights are
on. The LED over 5 button
5will also light up.5
Side lights (green)
This warning light comes on when the side lights are
turned on.
Follow me home (green)
The warning light comes on (in combination with a message on
the display) when this device is used (see “Follow me home de-
vice” in this chapter).
3
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 16

18
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Rain sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will be shown
on the display if a dusk sensor fault is detected.1
Possible presence of ice on the road
On versions equipped with reconfigurable multifunc-
tion display, a message + symbol will appear when
the outdoor temperature falls to or below 3°C.
On versions with multifunctional display, only the message is shown.
IMPORTANT In the event of outdoor temperature sensor fault, dash-
es are shown on the display instead of the value.√
Fuel cut-off
On some versions the display will show a message +
symbol if the fuel cut-off trips. For the fuel cut-off sys-
tem reactivation procedure see paragraph “Fuel cut-off
system” in this chapter.s
Exterior lights fault
On some versions, a message + symbol will appear
on the display if a fault is detected in one of the fol-
lowing lights:
– daytime lights (DRL)
– sidelights/taillights
– direction indicators
– rear fog lights
– number plate lights.
The fault relating to these lights could be: one or more blown bulbs,
a blown protection fuse or a break in the electric connection.W
Brake lights fault
On some versions, a message + symbol will appear
on the display if a brake light fault is detected. The
fault may be caused by a blown bulb, a blown protec-
tion fuse or an interruption of the electric connection.T
Boot open
On some versions, a message + symbol on the dis-
play are shown when the boot is open.R
Bonnet open
On some versions, a message + symbol on the display
are shown when the bonnet is open.S
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 18

19
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Parking sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will be shown
on the display if a parking sensor fault is detected.
Drive mode display (“Alfa DNA” system)
(for versions/markets, where provided)
On versions equipped with a reconfigurable multifunction display,
a message + symbol associated with the selected driving mode -
“DYNAMIC”, “NORMAL” or “ALL WEATHER” - is shown. A warning
message is shown on the display if one of these driving modes is
not available.
On versions equipped with multifunction display, a letter (d or a)
associated with the selected driving mode is shown together with
a dedicated message.
Rain sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will appear on
the display if a rain sensor fault is detected.u
t
Engine oil level display
(for versions/markets, where provided)
When the ignition key is turned to MAR the display shows, for a
few seconds, the engine oil level. A warning message appears on
the display if the engine oil level is insufficient.
IMPORTANT To determine the correct engine oil quantity, always
check using the marks on the dipstick (see paragraph "Checking
levels" in the "Servicing and maintenance" section).
IMPORTANT For a correct engine oil level indication, perform the
check with the car parked on a level surface.
IMPORTANT To perform the engine oil level reading correctly, af-
ter turning the key to MAR wait for about 2 seconds before start-
ing the engine.
IMPORTANT The engine oil level may increase after a long stop.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 19

24
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
The menu includes the following items:
–MENU
– SPEED BEEP
– HEADLIGHT SENSOR (for versions/markets, where provided)
– RAIN SENSOR (for versions/markets where provided)
– ON/TRIP B DATA
– SET TIME
–SETDATE
– FIRST PAGE (for versions/markets where provided)
– SEE RADIO
–AUTOCLOSE
– MEASURES
–LANGUAGE
– ALERTS VOLUME
– BUTTONS VOLUME
– SEAT BELT REMINDER
– SERVICE
– PASSENGER AIR BAG
– DAY LIGHTS
– COURTESY LIGHTS
–MENUEXIT
NOTE Some menu items are shown on the navigator display in mod-
els equipped with radio-navigation systems (for versions/markets,
where provided).SETUP MENU
The menu comprises a series of items which can be selected us-
ing the “
Ò▲“and“▼“ buttons to access the different se-
lection and setting operations illustrated in the following paragraphs.
Some items also have a sub-menu.
The menu can be activated by briefly pressing the SET ESC but-
ton.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 24

