window Alfa Romeo GT 2008 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
85
AIR TEMPERATURE
ADJUSTMENT KNOB
Turn the ring of knob (1-fig. 93) clock-
wise or counter-clockwise respectively to
higher or lower the temperature of the air
admitted to the passenger compartment.
FAN SPEED ADJUSTMENT
KNOB
Turning the ring of knob (2-fig. 93) it
is possible to select one of the fan speeds
to personalise the amount of air admitted
to the passenger compartment.
Position0turns off the fan and auto-
matically engages inside air re-circulation
(shown by the lighting up of the led next
to the button 4
v) thereby shutting off
the inlet of outside air to the car.
To switch off inside air re-circulation, press
button (4)
v.
Splitting of air flow between the
windscreen/front side windows
and the lower part of the passenger com-
partment.
Air flow towards the windscreen
and front side windows for demist-
ing/defrosting.
Flow of air to allow quick demist-
ing/defrosting of the windscreen
and front side windows, turning on
rearscreen heating for demisting/defrost-
ing (function called
MAX-DEF).
≤
y
-
AIR DISTRIBUTION KNOB
Turning the knob ring (3-fig. 93), the
following positions are selected in sequence:
Air flow towards the upper centre,
front centre vents and from the
front and rear outlets with the possibility
of adjustment using the controls on the
actual vents.
Splitting of air flow between the pre-
vious vents and the lower part of the
passenger compartment.
Air flow to the lower part of the pas-
senger compartment (front and rear).
μ
w
¥

GETTING TO KNOW YOUR CAR
86
INSIDE AIR RE-CIRCULATION
ON/OFF BUTTON
Pressing button (4-fig. 93)vacti-
vates inside air re-circulation and the led
next to the button lights up.
In this case the climate control system
directly treats the air contained in the pas-
senger compartment, the fan is on.
To switch the air re-circulation feature off
and withdraw air from outside, press the
button again. The inside air recirculation
system makes it possible
to reach the required
“heating” or “cooling” conditions
faster. It is however inadvisable to
use it on rainy/cold days as it
would considerably increase the
possibility of the windows misting
inside, especially if the manual cli-
mate control system is off.
It is advisable to turn on
the inside air recirculation
system
vin queues or
tunnels to avoid admitting pollut-
ed air from outside. The prolonged
use of this function should howev-
er be avoided, especially with sev-
eral persons on board, to avoid the
possibility of the windows misting
inside.
REARSCREEN HEATING
ON/OFFBUTTON
Pressing button (5-fig. 93)(turns
on demisting/defrosting of the rearscreen,
and if present, the door mirrors heating
coils; simultaneously the led next to the but-
ton turns on. This function is timed and
switches off automatically after 20 minutes.
To turn off earlier, press the button again.
IMPORTANTThe system automatical-
ly turns on rearscreen heating if the tem-
perature is below 3°C.
IMPORTANTDo not apply stickers on
the inside of the rearscreen over the heat-
ing filaments to avoid damage which
might cause it to stop working properly.
When cleaning the inside
of the rearscreen, take
care not to damage the
heating filaments.

GETTING TO KNOW YOUR CAR
87
DEMISTING
AND/OR DEFROSTING THE
WINDSCREEN AND FRONT
SIDE WINDOWS, REARSCREEN
AND WING MIRRORS
(MAX-DEF FUNCTION)(fig. 94)
Proceed as follows:
- turn the ring of the air distribution knob
(3) to the
-symbol.
The climate control activates all the func-
tions necessary to quicken demisting/
defrosting of the windscreen and side win-
dows with timing (switching off automati-
cally after 3 minutes), as follows:
- switches off air re-circulation, if engaged;
- sets the maximum air temperature;
- operates the fan at a predefined speed;
- directs the flow of air towards the wind-
screen and front side window vents;
- turns on rearscreen heating and, if pre-
sent, the wing mirror coils. When the max demisting/defrosting func-
tion is on, the led next to the rearscreen
heating button (5)
-will turn on.
IMPORTANTIf the engine is not hot
enough, the function does not immediate-
ly engage the pre-established fan speed,
to restrict the inlet of air to the passenger
compartment that is not warm enough to
demist the windows.
After demisting/defrosting, simply use
the controls to maintain the optimum con-
ditions of vision and comfort.
IMPORTANTThe hotter the engine
the more effective defrosting will be. IMPORTANTIn cases of heavy damp
and/or rain and/or big differences in tem-
perature between inside the car and out-
side, it is advisable to proceed as follows
to demist the windows:
- air re-circulation off, led next to button
(4)
voff;
- pointer of knob (2) at fan second speed
at least;
- pointer of knob (3) on symbol
≤with
the possibility of passing to position
yif
more misting is noted;
To defrost/demist the rearscreen, press
button (5)
(, led next to button on.
A0A0733b
fig. 94

