key Alfa Romeo GT 2010 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
48
At each start, the rain sensor automatically
stabilises at a temperature of about 40°C
to eliminate any condensation from the con-
trol surface and prevent the formation of ice.
The rain sensor is able to detect and au-
tomatically adapt to the presence of the fol-
lowing particular conditions which require
different sensitivity:
– impurities on the control surface (salt,
dirt, etc.);
– streaks of water caused by worn wiper
blades;
– difference between day and night (the
human eye is more disturbed during the
night by the wet glass surface). Rain sensor (fig. 64)
The rain sensor (A), fitted only on cer-
tain versions, is an electronic device com-
bined with the windscreen wiper which has
the purpose of automatically adjusting the
number of wipes during intermittent opera-
tion to the intensity of the rain.
All the other functions controlled by the
right-hand lever remain unchanged.
The rain sensor is activated automatically
moving the right-hand lever to position (B-
fig. 62) and it has a range of adjustment
that gradually varies between wiper sta-
tionary (no wiping) when the windscreen is
dry, to wiper at first continuous speed (con-
tinuous, slow) with heavy rain.Turning the knurled ring (F-fig. 62) it
is possible to increase the sensitivity of the
rain sensor, obtaining a quicker change from
stationary, when the windscreen is dry, to
first continuous speed (continuous, slow).
Operating the windscreen washer with the
rain sensor activated (lever at position B)
the normal washing cycle is performed at
the end of which the rain sensor resumes its
normal automatic function.
Turning the ignition key to STOPthe rain
sensor is deactivated and the next time the
engine is started (MARposition) it will not
be reactivated even if the lever has remained
in position (B). In this case to activate the
rain sensor, simply move the lever to (A)
or (C) and then back to (B).
When the rain sensor is reactivated in this
way, the wiper performs at least one stroke,
even if the windscreen is dry, to indicate that
reactivation has occurred.
The rain sensor is located behind the inner
rear-view mirror in contact with the wind-
screen and inside the area cleaned by the
wiper and it controls an electronic control
unit which in turn controls the wiper motor.
fig. 64
A0A0331b

GETTING TO KNOW YOUR CAR
50
TO MEMORISE
THE SPEED
Move the ring (A) to ONand take the car
to the required speed normally. Turn the ring
(B) to (+) for at least three seconds, then
release it. The car speed is memorised and
it is therefore possible to release the accel-
erator pedal.
The car will continue to travel at the mem-
orised constant speed until one of the fol-
lowing conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or ESP system cuts in;
– with Selespeed transmission if a gear is
changed;
– inadvertent movement of the Selespeed
gear control lever to position N.
IMPORTANTIn the case of need (when
overtaking for instance) acceleration is pos-
sible simply pressing the accelerator pedal;
later, releasing the accelerator pedal, the car
will return to the speed memorised previ-
ously.
TO RESET THE
MEMORISED SPEED
If the device has been disengaged for ex-
ample pressing the brake or clutch pedal,
the memorised speed can be reset as fol-
lows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time
of speed memorising (4th, 5th or 6th
speed);
– press the RESbutton (C).
TO INCREASE THE
MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then mem-
orising the new speed reached (turning the
ring to (B) for more than three seconds);
or
2) momentaneously turning the ring (B)
to (+): each pulse of the ring will correspond
to a slight increase in speed (about 1.5
km/h) while pressing continuously will cor-
respond to a continuous speed increase. Re-
leasing the ring (B) the new speed will be
memorised automatically. –ONis the normal operating position of
the device. When the ring (A) is in this
position, the warning light
Üon the in-
strument cluster turns on.
Ring (B) serves for memorising and main-
taining the car sped or for increasing or low-
ering the speed memorised.
Turn the ring (B) to (+) to memorise the
speed reached or increase the speed mem-
orised.
Turn the ring (B) to (–) to lower the speed
memorised.
Each time the ring is actuated (B) the speed
increases or lowers by about 1.5 km/h.
Keeping the ring turned the speed changes
continuously. The new speed reached will
be maintained automatically.
TheRESbutton (C) resets the memorised
speed.
IMPORTANTTurning the ignition key to
STOPor the ring (A) to OFF, the speed
memorised is cleared and the system is
switched off.

GETTING TO KNOW YOUR CAR
52
fig. 67
A0A0748b
DASHBOARD
(For right-hand drive versions see dashboard and instruments in the dedicated paragraph at the end of the manual)
1. Adjustable side air vents - 2. Fixed side window air vents - 3. External lights control lever - 4. Instrument panel - 5. Tailgate release button - 6. Cards holder
(for versions/markets where applicable) - 7. Sound system (for versions/markets where applicable) - 8. Adjustable central air vents - 9. Upper fixed vent - 10.
Glass/can holder (for versions/markets where applicable) - 11. Front fog light button - 12. Hazard light switch - 13. Rear fog light button - 14. front passen-
ger’s air bag - 15. Glovebox - 16. Door locking button - 17. Heating/ventilation/climate controls - 18. Cigar lighter/ashtray housing lid - 19. Temperature sen-
sor - 20. Windscreen wiper stalk - 21. Ignition key and ignition switch - 22. Horn - 23. Steering wheel locking/release lever - 24. Driver’s air bag - 25. Set of
controls - 26. Bonnet opening lever.