27
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Headlight sensor (Automatic headlight/dusk
sensor sensitivity adjustment)
(for versions/markets, where provided)
This function is used to turn the headlights on or off according to
external lighting conditions.
The dusk sensor sensitivity can be adjusted according to 3 levels
(level 1= minimum sensitivity, level 2= average sensitivity, level
3= maximum sensitivity); the greater the sensitivity set, the less
the external light variation needed to control turning on the lights
(e.g. with a setting on level 3 at sunset the headlights are expected
to come on in relation to levels1 and 2).
Proceed as follows to set:
– briefly press SET ESC: the previously set brightness level flash-
es in the display;
– press “
Ò▲“or“▼“ to select;
– briefly press the SET ESC button to go back to the menu screen
or hold the button down to go back to the standard screen with-
out saving.
Rain sensor (sensitivity adjustment)
(for versions/markets where provided)
This function is used to adjust the rain sensor sensitivity to four
levels.
To set the required sensitivity level, proceed as follows:
– briefly press SET ESC button: the previously set sensitivity level
will flash on the display;
–press“
Ò▲“or“▼“toselect;
– press the SET ESC button to go back to the menu screen or
hold the button down to go back to the standard screen without
saving.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 27

66
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
You can adjust one function automatically and have the automat-
ic system control all the others. The amount of air introduced into
the passenger compartment is not affected by vehicle speed; it is
electronically controlled by a fan. The air temperature is always au-
tomatically controlled according to the temperature shown on the
display (except for when the system is off or in certain conditions
when the compressor is not running).
The system can manually programme and adjuste:
❍air temperature on driver’s/passenger’s side;
❍fan speed (continuous variation);
❍air distribution to 7 positions;
❍climate control compressor enabled;
❍fast demisting/defrosting function;
❍air recirculation;
❍heated rear windscreen;
❍turning the system off.
DESCRIPTION
The automatic dual zone climate control system regulates the tem-
perature in the passenger compartment in two areas. The system
keeps the comfort in the passenger compartment constant and
compensates for variable external conditions.
NOTEThe reference temperature is 22°C for optimal comfort man-
agement.
The automatically controlled parameters and functions are:
❍air temperature delivered to driver/front passenger vents;
❍air distribution to driver/front passenger vents;
❍fan speed (continuous air flow variation);
❍switching the compressor fan on (for cooling/dehumidifying
the air);
❍air recirculation.
All these functions can be manually adjusted by operating the sys-
tem and selecting one or more functions and modifying their pa-
rameters. Automatic control of the manually changed functions will
be suspended: the system will only override your settings for safe-
ty reasons.
Manual selections will always have higher priority over automatic
settings and will be stored until the AUTO button is pressed, except
for the cases in which the system will intervene for particular, safe-
ty-related reasons.
The climate control system uses an average radi-
ating temperature sensor installed under a cover
below the inner rearview mirror. To ensure opti-
mal operation of the climate control system, do not ob-
struct the detection cone of this sensor with any object.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 66

72
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DEMISTING/DEFROSTING
HEATED REAR WINDSCREEN
Press(to turn heated rear windscreen demisting/defrosting func-
tion on (LED on button lit). This function switches off automatically
after about 20 minutes or when the engine is turned off. It is not
switched on automatically the next time the engine is started. For
versions/markets, where provided, pressing the
(button it is al-
so possible to defrost/demist the external rearview mirrors, the heat-
ed windscreen (for versions/markets, where provided) and the heat-
ed spray nozzles (for versions/markets, where provided).
IMPORTANT Do not affix stickers to the inside of the heated rear
windscreen on the heating filaments, to avoid damage that might
cause them to stop working properly.
Humidity sensor(for versions/markets, where provided)
The humidity sensor prevents the windows from misting up. For
full operation, it is advisable to turn the AUTO on (LED N on). When
the outside temperature is low, the system could automatically turn
the compressor on and turn air recirculation off for safer driving.
TURNING THE CLIMATE CONTROL SYSTEM OFF
Pressgbutton (LED on button off):
❍air recirculation is on, thus isolating the passenger compartment
from the outside;
❍the compressor is off;
❍the fan is off.
❍the heated rear windscreen can be switched on or off.
❍the AQS (Air Quality System) function cannot be turned on.
IMPORTANT The climate control system control unit stores the tem-
peratures set before the system was switched off and restores
the same conditions when any button of the system is pressed (ex-
cept for D button).
Press AUTO button to restart the climate control system in fully
automatic mode.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 72

