stop start Alfa Romeo GT 2007 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
111
SYSTEM ACTIVATION
IMPORTANTOpening the driver’s door,
the Selespeed starts the hydraulic part of
the system to prepare it for the engine to be
started.
Turning the ignition key to MAR, all the
segments of the display (fig. 119), the
gearbox warning light (fig. 120) and the
wordCITYturn on. After about one second,
the display indicates the gear engaged (N,
1,2,3,4,5,R).
IMPORTANTIf after 10 seconds the dis-
play segment do not display the gear en-
gaged or the warning light stays on, turn the
ignition key to STOPand wait for the dis-
play to go off, then repeat the system acti-
vation procedure. If the fault persists, con-
tact Alfa Romeo Authorized Services. With gearshift to CITYgears can be shift-
ed manually using both the gearshift lever
or the steering wheel controls. Gearshift
stays in CITY.
The gear selected (fig. 119) is always
displayed regardless of the mode being se-
lected selected .
N= neutral;
1= first gear;
2= second gear;
3= third gear;
4= fourth gear;
5= fifth gear;
R= reverse. InCITYorSPORT, the selected mode is
also displayed.
IMPORTANT SPORTmode can only
be activated after deactivating the CITY
mode.
A warning light, a message (fig. 120)
and a buzzer draw the attention of the dri-
ver in the event of a fault at Selespeed trans-
mission.
The Selespeed considerably simplifies use
of the car, reducing the fatigue of city dri-
ving or when frequent gearshifting is re-
quired, at the same time offering brilliant
performance.
fig. 120
A0A9081g

GETTING TO KNOW YOUR CAR
112
If the car is on the move, the request is
not accepted; wait for the car to stop and
then request reverse gear engagement
again.
IMPORTANTOnce a gear has been
changed it is necessary to immediately re-
lease the gearshift control lever after mak-
ing the request. A manoeuvre prolonged
(over 10 seconds) makes the system au-
tomatically switch to CITYmode; every-
thing stops releasing the gearshift lever.
IMPORTANTIf wanting to leave the car
parked on a sloping road with a gear en-
gaged to keep it braked, it is necessary to
check that the display shows the new gear
engaged and then wait for 1 to 2 seconds
before releasing the brake pedal to allow
complete clutch engagement.
fig. 123
A0A0700b
OPERATION WITH ENGINE OFF
IMPORTANTBefore using the gearshift
control lever, always check the gear en-
gaged on the display (N,1,2,3,4,5,
R).
With the engine off and the car station-
ary it is possible to engage all the gears.
With the car stationary and with the brake
pedal pressed, requests to shift gears are
both accepted through the control lever on
the central console or through the steering
wheel levers.
To request gearshifting, in addition to keep-
ing the brake pedal pressed:
– to shift upwards (+) (fig. 121) push
the lever “forwards” (if the car is in first gear
it shifts to second, if in second it shifts to
third and so on up to fifth). If the system
is in neutral (N) or reverse (R) moving thelever forwards causes the engagement of
first gear (1).
– to shift downwards (–) (fig. 121)
push the lever backwards (if the car is in
fifth gear it shifts to fourth, if in fourth it
shifts to third and so on down to first gear).
To allow setting the transmission to neu-
tral (N), starting from the condition with
the car stationary and brake pedal pressed,
move the gearshift lever to the right (fig.
122).
From any gear (N,1,2,3,4,5) and
with the car practically at a standstill, it is
possible to request engagement of reverse
gear, pushing the lever to the right and then
backwards (fig. 123).
fig. 121
A0A0698b
fig. 122
A0A0699b

