buttons Acura TL 2002 3.2 Owner's Manual

µTurn of f the engine.
Press and hold the select and reset
buttons on the instrument panel,
then turn the ignition switch ON
(II).
Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km) this
indicator will light f or two seconds
when you f irst turn the ignition
switch ON (II), and then f lash f or
ten seconds.
If you exceed 7,500 miles (12,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Acura dealer, reset the indicator as
f ollows.
For the f irst 6,000 miles (9,600 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch ON (II). This indicator reminds you that it is
time to take your car in for
scheduled maintenance.
Hold the buttons for
approximately ten seconds until
the indicator resets.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages .
1.
2.
3.
214 218
Gauges
Inst rument s and Cont rols
Maintenance Required Indicator
67
S SE
EL
LEE C
CT T B
BUUT TT
TO
ON N
R
RE ES
SE ET
T B
BUUT TT
TO
ON N
M
M
A
AI
INNT TE
EN
NA AN
NC CEE R
REEQ
QU UIIRRE ED
D
I
IN ND DI
ICCA A T
TO
OR R
00/12/25 14:04:52 31S0K630_070

To turn it back on, repeat this
procedure. The LED will come on
for one second to indicate the
f eature has been turned on. If the seat and mirrors are already in
the proper positions, you will hear
three beeps when you open the door.
The driving position memory
activated (Memory 1, Memory 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
You can turn of f this driving position
memory activation. Press and hold
the LOCK and UNLOCK buttons at
thesametime.TheLEDinthe
remote transmitter will blink twice.
Then release the buttons.
Theremotetransmitterswillalso
activate the Driving Position
Memory System (see page ).
When you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep.
The driver’s seat and outside mirrors
move to the positions stored in that
memory location. You will hear two
beeps when the movement is
complete.
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
96
Keys and Locks
Inst rument s and Cont rols
Recalling a Memorized Driving
Position
Panic Mode
82
W Wi
itth h M
M e
em
m o
or
ryy 1
1 W
Wiitth h M
M e
em
m o
or
ryy 2
2
00/12/25 14:07:28 31S0K630_085

Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Store a driving position as explained
in this section only when the car is
parked.
Your Acura has a memory f eature
f or the driver’s seat and outside
mirror positions.
Two seat and outside mirror
positions, f or dif f erent drivers or
drivingconditions,canbestoredin
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Memory1orMemory2).
Adjust the seat to a comfortable
position (see page ).
Adjust the outside mirrors f or best
visibility (see page ).Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
3.
1.
2.
88
94
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols96
M M E
EM
M O
O B
BUUT TT
TO
ON N
00/12/25 14:09:46 31S0K630_099

You can manually select the f an
speed by pressing any of the f an
control icons. This button controls the source of
the air going into the system. When
the indicator in this button is lit, air
from the car’s interior is sent
through the system again
(Recirculation mode). When the
indicator is of f , air is brought in f rom
outside the car (Fresh Air mode).
You can, f or example, manually put
the system in recirculation mode
when driving through an area of
smoke or f umes. When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set it below the
outside temperature. With the A/C
on, use the temperature buttons to
adjust the temperature of the air
flow to a comfortable setting.
CONT INUED
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures
Fan Cont rol Icons
Recirculat ion But t on
125
F FA
A N
N C
COON NTTR
RO OL L I
ICCO ON NSS
M
M
O
ODDE
E I
ICCO ON NSS
R
RE EC
CI IRRC CUUL LAA T
TI
IOON N B
BUUT TT
TO
ON N
00/12/25 14:13:59 31S0K630_128

Î
Î
Your Acura’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.The anti-thef t f eature will disable the
system if it is disconnected f rom the
car’s battery. To get the system
working again, you must enter a
code number (see page ).
The cassette system f eatures Dolby
noise reduction, automatic sensing of
chromium-dioxide (CrO ) tape, and
autoreverse f or continuous play.
The in-dash CD changer holds up to
six discs. You operate the CD
changer with the same controls used
f or the radio. See page f or CD
changer operation.
142
151
2
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Audio System
Comf ort and Convenience Feat ures
A M/FM/Cassette/CD Changer
Audio System
129
00/12/25 14:14:35 31S0K630_132

