Acura TL 2003 3.2 Owner's Manual

µ
If you are training the second or
third buttons, go directly to Step 1. Unplug the garage door opener
motor f rom the house current.
Bef ore you can use HomeLink to
operate devices around your home, it
must ‘‘learn’’ the proper codes. For
example, to train HomeLink to open
and close the garage door:
If you just took
delivery of your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red light f lashes. Release
the buttons, then proceed to Step 1.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red light in HomeLink. Select the HomeLink button you
want to train.
Press the button on the remote
control and the button on
HomeLink at the same time. Hold
down both buttons.
2. 3.
4.
1.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures
T raining HomeL inkBef ore you begin
158

CONT INUED
Canadian Owners:
The remote control you are training
from may stop transmitting after two
seconds. This is not long enough f or
HomeLink to learn the code. Release
and press the button on the remote
control every two seconds until
HomeLink has learned the code.For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so they send and
receive the correct codes.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control.
Plug in the garage door opener
motor, then test the HomeLink
transceiver button by pushing it. It
should operate the garage door.
If the button does not work, repeat
this procedure to train it again. If it
still does not work, you may have a variable or rolling code garage
door opener. Test this by pressing
and holding the HomeLink
transceiver button you just trained.
If the red light blinks f or two
seconds,thenstayson,youhavea
rolling code garage door opener.
You may be able to verify this with
the manufacturer’s documentation.
Go to ‘‘Training With a Rolling
Code System.’’
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
5.
6.
8.
7. T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures159

µµ
Itmaybehelpfultohavesomeone
assist you with this procedure.
Find the ‘‘Training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. The
manufacturer’s documentation
may help. Press the Training button on the
garage door opener unit until the
light next to the button comes on,
then release it. The light may blink,
or come on and stay on. You then
have approximately 30 seconds to
complete the f ollowing steps.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Press and hold the button on
HomeLink f or 3 4 seconds.
(The same button you trained with
the ‘‘Training HomeLink’’
procedure.)
Press and hold the HomeLink
button again f or 3 4 seconds.
This should turn of f the training
light on the garage door opener
unit. (Some systems may require
youtopressthebuttonuptothree
times.)
Press the HomeLink button again.
It should operate the garage door.
6.
2. 4.
5.
1.
3.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures160
T TR
RA A I
INNI INNG G B
BUUT TT
TO
ON N

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red light
begins to f lash, then release the
buttons.
Youshoulderaseallthreecodes
bef ore selling the car.
Totrainanalreadyprogrammed
HomeLink button to operate a new
device:
Select the HomeLink button you
want to train.
Press and hold the HomeLink
button until the red light begins to
f lash slowly (approximately 20
seconds).
While continuing to hold the
HomeLink button, place the
remotecontrolforthedevice2to
5inchesfromHomeLink. Release both buttons. HomeLink
should now be trained to operate
the device.
Press and hold the button on the
remote control. Hold both buttons
until the red light begins to f lash
rapidly.
1.
2.
3.
4. 5.
Retraining a Button
Erasing Codes
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures161

The OnStarsystem in your vehicle
gives you access to a wide range of
services and information with the
touch of a button. An OnStar advisor
is available 24 hours a day, 7 days a
week. Press this button to contact an
OnStar advisor. You will hear a
chime, f ollowed by the
announcement, ‘‘Connecting to
OnStar.’’ The connection should take
20 to 30 seconds. The advisor will
assist you with any of the services
included in your plan.
Depending on what service you
request, you may need to give your
Personal Identification Number
(PIN) to the advisor. Your PIN is a
number you make up and provide
when you establish your OnStar
service.
If cellular telephone service is not
available in the area you are driving
in, you will hear a f ast busy signal.
The system will retry the connection
several times bef ore returning to the
ready mode.
The OnStar buttons and indicator
are located in the base of the rear
view mirror.
The Saf e and Sound Plan provides:
Roadside Assistance.
Emergency Services.
Automatic Notif ication of Airbag
Deployment.
Accident Assist.
Remote Door Locking/Unlocking.
Stolen Vehicle Tracking.
Misplaced Vehicle Assistance.
Online Concierge Services.
The Directions and Connections
Plan provides these additional
f eatures: Route Support.
Ride Assist.
Inf ormation and Convenience
Services.
The Luxury and Leisure Plan adds: Personal Concierge Services. OnStar Services Button
OnStar Control Panel
OnSt ar
Comf ort and Convenience Feat ures162
O On nS
St taar r B
BU UT TT
TO
ON N S
SY
YSSTTE
EM
M
S
ST TA
A T
TU
US S L
LIIGGH HT
T
E
E M
M E
ER
RG GE EN
NC CYY
B
BU UT TT
TO
ON N
C
CA
A L
LLL
A
A N
NS SWWE ER
R/ /E
E N
ND D
B
BU UT TT
TO
ON N

