lights Acura TSX 2006 Owner's Guide

Page 274 of 366

̵
µµ
µ µ


U.S. Vehicles:
According to state and federal
regulations, f ailure to perf orm
maintenance on the items marked
with will not void your emissions
warranties. However, all
maintenance services should be
perf ormed at the recommended time
or mileage period to ensure long-
term reliability.
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the appropriate
page listed. Engine oil level Check every
time you f ill the f uel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
you f ill the f uel tank. See page .
Automatic transmission Check
the f luid level monthly. See pages
.
Brakes Check the f luid level
monthly. See page .
Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page .
Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
and license plate lights monthly.
Your authorized dealer knows your
vehicle best and can provide
competent, ef f icient service.
However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualif ied service f acility or
person who is skilled in this type of
automotive service. Keep all receipts
as proof of completion, and have the
person who does the work f ill out the
maintenance record. Check your
warranty booklet f or more
inf ormation.
We recommend the use of Acura
parts and f luids whenever you have
maintenance done. These are
manuf actured to the same high-
quality standards as the original
components, so you can be conf ident
of their perf ormance and durability. 232
232
285 286 288
303
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied’’ to EPA
standards.
Owner’s Maintenance Checks
Important Maintenance
Precautions
Maintenance Schedule
Maint enance
273
 — —y 
y
( y y

Page 292 of 366

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustments
should be perf ormed by your dealer
or other qualif ied mechanic.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs, one on each side. When
replacing a bulb, handle it by its steel
base and protect the glass from
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
CONT INUED
Headlight A iming
L ow Beam Headlight Bulb
Replacement
Replacing a High Beam Headlight
Bulb
Lights
Maint enance
291
NOTE:
Halogen headlight bulbs get
very hot when lit. Oil, perspiration, or a
scratch on the glass can cause the bulb
to overheat and shatter.
 — —y y
( y y

Page 293 of 366

Open the hood. To change a bulb
on the driver’s side, undo the
three fasteners and remove the air
intake cover.Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb
socket.
Pull the burned out bulb straight
out of its socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
headlight assembly. Make sure
the bulb is installed correctly by
looking through the headlight lens.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Install the rubber weather seal
over the back of the headlight
assembly.Makesureitisright
side up; it is marked with an arrow.
1.
2.
3.6. 4.
5.
7.
Lights
292
FASTENER
AIR INTAKE COVER
HOLD-DOWN WIREBULB
CONNECTOR
RUBBER WEATHER SEAL
SOCKET
 — —y y
( y y

Page 294 of 366

Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Turn on the headlights to test the
new bulb.
On the driver’s side, reinstall the
air intake cover. Reinstall the
three fasteners and secure them
by pushing on the heads until they
lock. Push the electrical connector onto
the socket. Make sure it is
connected securely.
3.
4.
5.
2. 1.
8.
9.
10.
Lights
Replacing the Turn Signal L ight
Bulb
Maint enance
293
SOCKET
BULB
 — —y y
( y y

Page 295 of 366

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, and turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
Lights
Replacing a Front Side Marker/
FrontParkingLightBulb
294
HOLDING CLIPS
 — —y y
( y y

Page 296 of 366

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.
Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket.Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Test the new bulb to make sure it
works.
Reinstall the light assembly cover.
1.
3. 2.
6.
7.
8.
4.
5.
6.
Lights
Replacing Rear Bulbs
(In Fenders)
Maint enance
295
COVER
 — —y  y
( y y

Page 297 of 366

Open the trunk.
Pull the lining back caref ully.Determine which of the two bulbs
is burned out: taillight or back-up
light.
To replace a bulb on the right side,
remove the trim clip. For the lef t
side, remove the two trim clips. Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to test the new
bulb.
Reinstall the trunk lid trim. Make
sure it is installed under the edge
of the trunk lid seal.
Press the trim clips back into their
holes.
1.
2. 5.
6. 4.
3. 7.
8.
9.
10.
Replacing Rear Bulbs
(in T runk L id)
Lights
296
TRIM CLIPS
SOCKETSBULBS
 — —y  y
( y y

Page 298 of 366

Open the trunk, and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
1.
2.
3.
CONT INUED
Lights
Replacing a High-mount Brake
Light Bulb Side T urn Signal L ight
Rear L icense Plate BulbReplacing a Front Fog L ight Bulb
Maint enance
297
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
 — —y y
( y   y

Page 299 of 366

Remove the undercover f ixing bolt
located under the f ront bumper.
Push up the undercover.Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the f og lights to test the
new bulb. Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Put the undercover in place.
Reinstall the f ixing bolt and
tighten it securely.
1.
2. 3.
4.5.
6.
7.
8.
Lights
298
UNDERCOVER FIXING BOLT
BULB
TAB
 — —y y
( y  
y

Page 314 of 366

CONT INUED
Park the vehicle on f irm, level and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area that is
far away from the traffic lanes.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.
2.
1.
Changing a Flat Tire
T aking Care of t he Unexpect ed
313
TRUNK FLOOR
JACK TOOL TRAY TOOLS
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.
 — —y y
( y 
y

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 next >