Acura TL 2006 Owner's Manual

´´
µ
µ
Playing Discs
140
DISC
BUTTON LOAD
BUTTON
SEEK
BUTTONS
EJECT
BUTTON
SEEK
BUTTONS DISC
SLOT
DISC BUTTON
DISC BUTTON
RANDOM BUTTON
DISC BUTTON
RANDOM BUTTON REPEAT BUTTON
SCAN BUTTON DISC
SLOT
CD/DVD BUTTON
U.S. Models (with Navigation System)
Canadian Models (without Navigation System)
REPEAT
BUTTON SCAN
BUTTON LOAD
BUTTON DISC/TAPE
BUTTON AM/FM
BUTTON
PWR/VOL
KNOB PWR/VOL
KNOB
EJECT
BUTTON AM
BUTTON
FM
BUTTON

The disc changer can play these disc
formats:CD
CD-R
DVD-A
DTS
DVD-A discs not meeting DVD
verification standards may not be
playable.
The changer cannot play DVD-V,
DVD-R/RW, MP3, or WMA f ormats.
Some CD-DA and CD-ROM mixed
discs are not playable.
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater System, Inc. To load multiple discs in one
operation:
Your vehicle’s audio system has an
in-dash disc changer that holds up to
six discs. You operate this disc
changer with the same controls used
f or the radio. To operate the disc
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position.
With the ignition switch in the
ACCESSORY (I) or ON (II)
position, press and hold the LOAD
button until you hear a beep and
see ‘‘LOAD’’ in the display, then
release the button.
Insert a disc into the slot. Insert it
only about half way; the drive will
pull it in the rest of the way.
When the ‘‘DISC LOAD’’ appears
in the display, insert the next disc
into the slot.
Repeat this until all six positions
are loaded. The system will thenbegin playing the last disc loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 15 seconds, stop the load
operation, and begin playing the last
disc loaded.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. The disc number f or an empty
position is highlighted and the
green load indicator comes on.
When you see ‘‘LOAD’’ in the
display, insert the disc into the slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way. Press and release the LOAD
button.
To load a single disc:
1.
2.
3.
4. 1.
2.
L oading Discs in the Changer
Playing Discs
141
TM
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.

µ´µ´
µ
µ
´
Select the disc changer by pressing
the DISC/TAPE button (U.S.
models) or CD/DVD button
(Canadian models). The system will
begin playing the last selected disc in
the disc changer. You will see the
disc and track numbers displayed.
To select a dif f erent disc when all six
positions are loaded, use the preset 5
(DISC ) or preset 6 (DISC )
button. Otherwise, press the
corresponding number on the preset
buttons or icons. On models with
navigation system, you can also
touch the appropriate disc icon (1
6) to select a dif f erent disc.
WhenyoupressandholdtheSCAN
button until you see D-SCAN in the
display, or when you touch the DISC
SCAN icon on the audio display
(models with navigation system), the
f irst track of the current disc plays
f or about 10 seconds. You will see D-
SCAN (DISC SCAN) in the display.
To hear the rest of the disc, press
the SCAN button or touch DISC
SCAN again, within 10 seconds. If
you don’t, the system advances to
the next disc, plays about 10 seconds
of it, and continues throughout the
rest of the discs the same way.
When the system reaches the last
disc, DISC SCAN is cancelled, and
the disc you originally had on plays
normally.
Each time you press and release the
SEEK button, the player skips
f orward to the beginning of the next
track. Press and release the SEEK
buttontoskipbackwardtothe
beginning of the current track or to
skip back to previous track.
When you press the SCAN button or
touchtheTRACKSCANicononthe
audio display (models with
navigation system), the f irst track of
the current disc plays f or about 10
seconds. You will see SCAN
(TRACK SCAN) highlighted in the
display. To hear the rest of the track,
press the SCAN button or touch
TRACK SCAN again within 10
seconds. If you don’t, the system
advances to the next track, plays
about 10 seconds of it, and continues
through the rest of the tracks the
same way.
The preset 5 (DISC ) and preset 6
(DISC ) buttons are f or use with
an optional, external CD changer. T o Play a Disc
T o Change T racks Disc Scan
Track Scan
Playing Discs
Features
142