µµ
µ
µ
To cancel these retries, press the
Call Answer/End (DOT) button.
A microphone is located in the base
of therearviewmirrorsoyoucan
speak to the advisor without taking
your hands of f the steering wheel or
diverting your attention f rom the
road. The OnStar advisor’s voice
comes f rom the audio system’s
speakers. Use the volume control on
the audio system or on the steering
wheel to adjust the volume.
Press this button to contact an
OnStar advisor only if you have an
emergency situation. You will hear a
tone, f ollowed by the announcement,
‘‘Connecting to OnStar Emergency.’’
Your call is given highest priority. The advisor will ask about the nature
of the emergency, locate your
vehicle, and notif y the appropriate
emergency service agencies.
Press this ‘‘DOT’’ button to end a call
to the OnStar advisor, or to cancel
the call if you should press one of
the other buttons accidentally. If the
OnStar center should call you, press
this button to answer the call.
This button is also used to initiate
the Personal Calling and Virtual
Advisor services, if you have
subscribed.This light shows you the status of
the system.
The system is ready
for use.
Acallisin
progress.
There is a problem in
the system. Press the OnStar button
to contact an advisor. If the call
connects, the advisor will assist you
with verif ying the system’s operation.
If you are not able to contact an
advisor, take your vehicle to an
Acura dealer to have the system
diagnosed.
There is a problem
in the system with a call in progress.
If you press this button accidentally,
do not cancel the call. Wait until the
OnStar advisor answers, then explain
your mistake.
Emergency Button Call Answer/End ButtonSolid Green
Blinking Green
Solid Red
Blinking Red System Status L ight
OnSt ar
Comf ort and Convenience Feat ures163

µ
µ µ
µ µ
µ
The OnStar system uses the Global
Positioning System (GPS) to locate
your vehicle whenever you place a
call. This allows the advisor to
quickly contact the nearest services
without requiring you to provide
detailed directions.
Contact
the OnStar advisor if you need
assistance with a problem (f lat tire,
out of f uel, etc.) while traveling. The
advisor will contact an appropriate
agency to come and assist you.
Contact an
OnStar advisor if you have an
emergency situation. The advisor
will contact the nearest emergency
services provider (ambulance, f ire
department, etc.) and advise them of
your situation. If you are ever in an
accident that causes the airbags to
deploy, the OnStar system
automatically places a call (provided
the OnStar system and your vehicle’s
electrical system are still intact). The
advisor will attempt to speak to you
to evaluate the situation, and contact
the nearest emergency services
provider.
The OnStar
advisor can help you if you are ever
in a minor accident by asking you f or
inf ormation about the accident.
Complete, detailed inf ormation will
make it easier to complete accident
reports and insurance claims. By sending a signal to your
vehicle, the advisor can lock or
unlock your vehicle’s doors. This is
helpfulif youareawayfromyour
vehicle and realize you f orgot to lock
the doors, or if you have locked the
keys in your vehicle. To get OnStar’s
assistance, call (888) 4-ONSTAR
(466-7827).
Using
GPS, OnStar can locate your vehicle
almost anywhere. If your vehicle is
ever stolen, contact OnStar at (888)
4-ONSTAR. The advisor will put you
in contact with the proper authorities,
and assist them with locating your
vehicle.
Roadside Assistance
Emergency Services A utomatic Notif ication of A irbag
Deployment
A ccident A ssist
Saf e and Sound Plan Features
Remote Door L ocking/Unlocking
Stolen Vehicle T racking
OnSt ar
Comf ort and Convenience Feat ures164

