Alfa Romeo GT 2005 Owner handbook (in English)

VEHICLE MAINTENANCE
269
Engine compartment
At the end of the winter the engine com-
partment should be carefully washed,
without directing the jet against electronic
control units. Contact a specialised work-
shop to have this done.
Detergents cause water
pollution. Therefore the en-
gine compartment should
be washed in areas equipped for
collecting and purifying the liquid
used in the washing process.
IMPORTANTThe vehicle should be
washed with the engine cold and the igni-
tion key at STOP. After washing make sure
that the various protections (e.g. rubber
caps and various covers) have not been
damaged or removed. Windows
Use specific products to clean the win-
dows. Use clean cloths to avoid scratching
or altering the transparency of the glass.
IMPORTANTThe inside of the
rearscreen should be wiped gently with a
cloth in the direction of the filaments to
avoid damaging the heating device.
Front headlights
IMPORTANTDo not use aromatic sub-
stances (e.g. petroleum) or ketones (e.g.
acetone) to clean the front headlight plas-
tic transparents.
Never use inflammable
products like fuel oil ether
or rectified petrol for
cleaning inside the car. The elec-
trostatic charges generated when
rubbing to clean may cause fire.
INTERIOR FITTINGS
Periodically check that water is not
trapped under the mats (due to water drip-
ping off shoes, umbrellas, etc.) which
could cause oxidisation on the sheet metal.
CLEANING SEATS AND FABRIC
AND VELVET PARTS
– Use a soft brush or a vacuum cleaner
to remove dust. Velvet is cleaned better if
the brush is moistened.
– Rub the seat with a sponge moistened
with a solution of water and neutral deter-
gent.

VEHICLE MAINTENANCE
270
Do not keep aerosol cans
in the car. They might
explode. Aerosol cans
must never be exposed to a tem-
perature above 50°C. The tem-
perature inside the car exposed
to the sun may go well beyond
that figure.
CLEANING LEATHER SEATS
– Remove dried on dirt with a lightly
moistened chamois leather or cloth with-
out pressing too hard.
– Remove liquid and grease stains with
a dry absorbent cloth without rubbing.
Then wipe with a soft cloth or chamois
leather with water and neutral soap. If the
stain persists, use specific products, care-
fully following the instructions for use.
IMPORTANTNever use alcohol. Make
sure that cleaning products do not contain
alcohol and alcohol derivatives even at
low strength.
STEERING WHEEL/GEAR LEVER
KNOB WITH GENUINE
LEATHER COVERING
These components shall only be cleaned
with water and neutral soap. Never use spir-
it or alcohol-based products.
Before using special products for cleaning
interiors, read carefully label instructions and
indications to make sure they are free from
spirit and/or alcohol-based substances.
If when cleaning the windscreen with spe-
cial glass products, some drops fall on the
leather covering of the steering wheel/gear
lever knob remove them immediately and
then clean with water and neutral soap.
IMPORTANTTake the utmost care
when engaging the steering lock to prevent
scratching the leather covering.
INTERIOR PLASTIC PARTS
Clean plastic parts with a cloth
mositened with water and non-abrasive
neutral detergent. To remove grease or
hard stains, use appropriate products
designed to preserve the appearance of
components.
IMPORTANTNever use spirit or petro-
leum to clean the instrument panel or
other plastic parts.
Upholstery of your car has
been designed to withstand
wear deriving from com-
mon use of the car. You are how-
ever recommended to avoid strong
and/or continuous scratching with
clothing accessories such as metal-
lic buckles, studs, Velcro fastenings
and the like, since these items cause
circumscribed stress of the cover
fabric that could lead to yarn break-
ing, and damage the cover as a con-
sequence.

TECHNICAL SPECIFICATIONS
271
IDENTIFICATION LABEL
This (fig. 2) is to be found on the front
crossmember of the engine compartment.
It contains the following information:
(A)Space for details of national ho-
mologation
(B)Space for punching the consecutive
chassis number
(C)Space available for maximum
weights authorised by various na-
tional regulations
(D)Space for version and any supple-
mentary indications to those specified(E)Space for smoke coefficient (JTD ver-
sions)
(F)Space for punching manufacturer’s
name.
BODYWORK LABEL
This is located in the engine bay, to one side
of the upper right shock absorber (fig. 3)
and contains:
– Type of vehicle: ZAR 937.000
– Manufacturer’s serial number (chassis
number).
IDENTIFICATION DATA
You are advised to note the identification
codes. The identification datastamped and
given on the labels and their position are
the following (fig. 1):
1- Identification label
2- Body label
3- Bodywork paint identification label
4- Engine label.
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
fig. 1
A0A0654b
fig. 2
A0A0246b
fig. 3
A0A0247b