GETTING TO KNOW YOUR CAR
113
Never remove the ignition
key when the car is mov-
ing. In addition to the fact
that the Selespeed system would
not work properly up to stopping
the car, the steering wheel would
lock automatically the first time it
is turned.
STARTING THE ENGINE
The engine can be started with the gear
engaged or in neutral (N), provided that the
brake pedal is pressed down.
IMPORTANTKeep the pedal fully de-
pressed during starting. Since the brake ped-
al becomes hard if it is pressed repeatedly
with the engine off, in this situation it is nec-
essary to increase the pressure on the ped-
al itself to start the engine.
After starting, the gearbox sets to neutral
automatically, the display shows the letter
(N) and the system selects the operating
mode memorised before switching off.
If the engine fails to start
with the gear engaged, the
driver is alerted of the po-
tentially dangerous situation due
to the fact that the gearbox has
automatically set to neutral by the
buzzer and the display.
SWITCHING OFF THE ENGINE
AND SYSTEM DEACTIVATION
Turning the ignition key to STOPthe en-
gine switches off: the gear selected before
turning the engine off remains engaged.
If the engine stops with the gearbox in
neutral (N), the buzzer and the blinking
of (N) draw the attention of the driver so
that the car can be put in safety conditions
engaging the first gear (1) or reverse (R).
In this case, it is necessary to turn the igni-
tion key to MARand with the brake ped-
al pressed, engage first gear (1) or reverse
(R).
NEVER leave the car with
the gears in neutral (N).
It is absolutely necessary
to turn off the engine con-
sequently deactivating the
Selespeed system keeping the brake
pedal pressed: release the pedal
ONLY when the display goes off.

GETTING TO KNOW YOUR CAR
114
The driver is informed of the reverse gear
engaged condition by the intermittent sound
of the buzzer as well as by the display.
IMPORTANTIf while shifting from re-
verse (R)/first gear (1) or neutral (N)/
first gear (1) sticking occurs on the first
gear, the system automatically engages sec-
ond gear (2).
This should not be considered a failure be-
cause it is part of the operating logic. For
the same reason, if sticking occurs on re-
verse gear, the system controls partial clutch
closing so that the gear can be engaged;
in this case the engagement of reverse gear
(R) will not be as smooth as usual. After a request to shift
gear with the car station-
ary, before pressing the ac-
celerator pedal to make the car
start, the driver must always check
that the gear engaged shown on
the display is the one required. MOVING OFF THE CAR
With the engine running and the car sta-
tionary, the gears that can be engaged for
moving off are only first (1), second (2) or
reverse (R).
To engage them it is possible to use the
control lever on the centre console, with the
brake pedal pressed, as the steering wheel
levers allow gear engagement only over 0.5
km/h.
IMPORTANTReverse gear (R) can be
engaged from each of the following other
ratios: neutral (N), first gear (1) or second
gear (2). If the car is on the move, the re-
quest is not accepted; it is necessary to wait
for the car to be completely stopped and
then request reverse (R) again. Moving off the car is obtained:
1) releasing the brake pedal;
2) gradually pressing the accelerator ped-
al.
The more the accelerator pedal is pressed
the higher the car pick-up torque will be.

GETTING TO KNOW YOUR CAR
115
Though strongly inadvisable, if due to un-
foreseen circumstances when driving down-
hill the car is allowed to travel with the gear-
box in neutral (N), when the engagement
of a gear is requested, the system auto-
matically engages the best gear to allow
transmission of the torque to the wheels in
relation to the speed of the car.
When travelling downhill with a gear en-
gaged and the accelerator released (if the
car is moving), beyond a pre-established
speed, the system engages the clutch au-
tomatically to give the car adequate engine
braking.
For safety reasons the Selespeed system
activates the buzzer when: clutch over-
heating occurs during car starting; in this
case, it is necessary to “force” moving off
avoiding hesitations or to release the accel-
erator and use the brake pedal to park the
car if the car is on a slope.Still due to safety reasons, with the car sta-
tionary, the engine running and gear (1),
(2) or (R) engaged, the system activates
the buzzer and automatically shifts to neu-
tral (N) when:
– no action is made on the accelerator
and/or brake pedals for at least 3 minutes;
– the brake is pressed for over 10 min-
utes;
– the driver’s door is opened and the ac-
celerator and brake pedal are not pressed
for at least 1.5 seconds. IMPORTANT NOTES
– With the car stopped and a gear en-
gaged always keep the brake pedal pressed
until deciding to move off;
– during prolonged halts with the engine
running it is advisable to keep the gearbox
in neutral;
– when the car is parked facing uphill, do
not use the moving off manoeuvre to keep
the car still; use the brake pedal and press
the accelerator pedal only when deciding to
move off;
– use second gear only when more con-
trol is needed for moving off manoeuvres at
low speed;
– if, with reverse gear engaged, you need
to engage first gear or vice versa, shift gear
only when the car is completely stationary
and with the brake pedal pressed.