µµ
µ
µ ÓÓ
µ´
To store a f requency:Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each Preset
button.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s f requency is stored,
simply press and release the proper
preset button to tune to it.
The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. When the system is
in the SCAN mode, SCAN shows in
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band. The preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
You can use any of f our methods to
find radio stations on the selected
band: TUNE, SEEK, SCAN or the
Preset buttons.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Turn the knob right or lef t until the
display reaches the desired
f requency.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
either SEEK button ( or ), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward f rom the
current f requency. It stops when it
f inds a station with a strong signal. Use the TUNE or SEEK f unction
to tune the radio to a desired
station.
1.
2.
3.
4.
CONT INUED
Audio System
Comf ort and Convenience Feat ures
SCAN
Preset
TUNE
SEEK
131
00/12/25 14:14:56 31S0K630_134

µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations.
Audio System
Comf ort and Convenience Feat ures
AUTO SELECT
132
A A .
.S
SE EL
L B
BUUT TT
TO
ON N A
A
.
.S
SE EL
L I
INND DI
ICCA A T
TO
OR R
00/12/25 14:15:04 31S0K630_135

If you do not like the stations Auto
Select has stored, you can store
other f requencies in the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind the desired
f requencies, then store them in the
selected preset buttons as described
previously.
Auto Select does not erase the
f requencies that you preset pre-
viously. When you return home, turn
of f Auto Select by pressing the
A. SEL button. The preset buttons
will then select the f requencies you
originally set.
Audio System
Comf ort and Convenience Feat ures133
P PR
RE ES
SE ET
T B
BUUT TT
TO
ON NSS
S
SC
CAA N
N B
BUUT TT
TO
ON N
S
SEEE
EK
K B
BUUT TT
TO
ON NSS
A
A .
.SSE EL
L B
BUUT TT
TO
ON N A
A
.
.SSE EL
L I
INND DI
ICCA A T
TO
OR R
T
TU
UN NEE K
KNNO OBB
00/12/25 14:15:11 31S0K630_136

µÓ
Ó
ÓÓ
µ
´
µ´
The SKIP f unction allows
you to f ind the beginning of a song
or passage. To skip to the beginning
of a song or passage currently
playing, push the button. You will
see REW flashing in the display as
thetaperewinds.Toskiptothe
beginning of the next song, push the button. You will see FF f lashing in
the display as the tape fast forwards.
When the system f inds the begin-
ning of a song or passage, it goes
back to PLAY.
To stop the SKIP f unction bef ore it
f inds the beginning of a song or
passage, press either of the SKIP
buttons ( or ).
CONT INUED
SK IP
Audio System
Comf ort and Convenience Feat ures139
S SK KIIPP B
BUUT TT
TO
ON NSS
R
RP PT
T B
BUUT TT
TO
ON N R
RE
EP
PE
EA
A T
T I
INND DI
ICCA A T
TO
OR R
F
FF F B
BUUT TT
TO
ON N
R
RE EW
W B
BUUT TT
TO
ON N
00/12/25 14:16:11 31S0K630_142

µThe Repeat f unction
continuously replays the current
song or passage. Press the RPT
button to activate it; you will see RPT
displayed as a reminder. When the
system reaches the end of the song
or passage currently playing, it will
automatically go into rewind. When
it senses the beginning of the same
song or passage, the system returns
to PLAY mode. It will continue to
repeat this same program until you
deactivate REPEAT by pressing the
button again.
Pressing the REW or FF button, or
either of the SKIP buttons, also turns
of f REPEAT.
The SKIP and REPEAT f unctions
use silent periods on the tape to f ind
the end of a song or passage. These
f eatures may not work to your
satisfaction if there is almost no gap
between selections, a high noise
level between selections, or a silent
period in the middle of a selection.
REPEAT
Audio System
Comf ort and Convenience Feat ures140
R RE
EP
PE
EA
A T
T I
INND DI
ICCA A T
TO
OR R
R
RE EW
W B
BUUT TT
TO
ON N S
SK
KIIPP B
BUUT TT
TO
ON NSS
F
FF F B
BUUT TT
TO
ON N
R
RP
PT
T B
BUUT TT
TO
ON N
00/12/25 14:16:18 31S0K630_143