stop start Alfa Romeo MiTo 2009 Owner handbook (in English)

16GETTING TO KNOW YOUR CAR
Excessive engine coolant
temperature (red)
This warning light comes on when the ignition key is
turned to MAR, but it should go off after a few seconds.
The warning light turns on when the engine is overheated. The dis-
play will show the dedicated message.
If the warning light comes on, proceed as follows:
❍during normal travel: stop the car, stop the engine and check
that the water level in the reservoir is not under the MIN line.
In this case, wait for a few minutes for the engine to cool down,
then slowly and carefully open the cap, top-up with coolant and
check that the level is between the MIN and MAX references
on the reservoir. Also check for leaks. If the warning light comes
on again at the next engine start-up, contact your nearest Al-
fa Romeo Authorised Service.
❍In the case of demanding use (e.g. towing trailers uphill or
car at full load): slow down and stop the car if the warning light
stays on. Stop for 2 or 3 minutes with the engine running and
slightly accelerated to favour better coolant circulation. Then
stop the engine. Check the correct fluid level as described pre-
viously.
IMPORTANT Over demanding routes, it is advisable to keep the
engine on and slightly accelerated for a few minutes before switch-
ing it off.
u
Doors not closed correctly (red)
The warning light (or symbol on the display) lights up
when one or more doors or the boot tailgate are not
properly closed. A buzzer will sound when doors are open
and the car is moving. On some versions the warning light (or sym-
bol on the display) also lights up when the bonnet is not closed
correctly.´
Luggage compartment open
On some versions a message + symbol on the display
are shown when the luggage compartment is open.R
Bonnet open
On some versions a message + symbol on the display
are shown when the bonnet is open.S
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 16

EOBD/injection system failure
(amber)
Under normal conditions, the warning light comes on
when the ignition key is turned to MAR, but should go off
as soon as the engine is started.
If the warning light remains on or comes on whilst driving, this
means that the injection system is not working properly; in partic-
ular, if the warning light comes on constantly, this indicates a mal-
function in the supply/ignition system that could cause excessive
exhaust emissions, a possible loss of performance, poor driveabil-
ity and high fuel consumption.
On certain versions the dedicated message is displayed.
Under these conditions, the vehicle can continue travelling at mod-
erate speed without demanding excessive effort from the engine.
Prolonged use of the car with the warning light on may cause dam-
age. Contact your nearest Alfa Romeo Authorised Service as soon
as possible.
The warning light goes out after the fault is cleared, and the indi-
cation is stored in the system.
NOTE (this information applies
to petrol engine only)
If the warning light is flashing, this indicates that the catalytic
converter may be damaged.
If the warning light comes on intermittently, release the accelera-
tor pedal to lower the speed of the engine until the warning light
stops flashing; continue the journey at moderate speed, trying to
avoid driving conditions that may cause further flashing and con-
tact an Alfa Romeo Authorised Service as soon as possible.
GETTING TO KNOW YOUR CAR17
1U
Contact an Alfa Romeo Authorised Service as soon
as possible if the
Uwarning light does not light
up when the key is turned to MAR or if, while trav-
elling, the warning light comes on either steadily or blink-
ing (along with a message on the display). The opera-
tion of the warning light
Umay be checked by the traf-
fic police using specific devices. Follow the laws in force
in the country where you are driving.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 17

28GETTING TO KNOW YOUR CAR
WELCOME MOVEMENT
On some versions, when the key is turned to MAR, the following
occurs:
❍quick movement (up and down) of the speedometer and rpm
gauge;
❍illumination of graphic symbols/display;
❍an animated graphic representation of the vehicle profile ap-
pears on the display.
Gauge movement
❍If the key is removed from the ignition switch whilst the gauges
are moving, they immediately return to their initial position.
❍Once they have reached the end-of-scale values the gauges rest
on the value indicated by the vehicle.
❍The movement of the gauges stops when the engine is started.
Illumination of graphic symbols/display
A few seconds after the key is inserted, the gauges, graphic sym-
bols and display light up in sequence.
Display of graphic animation
When the key is removed from the ignition switch (with the doors
closed), the display remains lit up and shows a graphic animation.
The display illumination is then dimmed gradually until it goes
out completely.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 28

