Acura RSX 2004 Repair Manual

Controls Near the Steering Wheel
Inst rument s and Cont rols58
WINDSHIELD
WIPERS/WASHERSHORN
TILT ADJUSTMENT
HEADLIGHTS/
TURN SIGNALS
MOONROOF REAR WINDOW DEFOGGER
CRUISE CONTROL
INSTRUMENT PANEL BRIGHTNESS
HAZARD WARNING BUTTON

µ
µ
µ µ
µ
µ
µ
µ µ
The wipers are not activated.
The wipers run at low speed.
The wipers run at high speed. Rotate clockwise to turn the rear
window wiper on.
Hold past ON to turn the window
wiper on and the window washer
to spray.
OFF
Rotate counterclockwise to turn
the window wiper on and the
window washer to spray.
The length of the wiper
interval is varied automatically
according to the vehicle’s speed.
Vary the delay by turning the INT
TIME ring. If you turn it to the
shortest delay, the wipers will
change to low speed operation
when the vehicle speed exceeds 12
mph (20 km/h).
Push the right lever up or down to
select a position. MIST
OFF
INT Intermittent
LO Low
HI High
Windshield Washers
The wipers run at high
speed until you release the lever. Pull the
wiper control lever toward you and
hold it. The washers spray until
you release the lever. The wipers
run at low speed, then complete
one more sweep af ter you release
the lever.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
OFF
LO
HI
Rear Window Wiper and Washer
INT
MIST Windshield Wiper Windshield Washer
Inst rument s and Cont rols
Wipers and Washers
59

µ
µ
µ
Turn Signal
Of f
Parking and interior lights
Headlight on
High beams
Flashhighbeams Rotating the
switch on the lef t lever turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate lights. Turning the
switch to the ‘‘ ’’ position turns
on the headlights. If you leave the
lights on with the key removed f rom
the ignition switch, you will hear a
reminder beeper when you open the
driver’s door.
To turn on the high
beams, push the lef t lever f orward
until it clicks. The blue high beam
indicator will come on (see page ).
Pull it back to return to low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back. With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignition
of f , even if you set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
Push down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The lever will return to center when you
release it or complete a turn.
1.
2.
3.
4.
5.
6. 52
Turn Signal and Headlights
Headlights On
High BeamsDaytime Running L ights
(Canadian Models)
Turn Signal
Turn Signal and Headlights
Inst rument s and Cont rols60

The knob on the instrument panel
controls the brightness of the
instrument panel. Turn the knob to
adjust the brightness.Pushtheredbuttontoturnonthe
hazard warning lights (f our-way
flashers). This causes all four
outside turn signals and both
indicators in the instrument panel to
f lash. Use the hazard warning lights
if you need to park in a dangerous
area near heavy traffic, or if your
vehicle is disabled.The rear window def ogger will clear
fog,frost,andthinicefromthe
window. Push the def ogger button to
turn it on and of f . The indicator in
the button comes on to show the
def ogger is on. If you do not turn it
of f , the def ogger will shut itself of f
af ter about 25 minutes. It also shuts
of f when you turn of f the ignition.
You have to turn it on again when
you restart the vehicle.
CONT INUED
Instrument Panel Brightness, Hazard Warning Button, Rear Window Def ogger
Rear Window Def ogger
Instrument Panel Brightness Hazard Warning Button
Inst rument s and Cont rols61

Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
Thedefoggerwiresontheinsideof
the rear window can be accidentally
damaged. When cleaning the glass,
always wipe side-to-side.Make any steering wheel adjustment
bef ore you start driving.
To adjust the steering wheel upward
or downward:Push the lever under the steering
column all the way down.
1.
See page f or important saf ety
inf ormation about how to properlyposition the steering wheel. 15
Rear Window Def ogger, Steering Wheel A djustment
Steering Wheel A djustment
Inst rument s and Cont rols62
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.

Move the steering wheel so it
points to your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.
Push the lever up to lock the
steering wheel in that position.
Make sure you have securely
locked the steering wheel in place
by trying to move it up and down.The master key fits all the locks on
your vehicle. The valet key works only in the
ignition and the door locks. You can
keepthegloveboxlockedwhenyou
leave your vehicle and the valet key
at a parking facility.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a key replaced. Use only
an Acura-approved key blank.
2.
3.
4.
CONT INUED
Steering Wheel A djustment, K eys and L ocks
Inst rument s and Cont rols
Keys and Locks
63
MASTER KEY
(BLACK)
VALET KEY
(GREY)
KEY
NUMBER
TAG

These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The keys do not contain batteries.
Do not try to take them apart. The Immobilizer System protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine’s f uel
system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.If the system repeatedly does not
recognize the coding of your key,
contact your Acura dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undriveable.
If you have lost your key and cannot
start your engine, contact your
Acura dealer.
Keys and Locks, Immobilizer System
Immobilizer System
Inst rument s and Cont rols64

µAs required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). You can insert or
remove the key only in this position.
To turn the key, the shift lever must
be in Park, and you must push the
key in slightly.
If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
CONT INUED
LOCK (0)
Ignition Switch
Inst rument s and Cont rols
Immobilizer System, Ignition Switch
65

µ
µ
µ Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom ACCESSORY
(I) to ON (II). ST A RT (III)
A CCESSORY (I)
ON (II)
Ignition Switch
Inst rument s and Cont rols66
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control.
Remove the key from the
ignition switch only when
parked.

Each door has a lock tab at the top of
the door. When you push down the
lock tab on the driver’s door, both
doors and the hatch lock. The lock
tabs on both doors lock and unlock
only that door. Pulling up on the
driver’s door lock tab only unlocks
the driver’s door.To lock both doors and the hatch,
press the master door lock switch on
either door, press the lock tab down
on the driver’s door, or use the key
on the outside lock.
Pulling up on either master door lock
switch will unlock both doors and the
hatch.
To unlock the driver’s door f rom the
outside, turn the key and release it.
If you turn and hold it, both doors
and the hatch unlock. Both doors
and the hatch unlock when you use
the key in the passenger’s door.
Door L ocks
Door L ocks
Power Door/Hatch L ocks
Inst rument s and Cont rols67
LOCK TAB MASTER DOOR AND HATCH
LOCK SWITCH