Alfa Romeo GT 2006 Owner handbook (in English)

IN AN EMERGENCY
229
– Replace the bulb;
– Refit the bulb holder turning counter-
clockwise and check that it is secured cor-
rectly;
– Refit the transparent.SIDE DIRECTION INDICATORS
(fig. 30)
– Push the transparent cover towards
the rear of the car to compress the catch
(A). Release the front part and remove
this unit.
– Turn the bulb holder (B) counter-clock-
wise and remove it from the cover.
– Remove the snap-fitted bulb and
replace it.
– Insert the bulb holder (B) in the trans-
parent cover, then position the unit mak-
ing sure the catch clicks into place (A).
fig. 29
A0A0626b
fig. 30
A0A0166b
FRONT DIRECTION
INDICATORS
(fig. 28-29)
To change the bulb, proceed as follows:
– Using the screwdriver provided,
remove the transparent unit operating on
the two metal clips as shown in the figure;
– Turn the bulb holder clockwise (A)
and remove it;
– Remove the bulb (B) pushing gently
and turning counter-clockwise;
fig. 28
A0A0625b

IN AN EMERGENCY
230
REVERSING LIGHT
AND REAR FOG GUARDS
(fig. 31-32)
The reversing light and rear fog guard are
in the tail light unit fastened to the tailgate;
they are to be found respectively one on the
right and the other on the left of the vehicle
facing forwards.
To change the bulb, proceed as follows:
– from the bumper lower side (fig. 31),
operate on the bulb holder (A-fig 32) turn-
ing it counter-clockwise and remove it. Take
care not to get burnt if the muffler is still hot;
fig. 31
A0A0627b
fig. 33
A0A0629b
– Remove the bulb pushing gently and
turning counter-clockwise;
– Replace the bulb, then refit the bulb
holder.
Anyway, you are advised to have this
operation carried out by Alfa Romeo
Authorised Services.REAR DIRECTION INDICATORS
AND REAR SIDELIGHTS-
BRAKING LIGHTS
(fig. 33-34)
The rear direction indicators and the side-
lights-braking lights are in the tail light
unit fastened to the body.
To change the bulb, proceed as follows:
– From inside the boot, open the com-
partment (A-fig. 33) and then the door
(B) through the tab (C);
– Turn the bulb for sidelight and braking
light counter-clockwise (D-fig. 34),
or the bulb for the direction indicator (E-
fig. 34) and remove it;
fig. 32
A0A0628b

IN AN EMERGENCY
231
NUMBER PLATE LIGHTS
(fig. 35)
To change the bulbs, proceed as follows:
– Work on the transparent cover frame,
in the point shown by the arrow to com-
press the catch (B). Free the opposite end
and remove the unit.
– Turn the bulb holder counter-clockwise
(A) and remove it from the transparent
cover.
– Remove the snap-fitted bulb and
replace it.
– Insert the bulb holder (A) in the trans-
parent cover then refit the unit checking
that the catch clicks into place (B).
ADDITIONAL BRAKING LIGHT
(THIRD STOP)
(fig. 36-37)
To change the led unit, proceed as fol-
lows:
– Open the tailgate and use a screwdriv-
er to open the two covers (A-fig. 36);
– Slacken the two fastening screws of
(B) the led unit;
fig. 35
A0A0171b
fig. 36
A0A0631b
A0A0630b
– Withdraw the light (ForG) push it
gently and turn counter-clockwise;
– Replace the bulb;
– Refit the bulb holder turning clockwise
and make sure it is secured correctly;
– Refit the door (B) and close the com-
partment (A).
fig. 34

IN AN EMERGENCY
232
– disconnect the connector (C-fig. 37),
remove the led unit (D) and replace it with
a new unit;
– Refit the unit on the tailgate reversing
the above mentioned procedure.
fig. 37
A0A0632b
fig. 39
A0A0175b
PUDDLE LIGHTS (fig. 38)
(per versions/market where
provided)
To change the bulb, proceed as follows:
– Open the door and slacken the screw
(A) fastening the transparent covers.
– Remove the unit composed of the two
transparent covers then change the bulb,
releasing it from the side contacts making
sure that the new bulb is correctly
clamped between the contacts.
– Realign the two transparent covers
and tighten the fastening screw (A).
IF AN INTERIOR
LIGHT GOES OUT
FRONT ROOF LIGHT
(fig. 39-40)
To change the bulbs, proceed as follows:
– Remove the light unit (A) levering in
the points shown by the arrow (in corre-
spondence with the retainer catches).
– Open the protective cover (B).
– Replace the bulb concerned releasing
it from the side contacts making sure that
the new bulb is correctly clamped
between the contacts.
fig. 38
A0A0174b