To take the system out of disc mode,
press the AM/FM button (AM or
FMbuttononCanadianmodels),
press the button (U.S.
models), or insert a tape in the tape
player. To return to disc mode, press
the DISC/TAPE button (CD/DVD
buttononCanadianmodels).
When you press the RPT button or
touch the TRACK RPT icon on the
audio display (models with
navigation system), the system
continuously replays the current
track. As a reminder, you will see
REPEAT (TRACK REPEAT) in the
display. To turn this feature off,
press the RPT button, or touch
TRACK REPEAT again.
If you turn the system off while a
disc is playing, either with the PWR/
VOL knob or by turning of f the
ignition switch, the disc will stay in
the drive. When you turn the system
back on, the disc will begin playing
where it lef t of f .
WhenyoupressandholdtheRPT
button until D-RPT is in the display,
or when you touch the DISC RPT
icon on the audio display (models
with navigation system), the system
continuously replays the current disc.
To turn this feature off, press the
RPT button or touch DISC RPT
again. You can also play DVD-As in your
audio system the same way as
playing discs. When you press the RDM button or
touch the TRACK RDM icon
(models with navigation system), the
system plays the tracks of the
current disc in random order. You
will see RDM (TRACK RANDOM)
in the display. To turn this f eature
off, press the RDM button (touch
the TRACK RDM icon) again.
T rack Repeat
Random PlayT o Stop Playing a Disc
Disc Repeat Playing a DVD
Playing Discs
143

To remove a different disc from the
changer,firstselectitbypressing
the corresponding number on the
preset button (touching the
appropriate disc icon on models with
navigation system). When that disc
begins playing, press the eject button.
When you press the eject button
while listening to the radio, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the discs f rom the changer.
You can also eject discs when the
ignition switch is of f :
To eject one disc, press and release
the eject button.
To eject all discs, press and hold the
eject button until the system beeps.
To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another disc in that position. If you
do not load another disc within 15
seconds, the system selects the
previous mode [AM, FM1, FM2,
tape,orXMRadio(U.S.models)].
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds and put the
disc changer in pause mode. To
begin playing the disc, press the disc
button. Removing Discs f rom the
Changer
Playing Discs
Features
144

When using CD-R discs, use only
high quality discs labeled f or audio
use.
When recording a CD-R, the
recording must be closed f or it to
be used by the disc changer.
Play only standard round discs.
Odd-shaped discs may jam in the
driveorcauseotherproblems.
Handle your discs properly to
prevent damage and skipping.When a disc is not being played,
store it in its case to protect it f rom
dust and other contamination. To
prevent warpage, keep discs out of
direct sunlight and extreme heat.
A new disc may be rough on the
inner and outer edges. The small
plastic pieces causing this roughness
can f lake of f and f all on the
recording surf ace of the disc,
causing skipping or other problems.
Remove these pieces by rubbing the
inner and outer edges with the side
of a pencil or pen.
Handle a disc by its edges; never
touch either surf ace. Do not place
stabilizer rings or labels on the disc.
These, along with contamination
f rom f inger prints, liquids, and f elt-
tip pens, can cause the disc to not
play properly, or possibly jam in the
drive.
Never try to insert f oreign objects in
the disc changer. To clean a disc, use a clean sof t cloth.
Wipe across the disc f rom the center
to the outside edge.
General Inf ormation
Protecting Discs
Protecting Your Discs
145

Message
If you see an error message in the
display while playing a disc, f ind the
cause in the chart to the right. If you
cannot clear the error message, take
your vehicle to your dealer. Cause
Solution
FOCUS error.
No CD in the changer.
Mechanical error.
High temperature. Press the disc eject button and remove the
disc(s). Check for an error indication. Insert
the disc(s) again. If the code does not disappear
orthedisc(s)cannotberemoved,consultyour
dealer.
Insert a disc or discs.
Press the disc eject button and remove the
disc(s). Check for an error indication. Insert
the disc(s) again. If the code does not disappear
or the disc(s) cannot be remove, consult your
dealer.
Will disappear when the temperature returns to
normal.
Disc Changer Error Messages
Features
146