46GETTING TO KNOW YOUR CAR
SYMBOLS
Some vehicle components have coloured labels whose symbols in-
dicate precautions to be observed when using this component.
There is also a label under the bonnet that summarises all the sym-
bols.
ALFA ROMEO CODE SYSTEM
This is an electrical engine locking system which increases protec-
tion against an attempted theft of the car. It is automatically acti-
vated when the ignition key is extracted.
Each key contains an electronic device which modulates the sig-
nal emitted during ignition by an antenna built into the ignition de-
vice. This signal is the ‘password’ which changes at each ignition
and which the control unit uses to recognise the key and enable
ignition.
OPERATION
Each time the car is started by turning the ignition key to MAR, the
Alfa Romeo CODE system control unit sends an acknowledgement
code to the engine management control unit to deactivate the in-
hibitor.
The code is sent only if the Alfa Romeo CODE system control unit
has recognised the code transmitted from the key.
Each time the ignition key is turned to STOP, the Alfa Romeo
CODE system deactivates the functions of the engine management
control unit. If the code is not recognised correctly during ignition,
the
Ywarning light comes on in the instrument panel. In this
case turn the key to STOP and then to MAR; if the lock persists
try again with the spare set of keys. If you are still unable to
start the engine contact an Alfa Romeo Authorised Service.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 46

GETTING TO KNOW YOUR CAR55
1IGNITION DEVICE
The key can be turned to three different positions fig. 21:
❍STOP: the engine is off, the key can be extracted, the steer-
ing is locked. Some electrical devices (e.g. car radio, central
door locking system, alarm, etc.) are enabled;
❍MAR: driving position. All electrical devices are enabled;
❍AVV: engine start-up.
The ignition switch is fitted with an electronic safety system that
requires the ignition key to be turned back to STOP if the engine
will not start, before the starting operation can be repeated.
fig. 21A0J0031m
If the ignition switch is tampered with (e.g.:
attempted theft), have it checked over by an Alfa
Romeo Authorised Service as soon as possible.
Always remove the key when you leave your car
to prevent someone from accidentally operating
the controls. Remember to engage the handbrake.
Engage 1
stgear if the car is parked uphill or reverse if the
car is parked downhill. Never leave children unattended
in the car.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 55

74GETTING TO KNOW YOUR CAR
IMPORTANT the MAX-DEF function remains on for approximately
3 minutes from the moment the engine coolant reaches a suitable
temperature.
When the function is engaged the words FULL AUTO disappear from
the display. With the function activated the only possible manual
adjustments are the regulation of the fan speed and the disen-
gagement of the heated rear windscreen.
Pressing buttons B, C, F or AUTO switches off the MAX-DEF func-
tion and restores the previous settings.
DEMISTING/DEFROSTING OF HEATED REAR
WINDSCREEN AND DOOR MIRRORS
(where provided)
Press button G to activate heated rear windscreen demisting/de-
frosting. This function switches off automatically after about 20
minutes or when the engine is turned off. It is not switched on
automatically the next time the engine is started.
IMPORTANT Do not affix stickers to the inside of the rear window
over the heating filaments, to avoid damage that might cause them
to stop working properly. With climate control compressor off:
❍if the outside temperature is higher than the set one, the sys-
tem will not be able to satisfy the request. The temperature
value will then flash on the display for a few seconds and the
word AUTO will disappear;
❍the fan speed can be manually reset.
With the compressor on and the engine running, the fan speed can-
not be lower than one bar on the display.
RAPID WINDOW DEMISTING/DEFROSTING
(MAX-DEF function)
Press button F to activate rapid windscreen and side window demist-
ing/defrosting. The climate control system carries out the follow-
ing operations:
❍switches on the climate control compressor when climatic con-
ditions allow;
❍disables air recirculation;
❍sets maximum air temperature (HI) in both areas;
❍engages the fan at a speed based on the engine coolant tem-
perature;
❍directs air flow to the windscreen and front side window vents;
❍switches on the heated rear windscreen.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 74

GETTING TO KNOW YOUR CAR79
1
Moving the lever upwards (unstable position) limits operation to
the time the lever is held in this position. The lever will return to
position and the wiper will be automatically stopped when released.WINDOW WASHING
The right lever controls windscreen wiper/washer and heated rear
window wiper/washer operation.
WINDSCREEN WIPER/WASHER fig. 34
This only operates with the ignition turned to MAR. Selector wheel
A can take five different positions:
,intermittent (low speed);
Owindscreen wiper off;
AUTO rain sensor activation (where provided) (the windscreen
wipers adapt the operating speed automatically to suit the
intensity of the rain)
≤intermittent;
≥continuous slow;
¥continuous fast operation.
fig. 34A0J0064m
Do not use the windscreen wiper to remove lay-
ers of snow or ice from the windscreen. In such con-
ditions, the windscreen wiper may be subjected to
excessive stress and the motor protection which prevents
operation for a few seconds may trip. If operation is not
restored, even after turning the key and restarting the en-
gine, contact an Alfa Romeo Authorised Service.
“Smart washing” function
Pull the lever towards the steering wheel (unstable position) to op-
erate the windscreen washer jet. By keeping the lever pulled for
more than half a second, it is possible to operate the washer jet
and the wiper at the same time with just one movement.
The wiper stops working three strokes after releasing the lever. A
further stroke after approx. 6 seconds completes the wiping cycle.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 79