GETTING TO KNOW YOUR CAR
120
PARKING THE CAR
To park the car safely it is absolutely nec-
essary to engage first gear (1) or reverse
(R) and also the handbrake if the road is
on a slope.
Turning the engine off with the car facing
uphill and a gear engaged, it is absolutely
necessary to wait for the gear display to go
off before releasing the brake pedal, so that
the clutch is fully disengaged.
If the gearbox is in neutral (N) and want-
ing to engage a parking gear, the system
should be activated and with the foot on the
brake pedal it is necessary to engage (1)
or (R).
TOWING THE CAR
IMPORTANTFor towing the car, adhere
to local regulations. Make sure that the gear-
box is in neutral (N) (checking that the car
moves when pushed) and proceed as for
towing a normal car with mechanical gear-
box following the instructions given in sec-
tion “In an emergency”.
If setting to neutral is not possible, do not
tow the car and contact Alfa Romeo Autho-
rized Services.
While towing the car do
not start the engine.
BUZZER WARNINGS
The buzzer is activated when:
– reverse gear is engaged (R);
– the car is parked with the gearbox in
neutral (N); signal that can be noted turn-
ing the ignition key to STOP;
– clutch overheating occurs when moving
off;
– the system has shifted automatically
to neutral (N) when:
there is no action on the accelerator
and/or brake pedal for at least 3 minutes;
or the brake is pressed for over 10 min-
utes;
or the driver’s door is opened and no ac-
tion is made on the accelerator and brake
for at least 1.5 seconds;
or detection of a gearbox fault;
– gearbox fault.

GETTING TO KNOW YOUR CAR
121
INTERIOR FITTINGS
GLOVEBOX
On the dashboard there is a glovebox with
lid and light.
To open use handle (A-fig. 128).
When the glovebox is opened with the key
atMARan inside courtesy light turns on
(A-fig. 129).
FRONT ROOF LIGHT
(fig. 130)
The roof light comprises two courtesy lights
with corresponding control switch.
IMPORTANTWhen a door is opened,
the roof light turns on and timing of about
3 minutes is activated automatically, after
which it goes off; closing the doors (within
the 3 minutes) a second timing of about 7
seconds is activated to allow car starting.
fig. 128
A0A0108b
fig. 129
A0A0109b
Never travel with the
glovebox open: the lid
might harm the passenger
in the event of an accident.
The fitting is completed by device (B), on
the lid, for inserting a pen or pencil.
IMPORTANTTurning the ignition key to
STOP, opening the glovebox, the light in-
side can only be turned on for 15 minutes;
after which the system turns it off to avoid
draining the battery.
fig. 130
A0A0111b

GETTING TO KNOW YOUR CAR
123
REAR ROOF LIGHT (fig. 132)
IMPORTANTWhen a door is opened,
the roof light turns on and timing of about
3 minutes is activated automatically, after
which it goes off; closing the doors (within
the 3 minutes) a second timing of about 7
seconds is activated to allow car starting.
Unlocking the doors using the remote con-
trol, the roof light turns on gradually and tim-
ing is activated automatically for about 15
seconds. Locking the doors with the remote
control the roof light turns off gradually.
The light turns off in any case turning the
ignition key to MAR(with the door
closed).PUDDLE LIGHTS (fig. 133)
(for versions/markets where
applicable)
The light (A) housed in the doors turns on
when the associated door is opened, re-
gardless of the position of the ignition key.
fig. 132
A0A0633b
On the light there is a switch with three
positions.
When switch (A) is in the central posi-
tion (0) the light turns on automatically
when a door is opened.
Moving the switch to the right (position 1)
the light stays off.
Moving the switch to the left (position 2)
the light stays on.
IMPORTANTTurning the ignition key to
STOPthe roof light can be turned on for
only 15 minutes; after which it is turned off
to avoid draining the battery.
IMPORTANTBefore leaving the car,
make sure that the switch (A) is in the cen-
tral position (0), so that the roof light turns
off when the doors are closed.
fig. 133
A0A0243b

