display Acura MDX 2008 Workshop Manual

Page 114 of 489

ÛÝÛÝ
Keyless Lock Acknowledgment
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the tailgate
arelockedandthesecuritysystem
has set (see page ). You can
customize the exterior lights not to
f lash and the beeper not to sound.
You can choose this customize item
f rom ‘‘DOOR/WINDOW SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
269
Multi-Inf ormation Display
110
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Page 115 of 489

ÛÝ
Security Relock Timer
If you unlock the doors and the
tailgate with the remote transmitter,
but do not open any of the doors or
thetailgatewithin30seconds,the
doors and the tailgate automatically
relock and the security system sets.
You can change this relock time
f rom 30 seconds to 60 or 90 seconds.You can choose this customize item
f rom ‘‘DOOR/WINDOW SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ and repeat
the procedure again.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
111
\f—\f—\fy\f
y
()-
\fy\f

y
2008 MDX

Page 116 of 489

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘SECURITY RELOCK TIMER’’ and
repeat the procedure again.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
112
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Page 117 of 489



ÛÝ µ

ÛÝ
CONT INUED
Here is one custom setting for the
wiper setup: Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. You can select from these two
settings when the wiper switch is in
the INT (intermittent) position:
INTERMITTENT The
intermittent operation varies
according to the selection you make
on the wiper lever’s intermittent
control ring.
WITH VEH SPD The intermittent
operation varies according to vehicle
speed.
While ‘‘WIPER SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode. WIPER ACTION
Wiper Action
Multi-Inf ormation Display
Wiper Setup
Inst rument s and Cont rols
113
INFO ( / )
BUTTON
SEL/RESET
BUTTON
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Page 118 of 489

ÛÝÛÝIf the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘WIPER ACTION’’ and repeat the
procedure again.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Press the SEL/RESET button to see
the selections.
You can choose this customize item
f rom ‘‘WIPER SETUP’’ by pressing
the INFO ( / ) button repeatedly.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
114
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Page 125 of 489

If you turn the ignition switch to the
LOCK (0) position with the
headlight switch on, but do not open
the door and get out, the lights turn
of f af ter 10 minutes (3 minutes, if
the switch is in the ‘‘AUTO’’
position).
The lights turn on again when you
unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
go of f . With the driver’s door open,
you will hear a lights-on reminder
chime.
This f eature turns of f the headlights,
all other exterior lights, and the
instrument panel lights within 15
seconds after you remove the key
and close the driver’s door.
To change the ‘‘HEADLIGHT AUTO
OFF TIMER’’ setting, see page .
The automatic lighting of f f eature
activates if you leave the headlight
switch in the ‘‘ ’’ or ‘‘ ’’
position or if the lights are turned on
by setting the switch in the ‘‘AUTO’’
position, and you remove the key,
then open and close the driver’s door.
If you see a ‘‘CHECK DRL
SYSTEM’’ message on the multi-
inf ormation display, there is a
problem with the daytime running
light system. Take your vehicle to a
dealer to have it checked.
When the multi-information display
shows a ‘‘DRL OFF’’ message, the
daytime running lights are of f .
Follow the procedure in the lef t
column to turn them on.
102
Headlights
Automatic Lighting Of f Feature
Inst rument s and Cont rols
121
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX

Page 127 of 489



µ´ µThe level of brightness is shown on
the multi-information display while
you adjust it. It goes out 5 seconds
af ter you f inish adjusting. To reduce glare at night, the
instrument panel illumination dims
when you turn the light switch to
or . To cancel the glare
reduction f unction, set the
brightness to the highest level, then
press the button. You will hear a
beep when it is canceled.
Youcancustomizewhentheglare
reduction f unction starts. To change
‘‘AUTO INTERIOR
ILLUMINATION’’, see page f or
more inf ormation.
Adjust the brightness of the
instrument panel by pressing the
or button. Press the button to
increase the brightness and the
button to decrease it. You can adjust
the brightness with the headlight
switch on or of f . 95
Instrument Panel Brightness
Inst rument s and Cont rols
123
\f—\f—\fy\f\fy
()-
\fy\f
y
2008 MDX

Page 138 of 489

Push the release lever to the right as
shown.
If you need to unlock the tailgate
manually, it means there is a
problem with the tailgate. Have the
vehicle checked by your dealer.
If you try to drive off with the
tailgate not closed completely, a
beeper sounds and a ‘‘DOOR &
TAILGATE OPEN’’ message is
shown on the multi-inf ormation
display.
Keep the tailgate closed at all times
while driving to avoid damaging the
tailgate and to prevent exhaust gas
f rom getting into the interior. See
on page
.
If there is a problem in the power
tailgate system, you will see a
‘‘CHECK POWER TAILGATE’’
message on the multi-inf ormation
display. Have the system checked by
your dealer.
With this message shown on the
multi-inf ormation display, you can
still open or close the tailgate
manually. If the power door lock system cannot
unlock the tailgate, unlock it
manually.
Use a small flat-tipped screwdriver to
remove the cover on the back of the
tailgate.
58U.S. Entertainment Packages and
Canadian Elite Package models
Unlocking the T ailgate
Carbon Monoxide Hazard
Tailgate
134
\f—\f—\fy\f
y
()-
\fy\f
y
2008 MDX

Page 143 of 489

Here are the settings activated with
the remote;Driving position memory
(see page ).
When you unlock the driver’s door
with your remote, each remote
activates the keyless memory
settings related to that remote. The
driver’s ID (MEMORY 1 or
MEMORY 2) is shown on the back
of each remote. When you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat (except
the power lumbar feature) and
outside mirrors start to move to the
positions stored in memory. The
indicator in the related memory
button to the remote comes on.Audio system settings
(see page ).
Climate control settings
(see page ).
Customized settings
(see page ).
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink once to indicate the
f eature has been turned on.
To turn of f this f eature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink twice. Then
release the buttons. Doing this
cancels the keyless memory settings
f or that remote and restores the
def ault settings.
You will also see the ‘‘WELCOME
DRIVER 1’’ or ‘‘WELCOME
DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
The steering wheel will move to the
stored position when you insert the
key into the ignition switch.
83
200 157
171
K eyless Memory Settings
Remote Transmitter
Inst rument s and Cont rols
139
TM
\f—\f—\fy\f\f
y
()-
\fy\f
y
2008 MDX

Page 157 of 489

You can open and close the
moonroof f or up to 10 minutes af ter
you turn of f the ignition switch.
Opening either f ront door cancels
this function.To apply the parking brake, push the
pedal down with your f oot. To
release it, pull the release handle
f ully. The parking brake indicator on
the instrument panel should go out
when the parking brake is f ully
released (see page ).
If the moonroof runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
moonroof , remove the obstacle, then
use the moonroof switch again.
Auto reverse stops sensing when the
moonroof is almost closed. You
should always check that all
passengers and objects are away
f rom the moonroof bef ore closing it.
You will also see a ‘‘RELEASE
PARKING BRAKE’’ message on the
multi-inf ormation display (see page). 65
81
CONT INUED
Parking Brake
Auto Reverse
Moonroof , Parking Brake
Inst rument s and Cont rols
153
RELEASE HANDLE
PARKING BRAKE PEDAL
Opening or closing the
moonroof on someone’s hands
or fingers can cause serious
injury.
Make sure all hands and fingers
are clear of the moonroof
before opening or closing it. If you try to open the moonroof in
below-f reezing temperatures, or when
it is covered with snow or ice, you can
damage the moonroof panel or its
motor.
\f—\f—\fy\f
y
()-
\fy\f
y
2008 MDX

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 71-80 81-90 91-100 ... 190 next >