Acura RDX 2008 Owner's Manual

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Open the hood.
1.
2. 3.
4.
5.
Headlight A iming
L ow Beam Headlight Bulb
Replacement
Replacing a High Beam Headlight
Bulb
Lights
Maint enance
347
BULB CONNECTORHalogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
\f—\f—\f
y


y
() 
\fy\fy
2008 RDX

Test the lights to make sure the
new bulb is working.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Remove the bulb f rom the socket
by pushing the bulb in and turning
it counterclockwise until it unlocks.
Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise. Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
1.
2.
3. 1.
2.
4.
5.
Lights
Replacing a Front T urn Signal/
Parking L ight Bulb
Replacing a Front Side Marker
Light Bulb
348
BULB
SOCKET SOCKET BULB
\f—\f—\f
y

\fy
() 
\fy\fy
2008 RDX

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.
Install the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
1.
2. 3.
4.
3.
4.
CONT INUED
Lights
Replacing Rear Bulbs
(in Tailgate)
Maint enance
349
COVER
NOTCH SOCKETS
BULBS
\f—\f—\f
y

y
() 
\fy\fy
2008 RDX

Determine which of the three
bulbs is burned out: brake/
taillight, turn signal or rear side
marker.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the tailgate.
Remove the two bolt covers on the
rear pillar by prying on the bottom
edge with a flat-tip screwdriver.
Remove the bolts with a Phillips-
head screwdriver, and remove the
light assembly f rom the rear pillar.
Turn on the lights to make sure
the new bulb is working.
Reinstall the light assembly cover.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
2. 4.
5.
3.
1.
5.
6.
7.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
350
COVERS
BULB SOCKET
BOLTS
\f—\f—\f
y

y
() 
\fy\fy
2008 RDX

CONT INUED
Use a Phillips-head screwdriver to
remove the screw and use a flat-
tipped screwdriver to remove the
holding clip located under the
f ront bumper.
Push up the undercover.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
1.
2.
6.
7.
8.
Lights
Replacing a Front Fog L ight Bulb
Maint enance
351
HOLDING CLIP
SCREWHalogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the
glass can cause the bulb to overheat
and shatter.
\f—\f—\f
y

y
() 
\fy\fy
2008 RDX

Remove the two screw covers on
the light assembly by prying on
the side edge with a flat-tip
screwdriver.
Remove the screws with a Phillips-
head screwdriver, then remove
the light assembly f rom the
tailgate.
Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Put the undercover in place.
Reinstall the clip, and tighten the
screw securely.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise. 5.
6.
7.
8.
1.
2.
3.
4.
Lights
Replacing a High-mount Brake
Light Bulb
352
COVERS
SCREWS
CONNECTOR
BULB
\f—\f—\f
y

\fy
() 
\fy\fy
2008 RDX

Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Press the brake pedal to make
sure the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Reinstall the high-mount brake
light assembly into the tailgate.
Tighten the two screws and
reinstall the covers.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise. 6.
5.
7.
3.
4.
Lights
Side T urn Signal L ight
Replacing a Rear License Plate
Light Bulb
Maint enance
353
SOCKET
BULB
\f—\f—\f
y


y
() 
\fy\fy
2008 RDX

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. This keeps the
f loor mat f rom sliding f orward and
possibly interf ering with the pedals.
If you remove the driver’s f loor mat,
make sure to re-anchor it when you
putitbackinyourvehicle.A non-Acura f loor mat may not f it
your vehicle properly. This could
prevent the proper operation of the
f olding rear seats and the passenger’s
seat weight sensors. We recommend
using genuine Acura f loor mats. Do
not put additional f loor mats on top
of the anchored mat.
Cleaning the Seat Belts Floor Mats
Cleaning the Seat Belts, Floor Mats
354
LOOP
FLOOR MAT ANCHORS
\f—\f—\f
y

\fy
() 
\fy\fy
2008 RDX

Your vehicle is equipped with a
intercooler on the engine to cool the
air f low f rom a turbo charger into
the engine. The intercooler f ins bend
easily. Do not push them with your
f inger.This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
A udio A ntenna, Intercooler, Dust and Pollen Filter
A udio A ntenna Intercooler
Dust and Pollen Filter
Maint enance
355
ANTENNA
INTERCOOLER
Your vehicle is equipped with an
antenna at the rear of the roof . Bef ore
using a ‘‘drive-through’’ car wash,
remove the antenna by unscrewing it by
hand. This prevents the antenna f rom
being damaged by the car wash brushes. Do not spray water (f rom such sources
as garden hoses, high pressure
sprayers) into the engine compartment.
It may cause serious damage to your
vehicle, and could also damage the
intercooler f ins.
\f—\f—\f
y

y
() 
\fy\f\fy
2008 RDX

To replace a f ront wiper blade: Disconnect the blade assemblyfrom the wiper arm:
Raise each wiper arm of f the
windshield, lif ting the driver’s side
first, then the passenger’s side.
Check the condition of the wiper
blades at least every six months.
Replace them if you f ind signs of
cracking in the rubber, areas that are
getting hard, or if they leave streaks
and unwiped areas when used.
Press and hold the lock tab.
Slide the blade assembly toward
the lock tab until it releases
from the wiper arm.
When replacing a wiper blade,
make sure not to drop the wiper
blade or wiper arm down on the
windshield.
2.
1.
Wiper Blades
356
WIPER ARMS
Do not open the hood when the wiper
arms are raised, or you will damage the
hood and the wiper arms.
\f—\f—\f
y

y
() 
\fy\f
y
2008 RDX