ignition Acura TSX 2007 User Guide

This shows how much fuel you
have. It may show slightly more
or less than the actual amount.
The needle returns to the
bottom after you turn off the
ignition.
This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise to
about the middle of the gauge. In
severe driving conditions, such as
very hot weather or a long period of
uphill driving, the pointer may rise to
the upper zone. If it reaches the red (Hot) mark, pull saf ely to the side of
the road. See page f or
instructions and precautions on
checking the engine’s cooling
system.
329
Gauges
Temperature Gauge Fuel Gauge
68
TACHOMETER
SPEEDOMETER
FUEL GAUGE
TEMPERATURE
GAUGE
U.S. Model is shown. INFO KNOB
SELECT/RESET KNOB
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

The multi -information display in the
instrument panel displays various
inform ation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comfortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs for continued trouble-free
driving.
When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome DRIVER 1’’ or ‘‘Welcome
DRIVER 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If
you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘DRIVER 1’’
or ‘‘DRIVER 2.’’ In this case, you
cannot use the customized settings
on the multi-information display (see
page ).
When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
There
are three types of messages;
normal display messages, engine oil
life and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi -information display and the
two buttons on the steering wheel
(see page ). 86
13286
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traffic, etc.
ELAPSED TIME: The time
trave led since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressu re is low on one or more
tires, inflate them to the correct
pressure. For more information,
see page .
The
primary display always shows its
default setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
IN FO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
258
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON

You can also change the display by
pushing the select/reset knob in the
instrument panel.
When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. While
a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In
the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
from ‘‘Trip A/Odome ter’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . 70
Multi-Inf ormation Display
Trip Meter
72
U.S.model is shown
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT

When the engine oil life reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code for the
maintenance items to be performed.
When the engine oil life reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items. Have
your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display after completing the service.
If you do not perform the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil life becomes 0 %. These
messages appear on the multi-
info rmation display each time you
turn the ignition switch to the ON
(II) position.
For more information about
Maintenance Messages, see
‘‘ ’’ on page
.
Also refer to page for important
maintenance saf ety precautions. 272
274
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown

If you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door, you will see
‘‘REMOVE KEY’’ on the display and
hear a reminder beeper. If
the brake fluid level is at or below
theMINmarkonthesideofthe
brake fluid reservoir in the engine
compartment, you will see ‘‘BRAKE
FLUID LOW.’’ If you see this
message, have the brake system
checked by your dealer (see page ). If thefuelfillcapismissingornot
tightened properly, you will see
‘‘TIGHTEN FUEL CAP.’’ Make sure
the fuel cap is installed and tightened
at least one click.
296
CONT INUED
Multi-Inf ormation Display
Remove Key Brake Fluid LowTighten Fuel Cap
Inst rument s and Cont rols
79
U.S.Canada

You can customize some vehicle
control settings for ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separate ly.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.
With
the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-info rmation
display.
If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,‘‘DRIVER
UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
Refertothetableonpage tosee
what settings you can customize. 88
Customized Settings
Multi-Inf ormation Display
86
DRIVER’S
ID

While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. Press the INFO button until
you see ‘‘PRIMARY DISP
SELECTION’’ as shown above.
When you turn the ignition switch to
the ON (II) position, the primary
display of the trip computer always
shows ‘‘INST. MPG’’ (U.S. models)
or ‘‘INST. L/100 km’’ (Canadian
models) in def ault setting. You can
customize this setting to your liking
in f ollowing procedure.
Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes f rom
‘‘INST. FUEL,’’ to ‘‘AVG. FUEL,’’ to
‘‘RANGE,’’ to ‘‘ELAPSED TIME,’’
then to ‘‘AVG. SPEED’’ each time
you press the INFO button. Enter
your selection by pressing the SEL/
RESET button.
Primary Disp Select ion
Multi-Inf ormation Display
102

The headlights, parking lights,
taillights, and license plate lights
turn of f af ter the selected time when
you remove the key f rom the ignition
switch and close the driver’s door.If you f ail to enter your selection,
you will see the above display f or
several seconds, then the display
goes back to ‘‘CUSTOMIZE MENU.’’
Repeat the setup.To exit ‘‘HEADLIGHT AUTO OFF
TIMER,’’ press the INFO button
until you see ‘‘EXIT,’’ then press the
SEL/RESET button. The display
goes back to ‘‘CUSTOMIZE MENU.’’
Multi-Inf ormation Display
Inst rument s and Cont rols
109

µµPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn. Turning the switch
on the lef t lever to the
‘‘ ’’position turns on the parking
lights, taillights, instrument panel
lights, side-marker lights, and rear
license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or the ‘‘ ’’ position, the
Lights On indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position.
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
Turn signal
Of f
Parking and indicator lights
Headlights
High beams
Flashhighbeams
Fog lights of f
Fog lights on
1.
2.
3.
4.
5.
6.
7.
8.
CONT INUED
Turn Signal
Headlights
Turn Signals and Headlights
Inst rument s and Cont rols
121