service Alfa Romeo GT 2006 Owner handbook (in English)

1
Dear Client,
Thank you for choosing Alfa Romeo.
Your Alfa GThas been designed to guarantee the safety, comfort and driving pleasure typical of Alfa Romeo.
This booklet will help you to get to know the characteristics and operation of your vehicle.
The following pages contain all the indications necessary for you to be able to maintain the high standards of performance, quality, safety
and respect for the environment which characterise this Alfa GT.
The Warranty Booklet also contains the regulations, the warranty certificate and a guide to the services offered by Alfa Romeo.
Services which are essential and precious because, when you purchase an Alfa Romeo, you are not only acquiring a car, but the tranquillity
that comes from knowing that an efficient, willing and widespread organisation is at your service for any assistance problems you may have.
We would like to point out Alfa Romeo’ s commitment in protecting the environment through "total material recycling": at the end of your
Alfa GTuseful lifespan, any Alfa Romeo dealer would be pleased to make arrangements for your car to be recycled properly and eco-
logically (in compliance with current law regulations).
Nature benefits in two ways: there’s no pollution from waste disposal and the demand for raw materials is reduced.
Enjoy the reading. And have a good trip.
This booklet describes all the versions of the Alfa GT, so you should only consider the information concerning
the trim level, engine and version purchased by you.

3
ACCESSORY ELECTRICAL DEVICES
If after purchasing the car you wish to install accessories that need an electrical supply (with the risk of gradually draining
the battery), contact Alfa Romeo Authorised Services who will assess the overall electrical absorption and check whether the
car system is able to withstand the load required.

CODE CARD
Keep it in a safe place, not in the car. IT is advisable to always keep the electronic code on the CODE card with you in case
emergency starting is necessary.
SCHEDULED SERVICING
Correct maintenance makes it possible to preserve vehicle performance levels and safety, respect for the environment and
low running costs unaltered over the course of time.
THE OWNER HANDBOOK…
…you will find important information, advice and warnings for correct use, driving safety and vehicle maintenance over
time. Pay particular attention to the symbols
"(personal safety) #(protecting the environment) â(vehicle safety).
RESPECTING THE ENVIRONMENT
The vehicle is fitted with a system that allows continuous diagnosis of the components correlated with emissions to ensure
better respect for the environment.
U

4
Any queries concerning servicing should be forwarded to the showroom from which the vehicle was purchased, the subsidiary company or to
our branch offices or any point of the Alfa Romeo Network.
Warranty Booklet
The Warranty Booklet is delivered together with every new vehicle and contains the regulations tied to the service given by Alfa Romeo and
to the warranty conditions.
Correctly carrying out the scheduled services specified by the manufacturer is the best way to maintain the performance, safety characteris-
tics and low running costs of your vehicle. It is also necessary to maintain warranty cover.
“Service” guide
This contains Alfa Romeo Authorised Services. The Services can be recognised by the presence of the Alfa Romeo badge and logo.
The Alfa Romeo organisation in Italy can be found in the telephone directory under the letter “A” Alfa Romeo.
Not all of the models described in this booklet are available in all countries. Only some of the fittings described in this booklet are fitted as
standard to the vehicle. The list of available accessories should be requested from the Alfa Romeo Dealers.

The codes of any keys not
presented during the mem-
orising procedure are
erased. The reason for this is to en-
sure that any lost or stolen keys
cannot be used to start the engine.
GETTING TO KNOW YOUR CAR
9
OPERATION
Each time the ignition key is turned to the
STOPposition the Alfa Romeo CODE sys-
tem deactivates the functions of the engine
electronic control unit.
Each time the car is started turning the
ignition key to MAR, the Alfa Romeo
CODE control unit sends a recognition
code to the engine control unit to deacti-
vate the inhibitor. The code is crypted and
variable between over four billion possible
combinations, and it is sent only if the sys-
tem control unit has recognised the code
transmitted from the key which contains
an electronic transmitter, through an aeri-
al wound around the ignition switch.IMPORTANTTurning on of the Alfa
Romeo CODE warning light (
Y) when
travelling with the ignition key at MAR:
1) If the warning light turns on, this
means that the system is running a self-
test (for example for a voltage drop). At
the first stop, it will be possible to test the
system: switch off the engine turning the
ignition key to STOP; then turn the igni-
tion key to MAR: the warning light turns
on and should go off in about one second.
If the warning light stays on, repeat the
procedure described previously leaving the
key at STOPfor over 30 seconds. Should
the inconvenience persists, contact Alfa
Romeo Authorised Services. If the code has not been recognised cor-
rectly, the Alfa Romeo CODE warning light
(
Y) on the cluster turns on.
In this case, the key should be moved to
theSTOPposition and then back to
MAR; if the lock continues, possibly try
again with the other key provided with the
car. If it is still not possible to start the car,
follow the instructions given in the “In an
emergency” chapter and then contact Alfa
Romeo Authorised Services.
IMPORTANTEvery key has its own
code, which must be memorised by the
system control unit. To memorise new
keys, up to a maximum of eight, apply
solely to Alfa Romeo Authorised Services
taking with you all the keys in your pos-
session, the CODE card, a personal identi-
ty document and the car’s ownership doc-
uments.

