service Alfa Romeo GT 2008 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
74
BRAKE PAD WEAR
With the brake pedal pressed, the display
will show message + symbol when front
brake pads are worn; in this case have them
changed as soon as possible.
IMPORTANTSince the car is fitted with
wear sensors for the front brake pads, when
changing them, check also the rear brake
pads.
SELESPEED
TRANSMISSION
FAILURE
(2.0 T.SPARK
Selespeed versions)
On versions with Selespeed transmission,
message + symbol are displayed when there
is a failure in the Selespeed transmission. In
the event of Selespeed transmission failure,
go as soon as possible to the nearest Alfa
Romeo Authorized Services and have the
system checked.
ENGINE CONTROL
SYSTEM FAILURE
(EOBD) (amber)
(upon request for versions/
markets where applicable)
In normal conditions, turning the ignition
key to MAR, the warning light turns on,
but it should go off when the engine has
started. The initial turning on indicates that
the warning light is working properly.
If the warning light stays on or turns on
when travelling (together with message +
symbol on the display):
glowing steadily- means a fault in the
supply/ignition system which could cause
high emissions at the exhaust, possible lack
of performance, poor handling and high con-
sumption levels. In these conditions it is pos-
sible to continue driving without however re-
quiring heavy effort or high speed from the
engine. Prolonged use of the car with the
warning light on may cause damages. Con-
tact Alfa Romeo Authorized Services as soon
as possible. The warning light goes off if the
fault disappears, but it is however stored by
the system;
SEAT BELTS NOT
FASTENED (red)
The warning light turns on glowing steadi-
ly with ignition key at MAR, when the dri-
ver’s seat belt is not fastened correctly.
INCOMPLETE DOOR
LOCKING
Message + symbol are displayed when
one or more doors or the bonnet are not
properly shut.
´
t
U

GETTING TO KNOW YOUR CAR
75
ALFA ROMEO CODE
SYSTEM
Turning the key to MARthe symbol on
the display shall flash only once and then
go off. If with the ignition key at MAR, the
symbol stays on the display (together wit
the message), this indicates a possible fail-
ure (see “Alfa Romeo CODE system”).
IMPORTANTThe turning on at the
same time of warning light
Uand sym-
bol
Yindicates a failure of the Alfa Romeo
CODE system.
If with the engine running, the display
shows message + symbol, this means that
the car is not protected by the engine im-
mobilising device (see “Alfa Romeo CODE
system” in this section). Contact Alfa Romeo
Authorized Services to have all the keys
memorised.
GLOW PLUG
WARMING
(diesel versions)
GLOW PLUG WARMING
FAILURE (diesel versions)
Glow plug warming
Turning the ignition key to MAR, the dis-
play shows message + symbol. The symbol
will turn off when glow plugs reach the pre-
set temperature. Start the engine immedi-
ately after the symbol turns off.
IMPORTANTWith mild or hot ambient
temperature, warning light stays on for very
short time. flashing- indicates the possibility of dam-
age to the catalyst (see “EOBD system” in
this section). If the light flashes, it is nec-
essary to release the accelerator pedal to
lower the speed of the engine until the warn-
ing light stops flashing; continue the journey
at moderate speed, trying to avoid driving
conditions that may cause further flashing
and contact Alfa Romeo Authorized Services
as soon as possible.
Y
If, turning the ignition key
to MAR, the warning light
Udoes not turn on or if it
turns on glowing steadily or flash-
ing when travelling, contact Alfa
Romeo Authorized Services as
soon as possible.
m

GETTING TO KNOW YOUR CAR
76
WATER IN DIESEL
FUEL FILTER
(diesel versions)
Message + symbol are displayed when
travelling to indicate that there is water in
the diesel fuel filter.
DIESEL PARTICULATE
FILTER CLOGGED
(diesel versions)
(upon request for
versions/markets
where applicable)
Message + symbol are displayed when the
diesel particulate filter is clogged and the dri-
ving conditions do not enable to activate au-
tomatically the reclaiming procedure.
To enable the cleaning procedure, keep the
car running until the message + symbol turn
off. Glow plug warming failure
Message + symbol are displayed when
there is a failure in the glow plug warming
system. Contact Alfa Romeo Authorized Ser-
vices as soon as possible to have the fault
eliminated.
ch
The presence of water in
the fuel circuit may cause
serious damage to the en-
tire injection system and cause ir-
regular engine operation. If mes-
sage + symbol are displayed on the
reconfigurable multifunction display
contact Alfa Romeo Authorized
Services as soon as possible to
have the system relieved. If the
above indications come on immedi-
ately after refuelling, water has
probably been poured into the
tank: turn the engine off immedi-
ately and contact Alfa Romeo Au-
thorized Services.