92GETTING TO KNOW YOUR CAR
ELECTRIC SUNROOF
(where provided)
The extensively glazed sun roof comprises a moving glass panel
and a sun blind. The glazed panel, when closed, allows light from
the outside to enter and makes it possible to see the outside from
the passenger compartment.
When it opens the front glass panel slides towards the outside of
the roof.
OPERATION
The sun roof is operated by pressing buttons A and B-fig. 53 located
on the trim next to the middle courtesy light.
The sun roof can only be operated with the ignition key in the MAR
position.
Roof opening
Pressing button A-fig. 53 allows two opening modes for the front glass
panel.
Automatic
If button A-fig. 53 is pressed for a while, the front glass panel is raised
from completely closed to the spoiler position. If the button is pressed
again, the panel starts to slide backwards until it is completely open.
After the initial opening command the glass panel can be stopped in
intermediate positions by pressing the button again.
Manual
If button A-fig. 53 is pressed briefly, the front glass panel moves from
the completely closed position and stops in the position where the but-
ton is released. In this case the panel opens by pressing the actual
button.
This function makes it possible to place the front panel in intermedi-
ate positions in relation to those produced through automatic open-
ing.
fig. 53A0J0329m
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 92

GETTING TO KNOW YOUR CAR93
1The sun roof must stay closed if a transverse roof
rack is fitted.Sun blind
The brightness in the passenger compartment can be adjusted by
using a sun blind.
To open/close the blind, grasp the handle C-fig. 53. The blind can
be closed irrespective of the opening position of the glass panel.
Roof closing
Pressing button B-fig. 53 allows two closing modes for the front
glass panel.
Automatic
With the roof completely open, press button B-fig. 53 for a while:
the front glass panel will assume the spoiler position.
If the button is then pressed, the panel will start to slide forward
until it is completely closed.
After the initial opening command, the glass panel can be stopped
in intermediate positions by pressing the button again.
Manual
If button B-fig. 53 is pressed briefly, the front glass panel moves
from the completely open position and stops in the position where
the button is released. In this case the panel closes by pressing
the actual button.
This function makes it possible to place the front glass panel in in-
termediate positions in relation to those produced through auto-
matic closing.
When leaving the car, always remove the key from
the ignition device to avoid the risk of injury due
to accidental operation of the sun roof; it presents
a risk to those left on board: improper use of the roof can
be dangerous. Before operation, always check that no-
one is at risk of being injured by the moving sun roof or
by objects getting caught and dragged by it.
Do not open the sun roof in the presence of snow
or ice: it may be damaged.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 93

GETTING TO KNOW YOUR CAR97
1
IMPORTANT If the anti-pinch protection intervenes 5 times consec-
utively within 1 minute or a system failure is detected, the auto-
matic window closing function is inhibited. The window can then
only be operated in steps of half a second and the button must
be released following each step.
One of the following manoeuvres must be carried out in order to
restore correct operation:
❍switch off and restart the engine;
❍fully lower the window concerned.
IMPORTANT With ignition key at STOP or removed, the electric win-
dows remain active for about 3 minutes and are deactivated the
moment a door is opened.
IMPORTANT Where the anti-crush safety device is present, when
button
Ëon the remote control is pressed for more than 2 seconds,
the windows are opened, whilst when button
Áis pressed for more
than 2 seconds the windows are closed.
Passenger-side door
The passenger-side door is equipped with a button that controls
the opening/closing of the passenger-side window.
The system conforms to the 2000/4/EC standard
concerning the safety of passengers leaning out of
the passenger compartment.
Incorrect use of the electric windows may be dan-
gerous. Before operation, always check that no
passenger is at risk of being injured directly by the
moving window or by objects getting caught in or dragged
by the window. When leaving the car, always remove the
key from the ignition device to avoid the risk of injury due
to accidental operation of the electric windows.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 97