GETTING TO KNOW YOUR CAR
57
FUEL LEVEL GAUGE WITH
RESERVE INDICATOR
This shows the amount of fuel left in the
fuel tank.
0- tank empty.
1- tank full (see the indications given in
paragraph “At the filling station").
The warning light
K(A-fig. 76) turns on
to indicate that approx. 7 litres of fuel are
left in the tank.
IMPORTANTThe pointer can reach the
red area also for a sum of unfavourable con-
ditions, i.e.: slow speed, uphill, fully laden
or towing a trailer with hot outside tempera-
ture.
IMPORTANTRefuelling shall always be
performed with engine off and ignition key at
STOP. If the engine is off but the key is at
MAR, a wrong fuel level could temporarily
be indicated. This is due to the internal sys-
tem control logic and cannot be considered as
a system malfunctioning.
ENGINE COOLANT FLUID
TEMPERATURE GAUGE WITH
MAXIMUM TEMPERATURE
WARNING LIGHT
This shows the temperature of the engine
coolant fluid and begins when the fluid tem-
perature exceeds approx. 50°C.
Normally the pointer should be towards
the middle of the scale. If the pointer reach-
es the higher temperatures of the scale (red
section, or white on certain versions) the re-
quest for car performance should be de-
creased.
The turning on of the
u(B-fig. 76)
warning light (on some versions together
with the message shown on the reconfig-
urablemultifunctiondisplay) indicates that
the coolant fluid temperature is too high;
in this case, stop the engine and contact
Alfa Romeo Authorised Services.IMPORTANTThe temperature of the en-
gine coolant may rise towards the maximum
values (red section, or white on certain ver-
sions) when the car is driven at low speeds,
especially when the ambient air tempera-
ture is high. In this case it is advisable to
stop the car and switch off the engine for
a few minutes, after which the journey can
be resumed, preferably at a higher speed.
fig. 76
A0A0758b

GETTING TO KNOW YOUR CAR
58
DIGITAL MULTIFUNCTION DISPLAY (where fitted)
The digital multifunction display shows the following: clock, outside temperature, buzzer setting (buzzer on/off), rheostat (light adjustment),
condition of the inertial fuel cut-off switch (FPS on).
CONTROL BUTTONS (fig. 75)
To make use of the information the digital display (with the ignition key at MAR) is able to give, you should firstly familiarise with the con-
trol buttons on the plate at the side of the steering column, using them as described in the following paragraphs. Before doing anything at all,
you are advised to read this chapter in full.
To decrease the value displayed
To decrease the value displayed Press for less than 1 second (pulse), indicated with
Qin the following de-
scriptions, to access the various adjustments
Press for more than 2 seconds, indicated with
Rin the following descriptions,
to confirm the choice required and return to the previous display
fig. 75
A0A1105b

GETTING TO KNOW YOUR CAR
63
Engine oil level check
(JTD versions)
Turning the ignition key to MARthe dis-
play shows the engine oil level for a few sec-
onds. During this phase, to clear the display
and move to next screen, press briefly but-
tonMODE.
IMPORTANTTo make sure that the en-
gine oil level displayed is correct, carry out
the check with the car on level ground.
Fig. 85refers to the correct engine oil
level display. As the oil level gradually falls,
the full bars go off leaving room for the emp-
ty ones.
fig. 85
A0A9101g
fig. 86
A0A9102g
fig. 87
A0A9103g
Fig. 86refers to the display with an oil
level below the preset minimum. In this con-
dition the bars are all empty.
IMPORTANTIn this case the correct en-
gine oil level should be restored as soon as
possible, see “Checking levels” in section
“Car maintenance”. Fig. 87refers to the display with an oil
level above the preset maximum. In this con-
dition the bars are all full.
IMPORTANTIn this case, contact Alfa
Romeo Authorised Services who will restore
the correct engine oil level.