GETTING TO KNOW YOUR CAR
10
2) For versions without the reconfig-
urable multifunction display, the flashing
of the warning light means that the car is
not protected by the engine inhibitor
device. This condition for cars with recon-
figurable multifunction display is shown by
the turning on of the warning light togeth-
er with the display of the message: “C
ODE
SYSTEM NOT PROGRAMMED
”. Contact Alfa
Romeo Authorised Services immediately
to have all the keys memorised.
If after about 2 seconds
with the ignition key at
MAR, for versions without
reconfigurable multifunction dis-
play, the Alfa Romeo CODE warn-
ing light (
Y) turns on again flash-
ing, or for versions with reconfig-
urable multifunction display, the
warning light turns on again to-
gether with the message “Code
system not programmed”, this
means that the code of the keys
has not been stored, therefore the
car is not protected by the Alfa
Romeo CODE system against at-
tempted theft. In this case contact
Alfa Romeo Authorised Services to
have the key codes stored.
KEY BATTERY REPLACEMENT
If when pressing button (BorC-fig. 6)
on the remote control, nothing happens,
the battery should be replaced by a new
one of the same type to be found c/o nor-
mal retailers.
Used batteries are harm-
ful to the environment.
They should be disposed of
as specified by law in the special
containers provided. Avoid expo-
sure to naked flames and high tem-
peratures. Keep out of reach of
children.
fig. 5
A0A0603b
Battery replacement:
– press button (A-fig. 5) and move
the metal insert (B) to the open position;
– using a finely-tipped screwdriver, turn
the opening device (C) and pull out the
battery holder (D);
– replace the battery (E) making sure
that the bias is correct;
– re-insert the battery holder in the key
and lock it, turning the device (C).

GETTING TO KNOW YOUR CAR
11
ELECTRONIC ALARM
DESCRIPTION
The system comprises: a transmitter,
receiver, control unit with siren and volu-
metric sensors. The electronic alarm is
controlled by the receiver incorporated in
the instrument cluster and it is turned on
and off by the remote control in the key
which sends the crypted and variable
code. The electronic alarm controls: the
unlawful opening of doors, bonnet and
boot (perimetral protection), operation of
the ignition key, battery cable cutting, the
presence of moving bodies in the passen-
ger compartment (volumetric protection),
any abnormal raising/sloping of the car
(for versions/markets where applicable)
and central door locking. It also makes it
possible to cut off the volumetric protec-
tion.
IMPORTANTThe engine inhibitor
function is guaranteed by the Alfa Romeo
CODE system which is activated automati-
cally when the ignition key is removed.The remote control is incorporated in the
key with buttons (B, C, D-fig. 6) which
activate the corresponding control and
send the code to the receiver. This code
(rolling code) changes at each transmis-
sion.
REQUEST FOR ADDITIONAL
KEYS WITH REMOTE CONTROL
The receiver can recognise up to 5 keys
with incorporated remote control. Should
a new key with remote control be neces-
sary for any reason during the life of the
car, contact directly Alfa Romeo Authorised
Services, taking with you the CODE card,
a personal identity document and the car’s
ownership documents.
HOW TO ACTIVATE THE
ALARM
With the doors, bonnet and boot shut
and the ignition key in the STOPor
PARKposition (key removed), point the
key with the remote control in the direction
of the car, then press and release the but-
ton (C-fig. 6).
With the exception of certain markets,
the system sounds a “beep” and the
doors are locked.
Engagement of the alarm is preceded by
a self-diagnostic test indicated by a differ-
ent flashing frequency of the deterrent led
(A-fig. 7) on the dashboard. If a fault is
detected the system sounds a further
warning “beep”.
fig. 6
A0A0601b
fig. 7
A0A0005b

GETTING TO KNOW YOUR CAR
12
– if the led continues flashing, but at dif-
ferent intervals than normal, this means
that different attempts to break in have
occurred. Through the number of flashes it
is possible to identify the type of attempt:
1 flash:one or more doors
2 flashes:tailgate
3 flashes:bonnet
4 flashes:ultrasounds
5 flashes:abnormal vehicle lift-
ing/sloping (for ver-
sions/markets where
applicable)
6 flashes:tampering with car start-
ing cables
7 flashes:tampering with battery
cables or cutting emer-
gency key cables
8 flashes:connection line to sen-
sors and siren
9 flashes:at least three causes of
alarm. Surveillance
After switching on, the flashing of the
deterrent led (A-fig. 7) on the dash-
board indicates the system surveillance
mode. The led flashes throughout this
period.
IMPORTANTOperation of the elec-
tronic alarm is adapted at the origin to the
rules of the different countries.
Self-diagnostic functions
and door, bonnet, boot control
If, after engaging the alarm, a second
“beep” is sounded, switch off the system
pressing the button (B-fig. 6), check
that the doors, bonnet and tailgate are
properly shut, then switch the system on
again pressing the button (C). Otherwise,
the door, bonnet or tailgate that is not
shut properly will be excluded from the
alarm system control.
If the doors, bonnet and boot are shut
correctly and the control signal is repeat-
ed, the system self-diagnostic has detect-
ed a system operating fault. It is therefore
necessary to contact Alfa Romeo
Authorised Services.HOW TO DEACTIVATE
THE ALARM
To deactivate the alarm press the button
(B-fig. 6) of the key with remote control.
The system will react as follows (with the
exception of certain markets):
– two brief flashes of the direction indi-
cators
– two brief “beeps” of the system
– door unlocking.
IMPORTANTIf when the system is
turned off the deterrent led (A-fig. 7)
on the dashboard stays on (maximum 2
minutes or until the ignition key is set to
MAR) the following should be borne in
mind:

