window Alfa Romeo MiTo 2009 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2009, Model line: MiTo, Model: Alfa Romeo MiTo 2009Pages: 250, PDF Size: 4.61 MB
Page 75 of 250

74GETTING TO KNOW YOUR CAR
IMPORTANT the MAX-DEF function remains on for approximately
3 minutes from the moment the engine coolant reaches a suitable
temperature.
When the function is engaged the words FULL AUTO disappear from
the display. With the function activated the only possible manual
adjustments are the regulation of the fan speed and the disen-
gagement of the heated rear windscreen.
Pressing buttons B, C, F or AUTO switches off the MAX-DEF func-
tion and restores the previous settings.
DEMISTING/DEFROSTING OF HEATED REAR
WINDSCREEN AND DOOR MIRRORS
(where provided)
Press button G to activate heated rear windscreen demisting/de-
frosting. This function switches off automatically after about 20
minutes or when the engine is turned off. It is not switched on
automatically the next time the engine is started.
IMPORTANT Do not affix stickers to the inside of the rear window
over the heating filaments, to avoid damage that might cause them
to stop working properly. With climate control compressor off:
❍if the outside temperature is higher than the set one, the sys-
tem will not be able to satisfy the request. The temperature
value will then flash on the display for a few seconds and the
word AUTO will disappear;
❍the fan speed can be manually reset.
With the compressor on and the engine running, the fan speed can-
not be lower than one bar on the display.
RAPID WINDOW DEMISTING/DEFROSTING
(MAX-DEF function)
Press button F to activate rapid windscreen and side window demist-
ing/defrosting. The climate control system carries out the follow-
ing operations:
❍switches on the climate control compressor when climatic con-
ditions allow;
❍disables air recirculation;
❍sets maximum air temperature (HI) in both areas;
❍engages the fan at a speed based on the engine coolant tem-
perature;
❍directs air flow to the windscreen and front side window vents;
❍switches on the heated rear windscreen.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 74
Page 80 of 250

GETTING TO KNOW YOUR CAR79
1
Moving the lever upwards (unstable position) limits operation to
the time the lever is held in this position. The lever will return to
position and the wiper will be automatically stopped when released.WINDOW WASHING
The right lever controls windscreen wiper/washer and heated rear
window wiper/washer operation.
WINDSCREEN WIPER/WASHER fig. 34
This only operates with the ignition turned to MAR. Selector wheel
A can take five different positions:
,intermittent (low speed);
Owindscreen wiper off;
AUTO rain sensor activation (where provided) (the windscreen
wipers adapt the operating speed automatically to suit the
intensity of the rain)
≤intermittent;
≥continuous slow;
¥continuous fast operation.
fig. 34A0J0064m
Do not use the windscreen wiper to remove lay-
ers of snow or ice from the windscreen. In such con-
ditions, the windscreen wiper may be subjected to
excessive stress and the motor protection which prevents
operation for a few seconds may trip. If operation is not
restored, even after turning the key and restarting the en-
gine, contact an Alfa Romeo Authorised Service.
“Smart washing” function
Pull the lever towards the steering wheel (unstable position) to op-
erate the windscreen washer jet. By keeping the lever pulled for
more than half a second, it is possible to operate the washer jet
and the wiper at the same time with just one movement.
The wiper stops working three strokes after releasing the lever. A
further stroke after approx. 6 seconds completes the wiping cycle.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 79
Page 82 of 250

GETTING TO KNOW YOUR CAR81
1CRUISE CONTROL (where provided)
GENERAL INFORMATION
This is an electronic driving aid that allows you to drive at a speed
of above 30 km/h on long and straight dry roads (e.g. motor-
ways), at a preset speed without having to press the accelerator
pedal.
It is not recommended for use on extra-urban roads with traffic. Do
not use it in town.
DEVICE ENGAGEMENT
Turn selector wheel A-fig. 36 to ON. The device cannot be engaged
when the vehicle is in 1stgear or reverse: It is advisable to engage
the device at 5thgear or higher.
REARSCREEN WIPER/WASHER
(where provided)
Activation
This only operates with the ignition turned to MAR. The function
stops when the lever is released. Turning selector wheel B-fig. 34
from position
Oto position 'activates the rearscreen wiper ac-
cording to the following:
❍intermittent operation if the windscreen wiper is off;
❍synchronised with the windscreen wiper (but with half stroke
frequency);
❍continuous operation with reverse engaged and windscreen
wiper on.
With reverse gear engaged and windscreen wiper on, the rearscreen
wiper is activated in continuous mode. Pushing the lever towards
the dashboard (unstable position) will activate the rear window
washer jet.
Keeping the lever pushed for more than half a second will also
activate the rearscreen wiper. Releasing the lever will activate the
smart washing function as described for the windscreen wiper.
fig. 36A0J0065m
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 81
Page 97 of 250