Playing a T ape
147
DOLBY BUTTON
CD/DVD BUTTON
REWIND BUTTON
PLAY/PROGRAM BUTTON Canadian Models (without Navigation System)
U.S. Models (with Navigation System)
FAST FORWARD BUTTON FAST FORWARD BUTTON
DOLBY BUTTON SEEK
BUTTONS EJECT
BUTTON
REWIND BUTTON
PLAY/PROGRAM BUTTON REPEAT
BUTTON PWR/VOL
KNOB DISC/TAPE
BUTTON AM/FM
BUTTON PWR/VOL
KNOB FM
BUTTON
REPEAT
BUTTON
AM
BUTTON
EJECT
BUTTON
SEEK
BUTTONS
TAPE BUTTON

Ûµ
Î
Î
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Make sure the open side of
thetapeisfacingright,theninsert
thetapemostof thewayintotheslot.
Thesystemwillpullthetapeinthe
rest of the way and begin to play it.
Thetapedirectionindicatorinthe
display comes on to show you which
side of the tape is playing. The
indicates the side you inserted
upward is now playing. If you want to
play the other side, press the PLAY/
PROG (preset 2) button or touch the
PLAY/PROGiconontheaudio
display (models with navigation
system). When the player reaches
the end of the tape, it will
automatically reverse direction and
play the other side.
Dolby noise reduction turns on
when you insert a tape. Theindicator and NR icon (models with navigation system) will come on
in the display. If the tape was not
recorded in Dolby, turn it of f by
pressing the (preset 4) button
or touching the NR icon on the audio
display. Dolby remains of f until you
press the button (touch the icon)
again.
To remove the tape, press the
EJECT button. If you want to turn
the player of f , press the VOL/PWR
knob or turn of f the ignition. The
tape will remain in the drive. When
youturnthesystembackon,the
tape will begin playing where it lef t
off.
To switch to the radio, Satellite Radio (U.S. models) or disc changer
while a tape is playing, press the
AM/FM button (AM or FM button
on Canadian models), button
or DISC/TAPE button (CD/DVD
buttononCanadianmodels).To
change back to the tape player, press
the DISC/TAPE button (TAPE/
AUXbuttononCanadianmodels).
To rewind the tape,
push the (preset 1 ) button or
touch the REW icon on the audio
display (models with navigation
system). You will see REW in the
display (TAPE REW on models with
navigation system). To fast forward
the tape, push the (preset 3)
button or touch the FF icon. You will
seeFFdisplayed(TAPEFFon
models with navigation system).
Press the , , or PLAY/
PROG button (icon) to take the
system out of rewind or f ast f orward.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
To Play a Tape
To Stop Playing a TapeFF/REW T ape Search Function
Playing a T ape
Features
148

µµ´
µ
Press the SEEK button
to f ind the beginning of the current
song or passage. Press the SEEK
button to f ind the beginning of the
next song or passage. When the
system reaches the beginning of a
song or passage, it begins to play it.
Press the RPT button
or touch the RPT icon on the audio
display (models with navigation
system) to continuously play a song
or passage. You will see RPT
displayed. The track will repeat until
you press the RPT button or icon
again. Thetapeplayerpicksupdirtand
oxides f rom the tape. This
contamination build up over time and
causes the sound quality to degrade.
To prevent this, you should clean the
player af ter every 30 hours of use.
Use 100-minute or shorter tapes.
Tapes longer than that may break or
jam the drive.
If the tape is loose, tighten it by
turning the hub with a pencil or your
f inger. If the label is peeling of f ,
remove it or it could cause the tape
to jam in the player. Never try to
insert a warped or damaged tape in
the player.Store tapes in their cases to protect
them f rom dust and moisture. Never
place tapes where they will be
exposed to direct sunlight, high heat,
or high humidity. If a tape is exposed
to extreme heat or cold, let it reach a
moderate temperature bef ore
inserting it into the player.
Never try to insert f oreign objects
into the tape player.
The skip and repeat
f unctions use silent periods on the
tape to find the end of a song or
passage. These f eatures may not
work if there is almost no gap
between selections, a high noise
level, or a silent period in the middle
of a selection. If you do not clean the tape player
regularly, it may eventually become
impossible to remove the
contamination with a normal
cleaning kit. Your dealer has a
cleaning kit available.
SK IP
REPEAT
Caring f or the Player and Tapes
Playing a T ape
149
NOTE: