light Acura RL 2004 3.5 Owners Manual

µµµ µ
µ
µ
µ
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the page given.
Engine oil level Check every
time you fill the fuel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
you f ill the f uel tank. See page .
Windshield washer f luid Check
the level in the reservoir monthly.
If weather conditions cause you to
use the washers f requently, check
the reservoir each time you stop
f or f uel. See page .Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See
page . Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page
.
Automatic transmission Check
the f luid level monthly. See page .
Brakes Check the f luid level
monthly. See page . 207
208
263
264 266 281
286
Owner Maintenance Checks
Maint enance249

Install a new oil f ilter according to
instructions that come with it.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work. Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):
6.
7. 8.
9.
4.
5.
Engine Oil
Maint enance254
33 lbf·ft (44 N·m , 4.5 kgf·m)
4.9 US qt (4.6
)

Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,
when you use the washers of ten,
check the level every time you stop
for fuel.
The windshield washer reservoir is
located behind the driver’s side
headlight.
Check the reservoir’s f luid level by
removing the cap and looking at the
f loat. It should be up to the top of the
neck.Ifthefloatisatthebottomof
the neck, the reservoir is nearly
empty. When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.
Windshield Washers
Maint enance263
FLOAT
Do not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir.
Antif reeze can damage your car’s paint,
while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer f luid.

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently. 338
A ir Condit ioning Syst em
Maint enance277
AIR CONDITIONING CONDENSER
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

Check the operation of your car’s
exterior lights at least once a month.
A burned out bulb can create an
unsaf e condition by reducing your
car’s visibility and the ability to
signal your intentions to other
drivers.
Lights
Maint enance286
HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT
FRONT FOG LIGHT TURN SIGNAL/ PARKING LIGHTSIDE MARKER LIGHT

Check the f ollowing:Headlights (low and high beam)
Fog lights
Parking lights
Taillights
Brake lights
Turn signals
Back-up lights
Hazard light f unction
License plate lights
Side marker lights
High-mount brake light
Daytime running lights (Canadian
models)
If you f ind any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page to
determine what type of replacement
bulb is needed. 339
Lights
Maint enance287
HIGH-MOUNT BRAKE LIGHT
TURN SIGNAL LIGHT
LICENSE PLATE
LIGHTS BACK-UP LIGHT BRAKE/TAILLIGHTS

Halogen bulbs are used f or the high
beam headlight bulbs. When
replacing a high beam headlight bulb,
handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.Open the hood.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment of the
headlights should be perf ormed by
an Acura technician or other
qualif ied mechanic.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced. 1.
2.
3.
Lights
Maint enance
Headlight A iming
Replacing a High Beam Headlight
Bulb
288
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.

à
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb.
Insert the new bulb into the hole,
making sure the bulb is right side
up and the nubs on the bulb base
f it in the indentations in the
headlight assembly. Pivot the hold-
down wire back in place and clip
the end into the slot. Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘ .’’
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Your car uses halogen f og light
bulbs. See page f or inf ormation
on replacing a halogen bulb.
4.
5. 6.
7.
288
CONT INUED
Lights
Maint enance
ReplacingaFogLightBulb
289
WEATHER SEAL BULB
CONNECTOR HOLD-DOWN WIRE

à
Put the light assembly into the
bumper. Tighten the mounting
bolt. Push the electrical connector onto
the new bulb. Turn on the f ront
f og lights to test the new bulb. Install the rubber seal over the
back of the f og light assembly.
Make sure it is right side up; it is
marked ‘‘ .’’
Use a wrench to loosen the light
assembly’s mounting bolt.
Remove the light assembly f rom
the bumper.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back. Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way and remove the
bulb.Insert the new bulb into the hole,
making sure the bulb is right side
up and the nubs on the bulb base
f it in the indentations in the f og
light assembly. Pivot the hold-
down wire back in place and clip
the end into the slot.
1.
2.
3. 4.
5.6.
7.
8.
9.
Lights
Maint enance290
CONNECTOR
BOLT HOLD-DOWN WIRE
WEATHER SEAL
BULB

To remove the f ront turn signal/
parking light bulb, push it in
slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Install the new bulb into the
socket.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise. Pull the inner f ender cover back.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left. Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center. Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
1. 2.
3.
4.5.
6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
291
HOLDING CLIP