GETTING TO KNOW YOUR CAR
14
IGNITION DEVICE
SWITCH(fig. 8)
The key can be turned to one of four
positions:
–STOP: engine switched off, key can
be removed, engine inhibitor engaged,
steering lock engaged, services excluded
apart from those supplied directly (e.g.
hazard warning lights).
–MAR: drive position. The engine lock
is deactivated and all electrical devices are
powered.
fig. 8
A0A0016b
When leaving the vehicle
always remove the key
from the ignition to pre-
vent any occupants of the vehicle
from accidentally activating the
controls. Never leave children in
the vehicle unaccompanied. Re-
member to engage the handbrake
and, if the vehicle is parked on an
uphill slope, to engage the first
gear. If the vehicle is facing down-
hill, engage reverse gear.
If the ignition device is
tampered with (for exam-
ple an attempted theft)
have it checked over by Alfa
Romeo Authorised Services before
travelling again.
IMPORTANTDo not leave the key in
this position when the engine is stopped.
–AV V: unstable position for starting
the engine.
IMPORTANTIf the engine fails to
start move the key back to STOPand
repeat.
The ignition switch has a safety device
which prevents passage to AV Vwhen
the engine is running.
–PARK: engine switched off, key can
be removed, engine lock engaged, steer-
ing lock engaged, sidelights switched on
automatically.
IMPORTANTTo turn the key to the
PARKposition, button (A) on the switch
must be pressed first.

GETTING TO KNOW YOUR CAR
24
POWER WINDOWS
For some versions, the power windows
are fitted with a safety system with crush-
prevention seals. The electronic control
unit that operates the system is capable of
detecting the presence of an obstacle dur-
ing the window closing motion through
the special seals. Should this occur, the
system stops the movement of the win-
dow and reverses it immediately.IMPORTANTIf the crush-prevention
function is operated for 3 times in 1
minute, the system automatically sets to
the “recovery” mode (self-protection). To
reset the correct system operating logic,
press the control button until full window
opening. The logic is reset and if there are
no faults, the window winder automatical-
ly resumes normal operation; if not con-
tact Alfa Romeo Authorised Services.
IMPORTANTWith the ignition key at
STOPor removed, the power windows
remain activated for about 3 minutes and
are deactivated immediately the moment
a door is opened.
Driver’s side (fig. 33)
The driver’s door panel contains the but-
tons that control the following windows,
with the ignition key at MAR:
A- left front window
B- right front window.
Press the button to lower the window.
Pull to raise it. Defrosting/demisting
(fig. 31-32)
The electric mirrors are fitted with heat-
ing coils which come into operation with
rearscreen heating pressing the button
(A) thereby defrosting and/or demisting
the mirrors.
IMPORTANTThe function is timed
and automatically switched off after a few
minutes.
fig. 32
A0A0612b
fig. 31
A0A0042b

GETTING TO KNOW YOUR CAR
29
Pre-tensioning devices
can only be used once. Af-
ter they have been trig-
gered contact Alfa Romeo Autho-
rised Services to have them re-
placed. The validity of the device is
10 years from the date of produc-
tion on the sticker; the pretension-
ers should be changed at an Alfa
Romeo Authorised Service as this
date approaches.
Operations involving
banging, vibrations or
heating (above 100°C for
a maximum of 6 hours) in the area
of the pretensioners may damage
or trigger off the device. Vibrations
from rough road surfaces or acci-
dental jolting caused by mounting
pavements etc. do not have any ef-
fect on the pretensioner. If, how-
ever, you need assistance, go to Al-
fa Romeo Authorised Services.
fig. 40
A0A0675b
LOAD LIMITERS
To increase passengers’ protection in the
event of an accident, the front and rear
(where provided) seat belt reels contain a
load limiter which allows controlled sag in
such a way as to dose the force acting on
the shoulders and chest during the belt
restraining action in case of a crash.
GENERAL INSTRUCTIONS
FOR THE USE OF THE SEAT
BELTS
All the occupants of the car are obliged
to respect the local traffic laws regarding
the wearing of seat belts.
Always fasten the seat belts before start-
ing.
Seat belts are also to be worn by expec-
tant mothers: the risk of injury in the case
of accident is greatly reduced for them
and the unborn child if they are wearing a
seat belt. Pregnant women must of course
position the lower part of the belt very low
down so that it passes under the abdomen
(as illustrated in fig. 40).