GETTING TO KNOW YOUR CAR
68
BUZZER
This option enables to adjust the volume
of the roger-beep accompanying the acti-
vation of the car buttons and any fail-
ure/warning indication shown on the dis-
play.
To adjust the volume proceed as follows:
❒press briefly button MODE: the display
will show the previously set volume
“level”;
❒press buttons ▲/▼for setting;
❒press briefly button MODEto go back
to the menu screen or press the button
for long to go back to the standard
screen.
IMPORTANTIn the buzzer OFFcon-
dition, any buzzer failure warnings are main-
tained.
SERVICE
Through this function it is possible to dis-
play information connected to proper car ser-
vicing.
To consult this function, proceed as follows:
❒press briefly button MODE: service in
“km” or “mi” according to previous
setting, will be displayed (see para-
graph “UNITS”);
❒press buttons ▲/▼to display the re-
quired service info;
❒press briefly button MODEto go back
to the menu screen or press the button
for long to go back to the standard
screen.
IMPORTANTThe Service Schedule in-
cludes car maintenance every 20,000 km;
this is shown automatically, with the igni-
tion key to MAR, starting from 2,000 km
(or mi) from this deadline and it will be dis-
played again every 200 km. The display can
only be reset by Alfa Romeo Authorized Ser-
vices.
MENU OFF
Selecting this option will bring back to stan-
dard screen.
❒press briefly button MODEto select
the consumption unit (or press the but-
ton for long to go back to the standard
screen);
❒If the distance unit set is “km”, the dis-
play will show “l/100km” or
“km/l”: press buttons
▲/▼for set-
ting. If the distance unit set is “mi”, the
display will show “mpg”;
❒press briefly button MODEto go back
to the menu screen or press the button
for long to go back to the standard
screen.
IMPORTANTThe temperature unit (°C
or °F) set on the display is also shown on
the displays of the two-zone climate control
(where provided) and radionavigator (where
provided).

GETTING TO KNOW YOUR CAR
71
SET BUTTON
This button, set on the right steering col-
umn stalk (fig. 86), shall be used (with
ignition key MAR), to enter the GENERAL
TRIP and TRIP B functions.
ButtonSETshall also be used to reset the
GENERAL TRIP and TRIP B functions to start
a new mission:
-short push: to go to next screen;
-long push: to reset and then start a
new mission. Start of journey procedure
(reset)
With ignition key at MAR, press and keep
buttonSETpressed for over 2 seconds to
reset.
The reset operation (button SETpressed
for over 2 seconds) in the presence of the
screens concerning the GENERAL TRIP makes
it possible to reset also the TRIP B.
The reset operation (button SETpressed
for over 2 seconds) in the presence of the
screens concerning only the TRIP B makes
it possible to reset only the information as-
sociated with this function.
IMPORTANTRANGE and ACTUAL CON-
SUMPTION information cannot be reset.
New mission(reset)
Reset can be:
❒“manual”: reset is performed by the dri-
ver by pressing for long button SET;
❒“automatic”: reset is performed when
the “travel distance” reaches 9999.9
km (or mi), when “travel time” reach-
es 99:59 (99 hours and 59 minutes)
or after disconnecting and then recon-
necting the battery.
fig. 86
A0A0021b

GETTING TO KNOW YOUR CAR
72
Handbrake on
The warning light turns on when the hand-
brake is on. HIGH ENGINE
COOLANT
TEMPERATURE (red)
Turning the ignition key to MARthe warn-
ing light turns on, but it should go off after
few seconds.
The warning light turns on (together with
message + symbol on the display) when the
engine is overheated: if the warning light
comes on when driving, stop the car leav-
ing the engine on and slightly accelerated
to further activate the circulation of the
coolant fluid.
If the warning light does not turn off with-
in the next 2 or 3 minutes, stop the engine
and contact Alfa Romeo Authorized Services.
WARNING LIGHTS
AND MESSAGES
IMPORTANTThe presence of warning
lights depends on the type of engine and
equipment with which the car is fitted.
LOW BRAKE FLUID
LEVEL (red)
HANDBRAKE
ON (red)
Turning the ignition key to MARthe warn-
ing light turns on, but it should go off after
few seconds.
Low brake fluid level
The warning light turns on (together with
message + symbol on the display) when the
level of the brake fluid in the reservoir falls
below the minimum level, due to possible
leak in the circuit.
x
If the warning light turns
on when travelling, check
that the handbrake is not
engaged. If the warning light stays
on with handbrake disengaged,
stop the car immediately and con-
tact Alfa Romeo Authorized Ser-
vices.
u

GETTING TO KNOW YOUR CAR
73
LOW ENGINE
OIL PRESSURE
Message + symbol are displayed when en-
gine oil pressure is low.
LOW BATTERY
CHARGE
Message + symbol are displayed when the
battery charge is low.
If message + symbol are displayed, con-
tact immediately Alfa Romeo Authorized Ser-
vices.
AIR BAG FAILURE
(red)
Turning the ignition key to MARthe warn-
ing light turns on, but it should go off after
few seconds.
The warning light stays on glowing steadi-
ly if there is a failure in the air bag system.
¬vw
If when turning the igni-
tion key to MAR, the
warning light
¬does not
turn on or if it stays on when trav-
elling there could be a failure in
safety systems; in this event air
bags or pretensioners could not
trigger in case of impact or, in a mi-
nor number of cases, they could
trigger accidentally. Before restart-
ing contact Alfa Romeo Authorized
Services.
The failure of the warning
light
¬(warning light off)
is also indicated by the
flashing for more than the normal
4 seconds of the air bag warning
light
¬.
If message + symbol are
displayed when travelling
stop the engine immedi-
ately and contact Alfa Romeo Au-
thorized Services.