GETTING TO KNOW YOUR CAR
88
HEATING (fig. 95)
To obtain the temperature required, pro-
ceed as follows:
- temperature adjustment knob pointer
(1) on the red sector as required;
- air quantity adjustment knob pointer
(2) on the fan speed required to person-
alise the amount of air admitted;
- air distribution knob pointer (3) on the
required position.
To obtain the maximum heating power
proceed as follows:
- knob pointer (1) as far as it will go clock-
wise (maximum temperature red sector);
- knob pointer (2) on maximum fan
speed;
- air distribution knob pointer (3) on the
required position (position
w) is recom-
mended.
IMPORTANTTo be able to obtain sat-
isfactory passenger compartment warm-
ing, the engine should have reached nor-
mal operating temperature. The filter has the specific capability of fil-
tering external air, thus admitting to the
passenger compartment purified air, free
from particles such as dust, pollen, etc.
In addition to the above mentioned func-
tions, is also reduces the concentration of
pollutants.
The filtering action is active in all air inlet
conditions and it is clearly more effective
with the windows closed.
Have the conditions of the filter checked
at least once a year, preferably at the
onset of summer by Alfa Romeo
Authorised Services. If the car is habitually used in dusty or
polluted areas, the filter should be
checked and replaced at shorter intervals
than those specified in the Programmed
Maintenance Schedule.
If the filter is not replaced
the efficiency of the cli-
mate control system may
be seriously compromised up to
blocking the air flow at the outlets
and vents.
POLLEN FILTER
(for versions/markets where applicable)
A0A0734b
fig. 95

GETTING TO KNOW YOUR CAR
89
AUTOMATIC TWO-ZONE CLIMATE CONTROL SYSTEM
(for versions/markets where applicable)
To start the system (fig. 96):
- turn the knob rings to set the required
temperatures (driver’s side - passenger’s
side).
- press the
AUTObutton.
IMPORTANTThe climate control sys-
tem makes it possible to personalise the
temperatures required on the two side
with a maximum difference of 7°C
between the driver’s side and the passen-
ger’s side.
IMPORTANTThe climate control com-
pressor can only work with the engine run-
ning and external temperature not very
low. With low external tem-
perature the climate con-
trol compressor is unable
to work. It is therefore inadvisable
to use the inside air recirculation
function vwith low outside tem-
perature as windows may mist
over quickly.
For further details about the system and
how to make the best use of it, read the
instructions given in pages that follow.
A0A0203b
fig. 96
The coolant used for the
climate control system is
R134a which meets cur-
rent regulations and does not harm
the environment in the event of ac-
cidental spillage.
Absolutely avoid the use of oth-
er fluids which are incompatible
with the system components.

GETTING TO KNOW YOUR CAR
92
CONTROLS(fig. 97)
1- Inside temperature set display (dri-
ver’s side)
2- Inside temperature adjustment knob
(driver’s side)
3- Fan speed set and system off display
(
OFF)
4- Knob for adjusting the fan speed and
switching the system off
5- Inside temperature set display (pas-
senger’s side)
6- Inside temperature adjustment knob
(passenger’s side)
7- Maximum defrosting/demisting
on/off button for windscreen and front
side windows, rearscreen heating and
wing mirror coils (
MAX-DEFfunction)
8- Inside air re-circulation on/off button
v(manual/automatic)
9- Rearscreen heating and wing mirror
defrosting on/off button
(
10- Air distribution selection buttons 11- Inside air temperature sensor
12- Button for aligning the temperature
set on the passenger’s side with that on
the driver’s side
MONO
13- Button for selecting the system
automatic mode
AUTO
14- Climate control compressor on/off
enable button
√
fig. 97
A0A0090b

GETTING TO KNOW YOUR CAR
99
AIR DISTRIBUTION SELECTION
BUTTONS
(fig. 104)
Pressing one or more buttons (10) it is
possible to manually choose one of the 5
possible air distributions to the passenger
compartment:
REFlow of air to the dashboard centre
and side outlets and rear outlet.
R
ZESplitting of the air flow between the
vents to the lower part of the pas-
senger compartment (warmest air)
and the dashboard centre and side
outlets and the rear outlet (coolest
air). The air flow distribution is par-
ticularly useful in spring and autumn,
when the sun is shining.
ZAir flow towards the front and rear
lower parts of the passenger com-
partment. Due to the natural ten-
dency of heat to spread upwards, this
type of distribution allows heating of
the passenger compartment in the
shortest time, also giving a prompt
feeling of warmth to the coldest parts
of the body.
A0A0208b
Q
ZSplitting of the air flow between the
windscreen and side window defrost-
ing/demisting vents and the lower
part the of the car. This type of air dis-
tribution allows satisfactory heating
of the passenger compartment while
preventing misting of the windows.
QAir flow to the windscreen and front
side window vents to demist or de-
frost them. IMPORTANTPressing one of these
buttons turns on (led on button itself on)
or off (led on button off) the associated
functions if the combination chosen is
among the 5 possible ones; if not it only
activates the main function of the button
pressed, without the possibility of turning
off with another press (at least in one dis-
tribution the air flow should be spread in
the passenger compartment).
To restore automatic air distribution con-
trol after a manual selection, press button
(13)
AUTO. fig. 104