96GETTING TO KNOW YOUR CAR
ELECTRIC WINDOWS
These are equipped with an automatic setting to raise and lower
the driver-side front window.
CONTROLS FOR
Driver’s door fig. 57
Buttons have been provided on the driver’s door panel to control
the following functions with the ignition turned to MAR:
A: opening/closing of left-hand window
B: opening/closing of right-hand window
Continuous automatic operation
(where provided)
This is activated by pressing one of the two buttons for longer than
half a second. The window will stop when it reaches the end of
travel or when the button is pressed again.
❍Driver’s side: raising/lowering
❍Passenger side: lowering only
❍Where the anti-crush safety device is present: driver’s side and
passenger side raising/lowering.
Anti-pinch safety device
(for versions/markets where provided)
The vehicle is equipped with an anti-pinch safety device for the
upwards motion of the windows.
This safety system is capable of recognizing the presence of an ob-
stacle whilst the window is closing; when this happens, the system
stops the travel of the glass and, depending on the position of
the window, reverses its movement.
This device is also useful when the windows are activated acci-
dentally by children on board the vehicle.
The anti-pinch function is active both during manual and automat-
ic operation of the electric windows. Following the intervention
of the anti-pinch system, the window travel is immediately inter-
rupted and subsequently reversed until the lower end of travel is
reached. During this time the window cannot be operated in any
way.
fig. 57A0J0023m
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 96
Page 98 of 250

GETTING TO KNOW YOUR CAR97
1
IMPORTANT If the anti-pinch protection intervenes 5 times consec-
utively within 1 minute or a system failure is detected, the auto-
matic window closing function is inhibited. The window can then
only be operated in steps of half a second and the button must
be released following each step.
One of the following manoeuvres must be carried out in order to
restore correct operation:
❍switch off and restart the engine;
❍fully lower the window concerned.
IMPORTANT With ignition key at STOP or removed, the electric win-
dows remain active for about 3 minutes and are deactivated the
moment a door is opened.
IMPORTANT Where the anti-crush safety device is present, when
button
Ëon the remote control is pressed for more than 2 seconds,
the windows are opened, whilst when button
Áis pressed for more
than 2 seconds the windows are closed.
Passenger-side door
The passenger-side door is equipped with a button that controls
the opening/closing of the passenger-side window.
The system conforms to the 2000/4/EC standard
concerning the safety of passengers leaning out of
the passenger compartment.
Incorrect use of the electric windows may be dan-
gerous. Before operation, always check that no
passenger is at risk of being injured directly by the
moving window or by objects getting caught in or dragged
by the window. When leaving the car, always remove the
key from the ignition device to avoid the risk of injury due
to accidental operation of the electric windows.
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 97
Page 99 of 250

98GETTING TO KNOW YOUR CAR
Electric window system initialisation
The safety system must be re-initialised after disconnecting the bat-
tery or if the relevant protection fuse is blown.
Initialisation procedure:
❍fully close the window to be initialised manually;
❍after the window has reached the upper end of travel, hold the
up button pressed for at least one second.
IMPORTANT For versions/markets where provided, following the
disconnection of the power supply (replacing or disconnecting the
battery or replacing the protection fuse for the electric windows
control units), the automatic setting for the electric windows must
be reset.The reset operation should be carried out with the doors closed
according to the following procedure:
1. completely lower the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached;
2. completely raise the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached;
3. repeat stages 1 and 2 for the passenger-side window
4. check that the initialisation has taken place correctly by check-
ing the automatic operation of the windows.
IMPORTANT With central locking on, operating the internal handle
of one of the doors will unlock all the doors. If there is no power
(blown fuse, battery disconnected, etc.) the doors can still be locked
manually. As in this case the automatic window opening function
is not available, to open or close the door with the window closed,
apply pressure to the window towards the vehicle interior (see fig.
58), to aid the passage of the window against the trim.
fig. 58A0J0170m
001-126 Alfa MiTo GB 13-11-2008 10:08 Pagina 98
Page 128 of 250

SAFETY127
2
Seat belts.................................................................... 128
S.B.R. system............................................................... 129
Pretensioners............................................................... 131
Carrying children safely................................................. 134
Fitting “Universal” child seat .......................................... 135
“Isofix” child restraint assembly setup .............................. 139
Front Airbags ............................................................... 142
Side Air bags (Side bag - Window bag) ............................ 145
“Alcohol Test” Kit ......................................................... 148
127-148 Alfa MiTo GB 12-11-2008 15:41 Pagina 127
Page 146 of 250

