reset Acura TL 2010 Owner's Guide

Û
Ý ÛÝ
Memory Position Link
On models with keyless access system
When Memory Position Link is set
to ON, the driver’s seat and the
outside mirrors move to the
positions stored in memory. To
cause the memory to activate, open
the driver’s door with the remote
transmitter. On models with keyless
access system, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the memory positions, see
page .
For inf ormation on using the remote,
see page . You can choose this item to
customize f rom ‘‘POSITION
SETUP’’ by pressing the INFO ( /
) button repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
164
167
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109
09/07/29 17:00:53 31TK4610_114
2010 TL

Û
Ý
ÛÝ
ÛÝ
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘KEYLESS ACCESS SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode. KEYLESS ACCESS BEEP KEYLESS ACCESS
LIGHT FLASH DOOR UNLOCK MODE
There are three custom settings for
the keyless access setup:
CONT INUED
On models with keyless access system
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
111
: Press the INFO button ( / ).
: Press the SEL/RESET button. Seepage112
.
Seepage113 .
Seepage114 .
09/07/29 17:01:09 31TK4610_116
2010 TL

Û
Ý Û
Ý Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select DRIVER DOOR or ALL
DOORS by pressing the INFO ( /
) button, then enter your selection
by pressing the SEL/RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
UNLOCK MODE’’ and repeat the
procedure again.
Door Unlock Mode
Multi-Inf ormation Display
112
09/07/29 17:01:18 31TK4610_117
2010 TL

ÛÝ
Û
Ý Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /) button repeatedly.
The same exterior lights blink once
when you lock the doors by pushing
the door lock button while carrying
the remote.
Keyless Access Light Flash
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
113
09/07/29 17:01:28 31TK4610_118
2010 TL

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS BEEP’’ and
repeat the procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
115
09/07/29 17:01:44 31TK4610_120
2010 TL

Û
Ý
ÛÝ
ÛÝ
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. Here are the three custom settings
f or the lighting setup:
AUTO LIGHT SENSITIVITY
Lighting Setup
Multi-Inf ormation Display
116
: Press the SEL/RESET button. : Press the INFO button ( / ). See page
117.
See page 118.
See page 119.
09/07/29 17:01:53 31TK4610_121
2010 TL

Û
Ý ÛÝ
Interior Light Dimming Time
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘INTERIOR LIGHT DIMMING
TIME’’ and repeat the procedure
again.
The interior lights f ade out when you
close all doors. To change how long
thelightsstayonbeforetheyfade
out, f ollow these instructions:
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select the desired setting (15 sec, 30
sec, or 60 sec) by pressing the INFO
( / ) button, then enter your
selection by pressing the SEL/
RESET button.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
117
09/07/29 17:02:03 31TK4610_122
2010 TL

Û
Ý
ÛÝ
Headlight Auto Of f Timer
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /) button repeatedly. Press the SEL/RESET button to see
the selections.
The headlights, parking lights, side
marker lights, taillights, and license
plate lights go of f af ter the selected
time when you remove the key f rom
the ignition switch and close the
driver’s door. On models with
keyless access system, the lights go
of f af ter the selected time when you
close the driver’s door and take the
remote with you. To change how
longthelightsstayonbeforetheygo
of f , f ollow these instructions:
Select the desired setting (60 sec, 30
sec, 15 sec or 0 sec) by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
Multi-Inf ormation Display
118
09/07/29 17:02:11 31TK4610_123
2010 TL

ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
LIGHT SENSITIVITY’’ and repeat
the procedure again.
Press the SEL/RESET button to see
the selections.
Select the desired setting (MAX,
HIGH, MID, LOW or MIN) by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
120
09/07/29 17:02:30 31TK4610_125
2010 TL

Û
Ý
ÛÝ
ÛÝ
AUTO DOOR LOCK
Here are the five custom settings for
the door setup:
AUTO DOOR UNLOCK
While ‘‘DOOR/WINDOW SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. SECURITY RELOCK TIMER KEYLESS LOCK
ACKNOWLEDGMENT KEY AND REMOTE UNLOCK
MODE
CONT INUED
Door/Window Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
121
: Press the SEL/RESET button. : Press the INFO button ( / ). Seepage123
.
Seepage125 .
See page 126.
See page 127.
Seepage122
.
09/07/29 17:02:41 31TK4610_126
2010 TL