display Acura TL 2004 Owner's Guide

µµ
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or a f ew
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. To store a channel:
Youcanstoreupto12
preset channel using the six preset
buttons or preset icons (models with
navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
To store a channel: Press the button. Either
XM1 or XM2 will show in the
display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected. Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Press the button again.
The other XM band will show.
Store the next six channels using
steps 2 and 3.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
1.
2. 3.
4.
5.
Playing t he XMSatellite Radio (U.S. Models)
Comf ort and Convenience Feat ures
SCAN
Preset
126

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the south side of an
east/west mountain road
Driving on the north side of a
large commercial truck on an
east/west road
Driving in the tunnels
Driving on a road beside a vertical
wall, steep clif f or hill to the south
of you
Driving on the lower level of a
multi-tiered road
Driving on a single lane road
alongside dense trees taller than
50 f t. (15 m) to the south of you
There may be other geographic
situations that could af f ect satellite
radio reception. If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the button.
A variety of music types and styles
will play.
If you decide to purchase XM
Satellite Radio service, contact XM
Radio at www.xmradio.com, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNEknob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
While awaiting activation, make sure
your vehicle remains in an open area
with good reception. Once your
audio system is activated, ‘‘category’’
or ‘‘CH’’ will appear in the display
andyou’llbeabletolistentoXM
Radio broadcasts. XM Radio will
continue to send an activation signal
to your vehicle for at least 12 hours
from activation request. If the
service has not been activated after
36 hours, contact XM Radio. After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
Playing t he XMSatellite Radio (U.S. Models)
Comf ort and Convenience Feat ures
Receiving Satellite Radio Service
128

Your Acura’s audio system has an in-
dash disc changer that holds up to
six discs. You operate this disc
changer with the same controls used
f or the radio. To operate the disc
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position.With the ignition in ACCESSORY
(I)orON(II),pressandholdthe
LOAD button until you hear a
beep and see ‘‘LOAD’’ in the
display, then release the button.
Insert the disc into the slot. Insert
it only about half way; the drive will
pull it in the rest of the way.
When the ‘‘DISC LOAD’’ appears
in the display, insert the next disc
into the slot.
Repeat this until all six positions
are loaded. The system will then
begin playing the last disc loaded.
The disc changer can play these disc
formats:
To load multiple discs in one
operation:
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 15 seconds, stop the load
operation, and begin playing the last
disc loaded.
To load a single disc:
Press and release the LOAD
button.
The disc number f or an empty
position is highlighted and the
green load indicator comes on.
When you see ‘‘LOAD’’ in the
display, insert the disc into the slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded.
CD
CD-R
DVD-A
DTS
DVD-A discs not meeting DVD
verification standards may not be
playable.
The changer cannot play DVD-V,
DVD-R/RW, MP3, or WMA f ormats.
Some CD-DA and CD-ROM mixed
discs are not playable.
DTS is registered trademark of
Digital Theater System, Inc. 1.
2.
3.
4.
1.
2.
Playing Discs
L oading Discs in the Changer
Comf ort and Convenience Feat ures130
TM
TM

µ´µ´
µ
Select the disc changer by pressing
the DISC/TAPE button (U.S.
models) or CD/DVD button
(Canadian models). The system will
begin playing the last selected disc in
the disc changer. You will see the
disc and track numbers displayed.
To select a dif f erent disc when all six
positions are loaded, use the preset 5
(DISC ) or preset 6 (DISC )
button. Otherwise, press the
corresponding number on the preset
buttons or icons. On models with
navigation system, you can also
touch the appropriate disc icon (1
6) to select a dif f erent disc. Each time you press and release the
SEEK button, the player skips
f orward to the beginning of the next
track. Press and release the SEEK
buttontoskipbackwardtothe
beginning of the current track.
When you press the SCAN button or
touchtheTRACKSCANicononthe
audio display (models with
navigation system), the f irst track of
the current disc plays f or about 10
seconds. You will see SCAN
(TRACK SCAN) highlighted in the
display. To hear the rest of the track,
press the SCAN button or touch
TRACK SCAN again within 10
seconds. If you don’t, the system
advances to the next track, plays
about 10 seconds of it, and continues
through the rest of the tracks the
same way.WhenyoupressandholdtheSCAN
button until you see D-Scan in the
display, or when you touch the DISC
SCAN icon on the audio display
(models with navigation system), the
f irst track of the current disc plays
f or about 10 seconds. You will see D-
Scan (DISC SCAN) in the display. To
hear the rest of the disc, press the
SCAN button or touch DISC SCAN
again, within 10 seconds. If you don’t,
the system advances to the next disc,
plays about 10 seconds of it, and
continues throughout the rest of the
discs the same way. When the
system reaches the last disc, DISC
SCAN is cancelled, and the disc you
originally had on plays normally.
CONT INUED
Playing Discs
Comf ort and Convenience Feat ures
To Play a Disc
To Change Tracks
Track Scan Disc Scan
131