GETTING TO KNOW YOUR CAR
77
INEFFICIENT ABS
SYSTEM (where
provided) (amber)
Turning the ignition key to MARthe warn-
ing light turns on, but it should go off after
few seconds.
The warning light turns on (together with
message + symbol on the display) when the
system is inefficient. In this case the brak-
ing system keeps its effectiveness un-
changed, but without the potential offered
by the ABS system.
Caution is advisable, particularly in all cas-
es of less than perfect grip. It is necessary
to contact Alfa Romeo Authorized Services
as soon as possible.
INEFFICIENT EBD
ELECTRONIC
BRAKING
DISTRIBUTOR (red)
(amber)
The turning on at the same
time of warning lights
xand>(togeth-
er with message + symbol on the display)
with the engine running indicates an EBD
system failure; in this case heavy braking
may cause the rear wheels to lock before
time, with the possibility of skidding.
Drive with the utmost care to the nearest
Alfa Romeo Authorized Service to have the
system checked.
INERTIAL FUEL
CUT-OFF SWITCH
Message + symbol are displayed when the
inertial fuel cut-off switch is triggered.
s>x
>
If after the message you
smell fuel or see leaks from
the fuel system, do not re-
set the switch to avoid fire risk.

GETTING TO KNOW YOUR CAR
78
VDC SYSTEM
(where provided)
(amber)
Turning the ignition key to MARthe warn-
ing light turns on, but it should go off after
few seconds.
If the warning light does not turn off or
stays on when travelling (together with mes-
sage + symbol on the display), contact Al-
fa Romeo Authorized Services.
The warning light flashes when the VDC
system cuts in.
ASR (WHEEL
ANTISKID SYSTEM)
(where provided)
(amber)
Turning the ignition key to MAR, the
warning light turns on, but it should go off
after few seconds.
The warning light turns on when the sys-
tem is switched off. The warning light flash-
es when the system cuts in, to alert the dri-
ver that the system is adapting to the road
surface grip conditions.
The turning on of the warning light (to-
gether with message + symbol on the dis-
play) also indicates a failure of the ASR sys-
tem. In this case contact Alfa Romeo Au-
thorized Services as soon as possible.
FRONT
PASSENGER’S AIR
BAG DEACTIVATED
(amber)
(upon request for
versions/markets where
applicable)
With passenger’s front air bags ON, turn-
ing the ignition key to MARthe warning
light turns on, but it should go off after about
4 seconds.
The warning light turns on when the pas-
senger’s front Air bag is deactivated.
FáV
Warning light Findi-
cates also warning light
¬
failures. This is indicated by
intermittent flashing, over 4 sec-
onds, of warning light
F. In this
event warning light
¬could not in-
dicate safety system failures. Con-
tact Alfa Romeo Authorized Ser-
vices to have the system checked
immediately.

GETTING TO KNOW YOUR CAR
80
WARNING LIGHTS
FAILURE
The message will be displayed when one
of the following warning lights is failing: ABS
warning light, EBD warning light, ASR warn-
ing light, VDC warning light.
ENGINE OIL
LEVEL SENSOR
The warning light turns on when a fault
is detected to the engine oil level sensor.
Contact Alfa Romeo Authorized Services as
soon as possible to have the failure elimi-
nated.
SPEED LIMIT EXCEEDED
The display will show the dedicated mes-
sage + symbol and the buzzer will sound
when the car exceeds the speed limit set
previously (see “Reconfigurable multifunc-
tion display”).
RANGE (Trip Computer)
The display will show the dedicated mes-
sage + symbol when the cruising range is
less than 50 km.
SCHEDULED SERVICING
The display will show the dedicated mes-
sage starting from 2000 km from the dead-
line planned in the Service Schedule. The
message will be repeated every 200 km
when turning the ignition key to MAR.
POSSIBLE
PRESENCE
OF ICE
ON THE ROAD
The display shows message + symbol √and a buzzer will sound when the outside
temperature reaches or falls below 3°C to
warn the driver of the possible presence of
ice on the road.
The buzzer will sound for approx. 2 sec-
onds whereas the message will stay on the
display for aprrox. 10 seconds then, only
the symbol will stay displayed until tem-
perature exceeds 6°C or until the engine
is switched off.
If when travelling, next to the indication
of possible ice on road, the temperature will
raise above 6° C symbol
√will turn off. If
temperature falls again below 3° C a new
message (outside temperature flashing) +
symbol
√will be displayed together with
the sound of the buzzer.
√

GETTING TO KNOW YOUR CAR
88
HEATING (fig. 95)
To obtain the temperature required, pro-
ceed as follows:
- temperature adjustment knob pointer
(1) on the red sector as required;
- air quantity adjustment knob pointer
(2) on the fan speed required to person-
alise the amount of air admitted;
- air distribution knob pointer (3) on the
required position.
To obtain the maximum heating power
proceed as follows:
- knob pointer (1) as far as it will go clock-
wise (maximum temperature red sector);
- knob pointer (2) on maximum fan
speed;
- air distribution knob pointer (3) on the
required position (position
w) is recom-
mended.
IMPORTANTTo be able to obtain sat-
isfactory passenger compartment warm-
ing, the engine should have reached nor-
mal operating temperature. The filter has the specific capability of fil-
tering external air, thus admitting to the
passenger compartment purified air, free
from particles such as dust, pollen, etc.
In addition to the above mentioned func-
tions, is also reduces the concentration of
pollutants.
The filtering action is active in all air inlet
conditions and it is clearly more effective
with the windows closed.
Have the conditions of the filter checked
at least once a year, preferably at the
onset of summer by Alfa Romeo
Authorised Services. If the car is habitually used in dusty or
polluted areas, the filter should be
checked and replaced at shorter intervals
than those specified in the Programmed
Maintenance Schedule.
If the filter is not replaced
the efficiency of the cli-
mate control system may
be seriously compromised up to
blocking the air flow at the outlets
and vents.
POLLEN FILTER
(for versions/markets where applicable)
A0A0734b
fig. 95