74
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
SIDE LIGHTS AND DIPPED BEAM HEADLIGHTS
With the ignition key turned to MAR, turn A ring fig. 40 to2.The
day lights are switched off and the side lights and dipped beam head-
lights are switched on. The warning light
3in the instrument pan-
el comes on.
PARKING LIGHTS
These lights can be turned on only with the ignition key at STOP
or removed, by turning the ring A-fig. 40 first to
Oand then to
2.
The warning light
3on the instrument panel will come on. Op-
erate the direction indicator stalk to select the side (right or left).
AUTOMATIC LIGHTING CONTROL (AUTOLIGHT)
(Dusk sensor)
(for versions/markets, where provided)
This system consists of an infrared LED sensor combined with a rain
sensor installed on the windscreen. It can detect changes of light
intensity outside the car according to the light sensitivity setting
programmed in the set-up menu: the higher the sensitivity, the low-
er the amount of external light needed to switch the lights on.
Activation
The dusk sensor is activated by turning the A ring fig. 40 to2A.
In this way the side lights and dipped beam headlights are both
switched on automatically according to the outside light level.
EXTERIOR LIGHTS
LEFT STALK fig. 40
The left stalk operates most of the external lights. The external
lights can only be switched on when the ignition key is at MAR.
The instrument panel and the various controls on the dashboard
will come on when the external lights are switched on.
DAY LIGHTS (DRL) “Daytime Running Lights”
With the ignition key turned to MAR and A ring fig.40 turned to
position
Othe day lights are turned on; the other lights remain off.
For day light functions, see the “Menu Items” paragraph in this
chapter. If the function is deactivated, no lights are switched on
when the A ring is turned to position
O.
fig. 40A0K0099m
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 74

75
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
MAIN BEAM HEADLIGHTS
With A ring in position2pull the stalk towards the steering wheel
(stable position). The warning light
1on the instrument panel
will come on. To turn the lights off, pull the stalk again towards
the steering wheel (dipped beam headlights will stay on). It is
not possible to switch on the main beam headlights in fixed mode
if the automatic lighting control system is active.
FLASHINGS
Pull the stalk towards the steering wheel (unstable position) re-
gardless of the position of A ring. The
1warning light will come
on in the instrument panel.
DIRECTION INDICATORS
Put the stalk in the stable position:
❍upward: activation of right direction indicator;
❍downward: activation of left direction indicator.
Lights
¥orÎwill flash on the instrument panel. The direction in-
dicators are switched off automatically when the steering wheel
is straightened.
“Lane change” function
If you want to signal that you are changing lane, hold the left stalk
in the unstable position for less than half a second. The direction
indicator on the selected side flashes five times and then switch-
es off automatically. IMPORTANT The sensor is unable to detect the presence of fog. Un-
der these circumstances, these lights are therefore turned on man-
ually.
When the lights are turned on by the sensor, the fog lights (for ver-
sions/markets, where provided) and the rear fog lights may be
turned on. When the lights are automatically switched off, the front
and rear fog lights (if activated) are also switched off. The next
time the lights are switched on automatically, the fog lights must
be reactivated manually (if required).
With the sensor active, it is possible to flash the headlights but
the main beam headlights cannot be switched on. If you need to
turn these lights on, turn A ring fig. 40 to position
2and turn
the dipped beam headlights on.
When the lights have been activated automatically and are then
switched off by the sensor, the dipped beam headlights are switched
off first, followed by the side lights a few seconds later.
If the sensor is activated but is malfunctioning, the side lights and
dipped beam headlights are switched on independently of the out-
side light level and the sensor fault is indicated on the instrument
panel display. It is also possible to deactivate the sensor and switch
on these light.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:33 Pagina 75