GETTING TO KNOW YOUR CAR
100
turns on, or press button (13)AUTO; in
which case, however, the other manual
settings set will be cancelled.
CLIMATE CONTROL
COMPRESSOR ON/OFF
ENABLE BUTTON
(fig. 105)
Pressing button (14)
√enables the
turning on of the climate control compres-
sor. This condition is shown by the lighting
up of the led on the button itself.
When the climate control compressor is
turned off, the leds on buttons (13)
AUTO
and (14)√go off; automatic inside air
re-circulation control is also excluded (both
leds off on button 8
v) which always
stays off to prevent misting the windows;
even if unadvisable, it is still possible to
restore automatic operation of inside air
re-circulation pressing button (8)
v.
With the climate control compressor off,
it is not possible to admit air to the pas-
senger compartment with a temperature
below the outside temperature; in this
case, the value flashes on the display con-
cerning the temperature that cannot be
reached and the left led on button (13
AUTO- fig. 106) goes off.
The switching off of the climate control
compressor remains in storage even when
the engine has been stopped. To restore
automatic control for switching on the cli-
mate control compressor, press button
(14)
√again, the led on the buttonOperation of the climate
control compressor is nec-
essary for cooling and de-
humidifying the air; it is advisable
to keep this function always on, to
prevent window misting problems.
A0A0210b
A0A0211bfig. 105
fig. 106

GETTING TO KNOW YOUR CAR
101
INSIDE AIR RE-CIRCULATION
ON/OFF BUTTON
(fig. 107)
Inside air re-circulartion is controlled
according to three operating logics:
- automatic control, indicated by the
turning on of the right led on the button;
- forced engagement (inside air re-circu-
lation always on), indicated by the turning
on of the left led on the button (and by
the right led going off at the same time);
- forced switching off (inside air re-circu-
lation always off with air inlet from out-
side), indicated by the turning off of both
leds.
These operating conditions are obtained
pressing in sequence the inside air re-cir-
culation button (8)
v.
When inside air re-circulation is con-
trolled automatically by the system, the
right led on the air re-circulation button
(8)
vstays on all the time and the left
led shows the air re-circulation condition:
on= air re-circulation operating;
off= air re-circulation off.
If inside air re-circulation has been turned
on or off manually, the led on button
(13)
AUTOturns off. In automatic operation , inside air re-cir-
culation is turned automatically when the
antipollution sensor detects the presence
of polluted air, for example in cities,
queues, tunnels and operation of the
windscreen washer (with the typical smell
of spirits). The inside air- re-circula-
tion system makes it pos-
sible to reach the required
“heating” or “cooling” conditions
faster. It is however inadvisable to
use it on rainy/cold days as it
would considerably increase the
possibility of the windows misting
inside, especially if the climate con-
trol system is off.
A0A0212b
With low external tem-
perature the climate con-
trol compressor is unable
to work. It is therefore inadvisable
to use the inside air recirculation
function
vwith low outside tem-
perature as windows may mist
over quickly.
fig. 107

GETTING TO KNOW YOUR CAR
102
It is advisable to turn on
the inside air re-circulation
system in queues or tunnels
to avoid admitting polluted air from
outside. The prolonged use of this
function should however be avoid-
ed, especially with several persons
on board, to avoid the possibility of
the windows misting inside.
AUTOMATIC OPERATION AUTO
BUTTON
(fig. 108)
Pressing the (13)
AUTObutton the sys-
tem automatically adjusts the amount and
distribution of the air admitted to the pas-
senger compartment, cancelling all the
previous manual adjustments.
This condition is indicated by the lighting
up of both leds on the button itself. When the right led, on button (13)
AUTO
is off, this means that one or more manual
operations have been carried out and there-
fore automatic control is not complete
(except temperature control which is always
automatic) indicated by the left led on, or
that the system is in the
OFFcondition. In certain weather condi-
tions (e.g.: outside tem-
perature around 0°C) and
with automatic air re-circulation
control on, mist may form on the
windows. In this case press the in-
side air re-circulation button (8)
v, to switch off re-circulation
(leds on button off) and if neces-
sary increase the flow of air to the
windscreen.
A0A0209b
fig. 108