µ
µ
µ
µµ
µ
The Luxury and Leisure plan
provides all the benef its of the other
plans, and adds:
An OnStar advisor can assist you
with purchasing theater tickets,
airline tickets, rental car reservations
for a vacation, and just about any
other purchase you desire.
The Directions and Connections
Plan provides these additional
f eatures.
If you are unable to locate your
vehicleinalargeparkinglotor
parking structure, contact OnStar at
(888) 4-ONSTAR. The advisor will
remotely activate the exterior lights
and the horn, allowing you to locate
your vehicle.
From your computer, you can log
into www. myonstar.com to make
dinner reservations, purchase tickets
to events, send f lowers, etc.
The OnStar advisor can
give you inf ormation on nearby
hotels, restaurants, ATMs, hospitals,
gas stations, and many other
services in any area you are traveling
in. The advisor can also help you
with hotel or restaurant reservations. If you need a ride
(taxi, limousine service, etc.) the
OnStar advisor can make the
arrangements f or you. Use the
OnStar button or call (888)
4-ONSTAR. The OnStar
advisor can give you verbal
directions f rom your current location
to a desired destination.
OnSt ar
Comf ort and Convenience Feat ures
Luxury and Leisure Plan
Features
Personal Concierge Services
Directions and Connections Plan
Features
Misplaced Vehicle Assistance
Online Concierge Services
Inf ormation and Convenience
Services Ride Assist Route Support
165

µOnStar will respond with ‘‘Dialing’’
andthenrepeatthecomplete
telephone number. It will then
place the telephone call.
The OnStar Personal Calling plan is
an extra-cost option that gives you
the ability to use your vehicle’s
OnStar system as a hands-f ree
cellular telephone.
To sign up f or Personal Calling,
press the OnStar button in your
vehicle, and notify the advisor that
you’d like to sign up. The advisor will
get all the information needed to set
up your account, and provide you
with your new cellular telephone
number.
You will need to provide a credit card
number, and prepurchase ‘‘units’’ or
minutes of air time (one unit equals
one minute). You
must use voice commands to give
the OnStar system your calling
inf ormation. To make a phone call:
Press the Call Answer/End
(DOT) Button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Dial.’’
OnStar will respond with ‘‘Number
Please.’’
Say the f irst digit of the number.
OnStar will repeat that digit.
Always wait f or OnStar to conf irm
the digit bef ore going to the next
digit.
Say the second digit of the number.
OnStar will repeat that digit.
Continue this until you have given
OnStar the complete telephone
number. Then say ‘‘Dial.’’ When you have f inished your
conversation, press the DOT
button again to hang up.
If you make a mistake speaking a
digit of the phone number, or the
system responds with the wrong
digit, say ‘‘Clear.’’ This will cause the
system to erase the last digit.
If you need to cancel the phone call
attempt bef ore entering the
complete phone number, say ‘‘Cancel.’’
The system will cancel the operation
and return to Ready.
If the system has difficulty
understanding a voice command, it
canrespondwith:
Comf ort and Convenience Feat ures
OnSt ar
Personal Calling Placing a Telephone Call
166

µ
µ
µ
µ µ
To store a
telephone number and its nametag in
the system:
Press the DOT button.
Say ‘‘Store.’’ OnStar will respond with ‘‘Ready.’’
OnStar will respond with ‘‘Number
Please.’’
Say the f irst digit of the number.
OnStar will repeat that digit.
Say the second digit of the number.
OnStar will repeat that digit.
Continue this until you have given
OnStar the complete telephone
number. Then say ‘‘Store’’ again.
OnStar will respond with
‘‘Nametag Please.’’
Say the name that you want
assigned to that telephone number.
Repeat the nametag. OnStar will respond with ‘‘Again.’’
OnStar will respond with ‘‘Once
more.’’
‘‘Pardon’’ The system could not
match your voice command to one it
knows. Repeat the command
distinctly.
‘‘Slower please’’ The system
missed the command because it was
not yet ready f or it, or there was too
much background noise. Repeat the
command after a short pause.
With
voice f eedback of f , the system will
respond with a tone rather than
‘‘Ready,’’ or repeating each number
you say. Other responses will still be
by voice. To turn voice f eedback on
or of f : When someone places a telephone
call to you, the audio system will
mute and you will hear the ring.
Press the DOT button to answer the
call. When you have completed the
call, press the DOT button again to
hang up.
The OnStar system can store up to
twenty 32-digit telephone numbers in
its memory. When you store these
numbers in its memory, you give
each one a nametag. When you want
to place a telephone call, you can
recall the number by giving the
system the nametag.
OnStar will respond with ‘‘Ready.’’ Press the DOT button.
Say ‘‘Voice Feedback.’’
OnStar will respond with ‘‘Voice
feedback On/Off.’’
CONT INUED
OnSt ar
Comf ort and Convenience Feat ures
Storing a Nametag
Voice Feedback On/Of f Incoming T elephone Calls
Using Nametags
167