TECHNICAL SPECIFICATIONS
272
BODYWORK PAINT
IDENTIFICATION LABEL
The label (fig. 4) is on the inner left edge
of the tailgate. It contains the following in-
formation:
A. Paint manufacturer.
B. Name of colour.
C. Colour code.
D.Indication on the type of product to be
used for touching-up.
ENGINE STAMP
The engine marking is stamped on the
gearbox side of the crankcase, in corre-
spondence with the exhaust manifold.
ENGINE CODES - BODY VERSIONS
fig. 4
A0A0651b
Engine code Body versions
1.8 T. SPARKAR322005 937CXR1A 26
2.0 JTS937A1000 937CXH1A 22
2.0 JTS
932A2000 937CXHT1A 29
(For specific markets)
2.0 JTS Selespeed937A1000 937CXH11 23
3.2V6936A000 937CXP1B 25
JTD16V937A5000 937CXN1B 24B

TECHNICAL SPECIFICATIONS
273
ENGINE
2.0 JTS
2.0 JTS
Selespeed
937A1000
Otto
4 in line
83 x 91
1970
11.5 : 1
121
165
6400
206
21
3250
NGK PFR6B
NGK BKR6EKPA
Unleaded
premium petrol
95 RON2.0 JTS (**)
932A2000
Otto
4 in line
83 x 91
1970
11.5 : 1
119
163
6400
201
22
3250
NGK PFR6B
NGK BKR6EKPA
Unleaded
premium petrol
95 RONJTD16V
937A5000
Diesel
4 in line
82 x 90.4
1910
17.5 : 1
110
150
4000
305
31
2000
Diesel for motor
vehicles
(Specification
EN 590) 3.2
V6
936A000
Otto
6 at V of 60°
93 x 78
3179
10 : 1
176.5
240
6200
300
30,6
4800
NGK PFR6B
Unleaded
premium petrol
95 RON
(*) There are two different spark plugs for each cylinder, one per type
(**) For versions/markets where applicable.1.8 T. SPARK
AR32205
Otto
4 in line
82.7
1747
11.5 : 1
103
140
6500
163
16.6
3900
NGK PFR6B+
NGK PMR7A
NGK BKR6EKPA+
NGK PMR7A
Unleaded
premium petrol
95 RONCode type
Cycle
Number and position of cylinders
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum horsepower (EEC):
kW
HP
at rpm
Maximum torque (EEC):
Nm
kgm
at rpm
Spark plugs (*)
Fuel

TECHNICAL SPECIFICATIONS
274
FUEL SUPPLY
Alterations or repairs to the fuel supply system carried out incorrectly and without taking account of
the technical features of the system, may cause operating faults with the risk of fire.
TRANSMISSION
Supply
2.0 JTS
Direct electronic injection
Gearbox
Clutch
Drive
2.0 JTS
Five forward gears plus
reverse with
synchronisers for forward
speeds
Dry single disk with
hydraulic control
Front
JTD16V
Six forward gears plus
reverse
all synchronised
Dry single disk with
hydraulic control
Front
JTD16V
Common Rail direct injection
with supercharging
3.2V6
Multi Point electronic injection
3.2V6
Six forward gears plus
reverse all synchronised
Dry single disk with
hydraulic control
Front
2.0 JTS Selespeed
Five forward gears and
reverse with electronic
control
Dry single disk with
electrohydraulic control
Front
1.8 T. SPARK
Multi Point electronic
injection
1.8 T. SPARK
Five forward gears plus
reverse with
synchronisers for
forward speeds
Dry single disk with
hydraulic control
Front

TECHNICAL SPECIFICATIONS
275
Service brakes:– front
– rear
Parking brake
BRAKES
Front
Rear
Type
Turning radius
(between pavements) m1.8 T. SPARK - 2.0 JTS - 3.2
V6 - JTD16V
rack and pinion with hydraulic power steering
11.5
SUSPENSIONS
STEERING SYSTEM
1.8 T. SPARK - 2.0 JTS - 3.2 V6- JTD16V
Disk
Disk
Controlled by hand lever, acting on the rear brakes
1.8 T. SPARK - 2.0 JTS - 3.2
V6 - JTD16V
quadrilateral system with stabiliser bar
Mc Pherson type

TECHNICAL SPECIFICATIONS
276
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims.
Radial tubeless tyres.
The log book shows all the homologated
tyres.
IMPORTANTIn the event of any dis-
crepancies between this Handbook and the
vehicle Log Book, only the latter should be
considered.
While the specified dimensions remain the
same, for driving safety, the vehicle must be
fitted with tyres of the same brand and type
on all wheels.
IMPORTANTDo not use inner tubes
with Tubeless tyres.
COMPACT SPARE WHEEL
Pressed steel rim.
WHEEL GEOMETRY
Convergence of front wheels measured be-
tween the rims:
The values refer to the vehicle travelling.
CORRECT TYRE READING
Below, please find the instructions need-
ed to understand the meaning of the code
stamped on the tyre. Example:
205/55 R 16 91 W
or
205/55 ZR 16
The code may be in one of the ways giv-
en in the example.
205= Nominal width (distance in
mm between sides).
55= Percentage height/width
ratio.
R= Radial tyre.
ZR= Radial tyre, with speed over
240 km/h.
16= Rim diameter in inches.
91= Load index (capacity), e.g. 91
= 615 kg. Not present in ZR
tyres.
W,Z= Maximum speed index. In ZR
tyres the speed index Z is be-
fore the R.
fig. 5
A0A0465b