IN AN EMERGENCY
233
REAR ROOF LIGHT
(fig. 41-42)
To change the bulb, proceed as follows:
– Remove the light unit (A) levering in
the point shown by the arrow.
– Replace the bulb releasing it from the
side contacts making sure that the new
bulb is correctly clamped between the con-
tacts.– Refit the light unit in the correct posi-
tion inserting first the side with the con-
nector, then pressing the other side until
the catch clicks into place (B).
fig. 41
A0A0177b
fig. 42
A0A0178b
– Close the protective cover (B).
– Refit the light unit pressing gently in
correspondence with the retainer catches,
until hearing the click.
fig. 40
A0A0176b

IN AN EMERGENCY
234
COURTESY MIRROR
LIGHT
(fig. 43-44)
To change the bulb, proceed as follows:
– Open the mirror cover (A).
– Remove the transparent cover (B) lev-
ering in the point shown by the arrow.
– Gently raise the bulb holder (C) from
its housing, remove the snap-fitted bulb
and change it.– Put the bulb holder correctly (C) back
in its housing.
– Refit the transparent cover (B) insert-
ing it in its correct position firstly on one
end and then on the other until it clicks
into place.
fig. 43
A0A0179b
fig. 44
A0A0180b
GLOVEBOX LIGHT (fig. 45-46)
To change the bulb, proceed as follows:
– Open the glovebox, then remove the
light unit (A) levering in the point shown
by the arrow.
– Open the protection (B) and change
the snap-fitted bulb.
– Close the protection (B) on the trans-
parent cover.
fig. 45
A0A0181b

IN AN EMERGENCY
235
BOOT LIGHT (fig. 47-48)
To change the bulb, proceed as follows:
– Open the tailgate;
– Remove the light unit (A-fig. 47)
levering in the point shown by the arrow; – Refit the light unit inserting it in its cor-
rect position firstly on one end and then
on the other until it clicks into place.– Replace the bulb (B-fig. 48) releas-
ing it from the side contacts, making sure
that the new bulb is correctly clamped
between the contacts;
– Refit the light unit inserting it in its cor-
rect position firstly on one end and then
on the other until it clicks into place (C).
fig. 46
A0A0182b
fig. 47
A0A0648b
fig. 48
A0A0649b

IN AN EMERGENCY
236
IN THE EVENT OF A BLOWN FUSE
GENERAL
The fuse is a protective device for the
electric system: it comes into action (i.e. it
cuts off) mainly due to a fault or improp-
er action on the system.
When a device does not work, check the
efficiency of its fuse. The conductor ele-
ment(A-fig. 49) must be intact; if not,
replace the fuse with one of the same
amp rating (same colour).(B) - Undamaged fuse
(C) - Fuse with damaged filament.
Remove the blown fuse using the pincer
provided (D), in the control box.
fig. 49
A0A0185b
Never replace a fuse
with metal wires or any-
thing else. Always use an
intact fuse of the same colour.
Never replace a fuse
with another with a high-
er amp rating; DANGER
OF FIRE.
If a general fuse (MAXI-
FUSE or MEGA-FUSE) cuts
in, do not attempt any
repair and contact Alfa Romeo
Authorised Services.
Before replacing a fuse,
make sure the ignition
key has been removed
and that all the other services are
switched off and/or disengaged.
If a fuse blows again,
contact an Alfa Romeo
Authorised Service.

IN AN EMERGENCY
237
To locate the protection fuses, consulting
the summary table on the following
pages, refer to the following illustrations
fig. 52,fig. 53and54.Alfa GTfuses are located in three
fuse boxes set on the dashboard, on bat-
tery positive terminal and near the bat-
tery.
Access is gained to the control box on
the dashboard by slackening the two
retainers (A-fig. 50) and removing the
protective trim (B).
To gain access to the fuses in the fuse-
box on the battery post, remove the pro-
tective cover pressing the opening catches
(front).
Access is gained to the control box next
to the battery releasing the perimetral
catches (A-fig. 51) and removing the
protective cover (B).
fig. 50
A0A0186b
fig. 51
A0A0187b
fig. 52 - Control box on dashboard
A0A0134b

IN AN EMERGENCY
238
fig. 53 - Control box next to battery
A0A0137b
fig. 54 - Control box on battery positive pole
A0A0215b