To take the system out of disc mode,
press the AM/FM button (AM or
FMbuttononCanadianmodels),
press the button (U.S.
models), or insert a tape in the tape
player. To return to disc mode, press
the DISC/TAPE button (CD/DVD
buttononCanadianmodels).
If you turn the system of f while a
disc is playing, either with the PWR/
VOL knob or the ignition switch,
play will continue at the same point
when you turn it back on.
When you press the RPT button or
touch the TRACK RPT icon on the
audio display (models with
navigation system), the system
continuously replays the current
track. As a reminder, you will see
REPEAT (TRACK REPEAT) in the
display. To turn this feature off,
press the RPT button, or touch
TRACK REPEAT again.
WhenyoupressandholdtheRPT
button until REPEAT is in the
display, or when you touch the DISC
RPTiconontheaudiodisplay
(models with navigation system), the
system continuously replays the
current disc. As a reminder, D-RPT
(DISC RPT) is highlighted in the
display. To turn this feature off,
press the RPT button or touch DISC
RPT again. When you press the RDM button or
touch the TRACK RDM icon
(models with navigation system), the
system plays the tracks of the
current disc in random order. You
will see RANDOM (TRACK
RANDOM) in the display. To turn
this feature off, press the RDM
button (touch the TRACK RDM
icon) again.
You can also play DVD-As in your
audio system the same way as
playing discs.
Comf ort and Convenience Feat ures
Playing Discs
T rack Repeat
Random PlayT o Stop Playing a Disc
Disc Repeat Playing a DVD
132

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another disc in that position. If you
do not load another disc, within 15
seconds, the system selects the
previous mode [AM, FM1, FM2,
tape, or Satellite Radio (U.S.
models)].
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds and put the
disc changer in pause mode. To
begin playing the disc, press the disc
button.To remove a dif f erent disc f rom the
changer,firstselectitbypressing
the corresponding number on the
preset button (touching the
appropriate disc icon on models with
navigation system). When that disc
begins playing, press the eject button.
When you press the eject button
while listening to the radio, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the discs f rom the changer.
You can also eject discs when the
ignition switch is of f :
To eject one disc, press and release
the eject button.
To eject all discs, press and hold the
eject button until the system beeps.
Playing Discs
Removing Discs f rom the
Changer
Comf ort and Convenience Feat ures133

Message Cause
If you see an error message in the
display while playing a disc, f ind the
cause in the chart to the right. If you
cannot clear the error message, take
your vehicle to an Acura dealer. Solution
FOCUS Error.
No CD in the changer.
Mechanical Error.
High temperature.Press the disc eject button and remove the
disc(s). Check f or an error indication. Insert
the disc(s) again. If the code does not disappear
orthedisc(s)cannotberemoved,consultyour
Acura dealer.
Insert CD.
Press the disc eject button and remove the
disc(s). Check f or an error indication. Insert
the disc(s) again. If code does not disappear or
the disc(s) cannot be remove, consult your
Acura dealer.
Will disappear when the temperature returns to
normal.
Disc Changer Error Messages
Comf ort and Convenience Feat ures135