GETTING TO KNOW YOUR CAR
131fig. 147
A0A0707b
Carry out this operation
only with the car station-
ary.
DANGER-SERIOUS IN-
JURY. When carrying out
checks or maintenance op-
erations in the engine compart-
ment, take special care not to bump
the head on the raised bonnet.
If checks need to be car-
ried out in the engine com-
partment when the engine
is still warm, keep away from the
fan as it could start up even when
the key is removed from the igni-
tion. Wait until the engine cools
down.
BONNET
The bonnet opening lever is under the left
end of the dashboard.
To open:
– pull the lever (A-fig. 146) until the
bonnet clicks open.
– press the safety lever (A-fig. 147)
upwards.
– raise the bonnet.
IMPORTANTBonnet raising is aided by
two gas springs. Do not tamper with these
springs and accompany the bonnet while
raising it.
fig. 146
A0A0135b
Scarves, ties and loose
clothing may be caught in
the moving parts.
For safety reasons the
bonnet must be closed
properly to avoid its open-
ing while the car is travelling.
Therefore, always check it is prop-
erly closed and the catch engaged.
Should you notice that the catch is
not perfectly engaged when trav-
elling, stop the car immediately and
close the bonnet.
To close:
– lower the bonnet until approx. 20 cm
from the engine compartment and then let
it drop, ensuring it is fully closed and not just
held in position by the safety catch.
If the bonnet does not close properly do
not push it down but open it again and re-
peat the above procedure.

GETTING TO KNOW YOUR CAR
135
Always take due care when braking on
bends, even with the help of the ABS.
The most important advice of all, howev-
er, is this:
When the ABS cuts in, and
you feel the pulsing on the
pedal, do not lighten the
pressure, but keep the pedal firm-
ly pressed with no fear; this way
you will stop in the least space
possible, compatibly with the con-
ditions of the road surface.
Following these instructions you will be
in the best braking condition under all cir-
cumstances.
IMPORTANTCars fitted with ABS may
only be fitted with the wheel rims, tyres and
brake linings of type and brand approved by
the Manufacturer.
The system is completed by the EBD (Elec-
tronic Brake Distributor) which distributes
the braking action through the control unit
and the ABS system sensors. The car is fitted with an
electronic braking distribu-
tor (EBD). If the
>andx
warning lights turn on simultane-
ously with the engine running, this
indicates an EBD system failure; in
this case with sharp braking the
rear wheels might lock too early,
with the possibility of skidding. Dri-
ving extremely carefully, go to the
nearest Alfa Romeo Authorised Ser-
vice to have the system checked.
The turning on of only the
>warning light with the
engine running normally in-
dicates a fault to the ABS system
only. In this case the braking sys-
tem is still efficient, though with-
out the aid of the anti-lock device.
Under these conditions perfor-
mance of the EBD system may be
reduced. In this case too, you are
advised to go immediately to the
nearest Alfa Romeo Authorised
Service to have the system checked
over, driving in such a way as to
avoid sharp braking.
If the low brake fluid lev-
el
xwarning light turns
on, stop the car immedi-
ately and contact the nearest Alfa
Romeo Authorised Service. Any
loss of fluid from the hydraulic sys-
tem will negatively affect the op-
eration of the braking system be it
of the conventional type or of the
type with ABS.
If the compact spare
wheel is used, operation of
the ABS system is cut off
and the
>warning light on the in-
strument cluster turns on.
IMPORTANTIf the battery is run down
the
>andxwarning lights might turn on
when starting the engine and go off after
starting. This should not be considered as
a fault but as a warning that during start-
ing the ABS is not active. The turning off
of the warning lights ensures normal system
operation.