TECHNICAL SPECIFICATIONS
277
Load index (capacity)
60= 250 kg
61= 257 kg
62= 265 kg
63= 272 kg
64= 280 kg
65= 290 kg
66= 300 kg
67= 307 kg
68= 315 kg
69= 325 kg
70= 335 kg
71= 345 kg
72= 355 kg
73= 365 kg
74= 375 kg
75= 387 kg
76= 400 kg
77= 412 kg
78= 425 kg
79= 437 kg
80= 450 kg
81= 462 kg
82= 475 kg
83= 487 kg
84= 500 kg85= 515 kg
86= 530 kg
87= 545 kg
88= 560 kg
89= 580 kg
90= 600 kg
91= 615 kg
92= 630 kg
93= 650 kg
94= 670 kg
95= 690 kg
96= 710 kg
97= 730 kg
98= 750 kg
99= 775 kg
100= 800 kg
101= 825 kg
102= 850 kg
103= 875 kg
104= 900 kg
105= 925 kg
106= 950 kgMaximum speed index
for snow tyres
Q M +S= up to 160 km/h.
T M +S= up to 190 km/h.
H M +S= up to 210 km/h. Maximum speed index
Q= up to 160 km/h.
R= up to 170 km/h
S= up to 180 km/h.
T= up to 190 km/h.
U= up to 200 km/h.
H= up to 210 km/h.
V= over 210 km/h.
ZR= over 240 km/h.
W= up to 270 km/h.
Y= up to 300 km/h.

Standard fittings
Rims
Tyres
Fittings on request
Rims
Tyres
Winter tyres
2.0 JTS
7 J x 16
7 J x 17 ()
71/2J x 17 ()
205/55 R16 91W
(•)205/55 ZR16 (•)215/45 R17 87W ()
61/2J x 15
7 J x 17
8 J x 18
195/60 R15 88V (**)
215/45 R17 87W
(•)215/45 ZR17 87W
(Pirelli P7000) (•) (*)215/45 ZR17 87Y
(Good Year Eagle F1) (•) (*)
225/40 ZR18 92Y
(Michelin Pilot Sport 2) (
•) (*)
195/60 R15 88Q (M+S)
205/55 R16 91T (M+S)
215/45 R17 87H (M+S)
3.2V6
71/2J x 17
225/45 ZR17 91Y
(Pirelli Pzero Rosso) (
•) (*)225/45 ZR17
(Bridgestone S-02) (•) (*)
71/2J x 17
8 J x 18
215/45 R17 87W (**)
215/45 R17 87W
(Pirelli P7000) (*) (**)
215/45 ZR17 87Y
(Good Year Eagle F1) (*) (**)
225/40 ZR18 92Y
(Michelin Pilot Sport 2) (
•) (*)
215/45 R17 87H (M+S)
225/45 ZR17 91H (M+S)
(•) Unchainable tyres
() For versions/markets where applicable
(*) Size certified and admitted for specified tyres only
(**)IMPORTANTChainable tyres; see paragraph "Snow chains" in section "Correct use of the car".
JTD16V
61/2J x 15
7 J x 16
7 J x 17 (
)
71/2J x 17 ()
205/60 R15 91V
(•)205/55 R16 91W (•)205/55 ZR16 (•)215/45 R17 87W ()
61/2J x 15
7 J x 17
8 J x 18
195/60 R15 88V (**)
215/45 R17 87W
(•)215/45 ZR17 87W
(Pirelli P7000) (•) (*)
215/45 ZR17 87Y
(Good Year Eagle F1) (
•) (*)
225/40 ZR18 92Y
(Michelin Pilot Sport 2) (
•) (*)205/60 R15 91V(Michelin Pilot Primacy) (•) (*)
195/60 R15 88Q (M+S)
205/55 R16 91T (M+S)
215/45 R17 87H (M+S)
TECHNICAL SPECIFICATIONS
278
1.8 T SPARK
61/2J x 15
7 J x 16
7 J x 17 (
)
71/2J x 17 ()
205/60 R15 91V
(•)205/55 R16 91V (•)205/55 ZR16 (•)215/45 R17 87W ()
61/2J x 15
7 J x 17
8 J x 18
195/60 R15 88V (**)
215/45 R17 87W
(•)215/45 ZR17 87W
(Pirelli P7000) (•) (*)215/45 ZR17 87Y
(Good Year Eagle F1) (•) (*)
225/40 ZR18 92Y
(Michelin Pilot Sport 2) (
•) (*)205/60 R15 91V(Michelin Pilot Primacy) (•) (*)
195/60 R15 88Q (M+S)
205/55 R16 91T (M+S)
215/45 R17 87H (M+S)