GETTING TO KNOW YOUR CAR
104
WING MIRROR AND
REARSCREEN
DEFROSTING/DEMISTING
BUTTON
(fig. 110)
Pressing button (9)
(turns on
demisting/defrosting of the rearscreen
and, if present, the wing mirror coils.
The turning on of this function is shown
by the turning on of the led on the button.
This function is timed and switches off
automatically after 20 minutes, or press-
ing the button again; the function is also
switched off when the engine is stopped
and will not be switched on again the next
time the engine is started.
IMPORTANTThe system automatical-
ly turns on rearscreen heating if the tem-
perature is below 3°C.
IMPORTANTDo not apply stickers on
the inside of the rearscreen over the heat-
ing filaments to avoid damage that might
cause it to stop working properly.
POLLEN FILTER
Have the conditions of the filter checked
by Alfa Romeo Authorised Services at least
once a year, preferably at the onset of
summer.
If the car is used mainly in dusty or pol-
luted areas it should be checked and, if
necessary, replaced at shorter intervals.
A0A0214b
The filter has the specific capability of fil-
tering external air, thus admitting to the
passenger compartment purified air, free
from particles such as dust, pollen, etc.
In addition to the above mentioned func-
tions, is also reduces the concentration of
pollutants.
The filtering action takes place under all
air inlet conditions and it is clearly most
effective with the windows shut.If the filter is not replaced
the efficiency of the cli-
mate control system may
be seriously compromised up to
blocking the air flow at the outlets
and vents.
fig. 110

GETTING TO KNOW YOUR CAR
108
The wheels should be
locked after a few clicks of
the hand brake. If it does
not occur contact Alfa Romeo Au-
thorised Services to have the hand
brake adjusted.
HAND BRAKE (fig. 115)
The hand brake lever is located between
the two front seats.
To operate the brake when the car is sta-
tionary, pull lever (A) upwards, until the re-
quired braking action is obtained.
When the ignition key is at MAR, the
warning light on the instrument cluster
x
will come on.
fig. 115
A0A0620b
Adjust the beams every
time the load carried
changes.
Correct positions as a function of the load:
– position 0: one or two people occupy-
ing the front seats
– position 1: five people;
– position 2: five people + load in the
boot;
– position 3: driver + 350 Kg load all
stowed in luggage com-
partment
fig. 114
A0A1106b
HEADLIGHT AIMING DEVICE
(fig. 114)
The headlights should be aimed correctly
depending on the car load.
For the required adjustment (only possible
with low beams on), press buttons
▲/▼:
– press button
▲, to increase by one po-
sition (e.g.: 0
➟1➟ 2➟3);
– press button
▼to decrease by one po-
sition (e.g.: 3
➟2➟1➟0);
The display (A), in the tachometer shows
positions during adjustment.
Xenon headlights aiming is automatic, ver-
sions with this optional are therefore not fit-
ted with headlight aiming device.

GETTING TO KNOW YOUR CAR
111
SYSTEM ACTIVATION
IMPORTANTOpening the driver’s door,
the Selespeed starts the hydraulic part of
the system to prepare it for the engine to be
started.
Turning the ignition key to MAR, all the
segments of the display (fig. 119), the
gearbox warning light (fig. 120) and the
wordCITYturn on. After about one second,
the display indicates the gear engaged (N,
1,2,3,4,5,R).
IMPORTANTIf after 10 seconds the dis-
play segment do not display the gear en-
gaged or the warning light stays on, turn the
ignition key to STOPand wait for the dis-
play to go off, then repeat the system acti-
vation procedure. If the fault persists, con-
tact Alfa Romeo Authorized Services. With gearshift to CITYgears can be shift-
ed manually using both the gearshift lever
or the steering wheel controls. Gearshift
stays in CITY.
The gear selected (fig. 119) is always
displayed regardless of the mode being se-
lected selected .
N= neutral;
1= first gear;
2= second gear;
3= third gear;
4= fourth gear;
5= fifth gear;
R= reverse. InCITYorSPORT, the selected mode is
also displayed.
IMPORTANT SPORTmode can only
be activated after deactivating the CITY
mode.
A warning light, a message (fig. 120)
and a buzzer draw the attention of the dri-
ver in the event of a fault at Selespeed trans-
mission.
The Selespeed considerably simplifies use
of the car, reducing the fatigue of city dri-
ving or when frequent gearshifting is re-
quired, at the same time offering brilliant
performance.
fig. 120
A0A9081g