SAFETY145
2
SIDE AIRBAGS
(SIDE BAG - WINDOW BAG)
The car is fitted with front side bags for driver and passenger for
protecting the chest, and window bags for protecting front and rear
passengers’ heads.
FRONT SIDE BAGS fig. 18
These are comprised of two types of bag located in the front back
rests, which protect the chest area of passengers in the event of
a side impact of medium-high severity.
HEAD PROTECTION SIDE AIR BAGS
(WINDOW BAGS) fig. 19
These are comprised of two “curtain” bags located behind the side
cover of the roof and protected by dedicated covers. They protect
the heads of the front passengers in the event of a side impact.
The airbags are not deployed in the event of side impact of low
severity (for which the restraining action of the seat belts is suffi-
cient). It is therefore always necessary to wear seat belts.
In the event of a side impact, the system provides best protection
if the passenger sits on the seat in a correct position, thus allow-
ing correct window bag deployment.
fig. 18A0J0103mfig. 19A0J0051m
127-148 Alfa MiTo GB 12-11-2008 15:41 Pagina 145
Page 147 of 250

146SAFETY
A small amount of dust will be released when the airbags are de-
ployed: this is in no way toxic and does not indicate an outbreak
of fire. It may however irritate the eyes and skin: wash with mild
soap and water in the event of exposure.
Airbag checking, repair and replacement must only be carried out
by an Alfa Romeo Authorised Services.
If the vehicle is to be scrapped, contact an Alfa Romeo Authorised
Services to have the air bags deactivated.
Pretensioners and airbags are deployed according to different log-
ics on the basis of the type of collision. Non-deployment of one of
the devices does not necessarily indicate a system malfunction.Do not hook rigid objects to the clothes hangers or
support handles.
Do not rest your head, arms or elbows on the door,
windows or on the window bag area to avoid in-
juries during inflation.
Never lean your head, arms or elbows out of the
window.
IMPORTANT NOTES
Do not wash the seats with water or pressurised steam (wash by
hand or at automatic seat washing stations).
The front and /or side air bags may activate in the event of sharp
knocks to the underbody of the vehicle (e.g. impact with steps,
pavements, potholes or road bumps etc.).
If the ¬warning light does not turn on or if it
stays on when travelling (together with the mes-
sage on the multifunctional display, where pro-
vided) when turning the key to MAR, there could be a fail-
ure in the restraint systems. If this is the case, the airbags
or pretensioners do not trigger in the event of an impact
or, in a small number of cases, they may trigger acciden-
tally. Do not drive the vehicle and contact a Alfa Romeo
Authorised Services to have the system checked immedi-
ately.
127-148 Alfa MiTo GB 12-11-2008 15:41 Pagina 146
Page 159 of 250

158STARTING UP AND DRIVING
SNOW CHAINS
The use of snow chains should be in compliance with local regu-
lations. The snow chains may be applied only to the front wheel
tyres (drive wheels).
Check the tension of the chains after the first few metres have been
driven.
Use reduced bulk snow chains: for 195/55 R16” and 205/45
R17” tyres. Use reduced bulk snow chains with a maximum pro-
trusion from the tyres of 9 mm.
IMPORTANT The spare wheel cannot be fitted with snow chains.
If a front (drive) wheel is punctured and snow chains must be used,
you must remove a normal wheel from the rear and replace this
one with the small spare wheel. In this way, with two normal dri-
ve wheels, it is possible to use snow chains.
CAR INACTIVITY
If the car is to be left inactive for longer than a month, the following
precautions should be noted:
❍park the vehicle in a dry, covered and, if possible, ventilated
area; engage a gear and check that the handbrake is not en-
gaged;
❍disconnect the negative battery terminal and check battery
charge. Repeat this check once every three months during stor-
age;
❍clean and protect painted areas using protective wax;
❍clean and protect the shiny metal areas using special com-
mercially-available products;
❍sprinkle talcum powder on the rubber windscreen and rear win-
dow wiper blades and lift them off the glass;
❍slightly open the windows;
❍cover the car with a fabric or perforated plastic sheet. Do not
use compact plastic sheets which do not allow humidity to evap-
orate from the surface of the car.
❍inflate tyres to a pressure of +0.5 bar above the normal spec-
ified pressure and check the pressure at regular intervals;
❍if you have not disconnected the battery, check the battery
charge every thirty days;
❍do not drain the engine cooling system.
Keep your speed down when snow chains are fit-
ted. Do not exceed 50 km/h. Avoid potholes, steps
and pavements and also avoid driving long dis-
tances on roads not covered with snow to prevent dam-
aging the car and the roadbed.
149-158 Alfa MiTo GB 12-11-2008 15:41 Pagina 158