Ûµ
Î
Î
CONT INUED
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.
Thetapedirectionindicatorinthe
display comes on to show you which
side of the tape is playing. The
indicates the side you inserted
upward is now playing. If you want to
play the other side, press the PLAY/
PROG (preset2) button or touch the
PLAY/PROGiconontheaudio
display (models with navigation
system). When the player reaches
the end of the tape, it will
automatically reverse direction and
play the other side.
Dolby noise reduction turns on
when you insert a tape. Theindicator and NR icon (models with navigation system) will come on
in the display. If the tape was not
recorded in Dolby, turn it of f by
pressing the (preset 4) button
or touching the NR icon on the audio
display. Dolby remains of f until you
press the button (touch the icon)
again.
To remove the tape, press the
EJECT button. If you want to turn
the player of f , press the VOL/PWR
knob or turn of f the ignition. The
tape will remain in the drive. When
youturnthesystembackon,the
tape will begin playing where it lef t
off.
To switch to the radio, Satellite Radio (U.S. models) or disc changer
while a tape is playing, press the
AM/FM button (AM or FM button
on Canadian models), button
or DISC/TAPE button (CD/DVD
buttononCanadianmodels).To
change back to the tape player, press
the DISC/TAPE button (TAPE/
AUXbuttononCanadianmodels).
To rewind the tape,
push the (preset 1 ) button or
touch the REW icon on the audio
display (models with navigation
system). You will see REW in the
display (TAPE REW on models with
navigation system). To fast forward
the tape, push the (preset 3)
button or touch the FF icon. You will
seeFFdisplayed(TAPEFFon
models with navigation system).
Press the , , or PLAY/
PROG button (icon) to take the
system out of rewind or f ast f orward.
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Playing a T ape
Comf ort and Convenience Feat ures
To Play a Tape
To Stop Playing a TapeFF/REW T ape Search Function
137

µµ´
µ
Press the SEEK button
to f ind the beginning of the current
song or passage. Press the SEEK
button to f ind the beginning of the
next song or passage. When the
system reaches the beginning of a
song or passage, it begins to play it.
Press the RPT button
or touch the RPT icon on the audio
display (models with navigation
system) to continuously play a song
or passage. You will see RPT
displayed. The track will repeat until
you press the RPT button or icon
again. Thetapeplayerpicksupdirtand
oxides f rom the tape. This
contamination build up over time and
causes the sound quality to degrade.
To prevent this, you should clean the
player af ter every 30 hours of use.
If you do not clean the tape player
regularly, it may eventually become
impossible to remove the
contamination with a normal
cleaning kit. Your Acura dealer has a
cleaning kit available.
Use 100-minute or shorter tapes.
Tapes longer than that may break or
jam the drive.
If the tape is loose, tighten it by
turning the hub with a pencil or your
f inger. If the label is peeling of f ,
remove it or it could cause the tape
to jam in the player. Never try to
insert a warped or damaged tape in
the player.Store tapes in their cases to protect
them f rom dust and moisture. Never
place tapes where they will be
exposed to direct sunlight, high heat,
or high humidity. If a tape is exposed
to extreme heat or cold, let it reach a
moderate temperature bef ore
inserting it into the player.
Never try to insert f oreign objects
into the tape player.
The SKIP and REPEAT
f unctions use silent periods on the
tape to find the end of a song or
passage. These f eatures may not
work if there is almost no gap
between selections, a high noise
level, or a silent period in the middle
of a selection.
Playing a T ape
Comf ort and Convenience Feat ures
SK IP
REPEAT Caring f or the Player and Tapes
138
NOTE:

ÛÝ´
µ ´
µ
´ µ
Three controls f or the audio system
are mounted in the steering wheel
hub. These let you control basic
f unctions without removing your
hand f rom the wheel. The VOL button adjusts the volume
up ( ) or down ( ). Press the top
or bottom of the button and hold it
until the desired volume is reached,
then release it.
If you are listening to the radio, use
the CH button to change stations.
Each time you press the top ( ) of
the button, the system goes to the
next preset station on the band you
are listening to. Press the bottom
( ) to go back to the previous
station.If youareplayingaCD,thesystem
skips to the beginning of the next
track each time you press the top
( ) of the CH button. Press the
bottom ( ) to return to the
beginning of the current track. Press
it again to return to the previous
track. You will see the disc and track
numbers in the display.
If youareplayingatape,pressthe
top ( ) of the CH button to advance
to the next selection. Press the
bottom( )togobacktothe
previous selection. The system
senses a silent period, then goes
back to Play mode.
The MODE button changes the
mode. Pressing the button
repeatedly selects FM1, FM2, AM,
XM Satellite Radio (U.S. models),
CD (if a CD is loaded), or a tape (if a
tape is loaded).
Comf ort and Convenience Feat ures
Audio System
Remote Audio Controls
139
MODE BUTTON
VOL BUTTON CH BUTTON