display Acura TSX 2008 Owner's Manual

If you have a f lat tire, the low tire
pressure/TPMS indicator and tire
monitor indicator will come on.
Replace the indicated f lat tire with
thecompactsparetire(seepage).
It is possible that the pressures
shown on the multi-inf ormation
display and the pressures you
manually measure are slightly
dif f erent.
If the dif f erence is signif icant or you
cannot make the low tire pressure/
TPMS indicator and message on the
multi-inf ormation display go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible.
After the flat tire is replaced with the
spare tire, the low tire pressure/
TPMS indicator stays on while
driving. Af ter several miles
(kilometers) driving, this indicator
begins to f lash, then stays on again.
You will also see a ‘‘CHECK TPMS
SYSTEM’’ message on the multi-
inf ormation display. This is normal;
the system cannot monitor the spare
tire pressure. Manually check the
sparetirepressuretobesureitis
correct.
This indicator and the warning
message on the multi-inf ormation
display will go of f , af ter several miles
(kilometers) driving, when the sparetire is replaced with the specified
regular tire equipped with the tire
pressure monitor sensor.
Each wheel is equipped with a tire
pressure sensor mounted inside the
tire behind the valve stem. You must
use TPMS specif ic wheels. It is
recommended that you always have
your tires serviced by your dealer or
a qualif ied technician.
Never use a puncture-repairing agent
in a f lat tire. If used, you will have to
replace the tire pressure sensor.
Havetheflattirerepairedbyyour
dealer as soon as possible.
324
Tire Pressure Monitoring System (TPMS)
Changing a T ire with T PMS
266
\f—\f—
y
y
(\fy\f
y
2008 TSX

If there is a problem with the TPMS,
you will see the above message on
the multi-information display.
If you see this message, the system
is of f and is not monitoring the tire
pressures. Have the system checked
by your dealer as soon as possible.
Also, the low tire pressure/TPMS
indicator begins to f lash, then stays
on (see page ).When you restart the vehicle with
thecompactsparetire,theTPMS
system message will also be
displayed on the multi-inf ormation
display af ter several miles
(kilometers) driving.
If you see this message, the tire
pressure monitor shows a ‘‘SYSTEM
FUNCTION ERROR’’ message. The
system may not be able to detect or
signal low tire pressure as intended.
Also, the tire pressure readings will
not be displayed. Have your vehiclechecked by a dealer as soon as
possible.
67
This device complies with Industry Canada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Changes or modif ications not expressly
approved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Tire Pressure Monitoring System (TPMS)
Check T PMS System Message
Driving
267
\f—\f—
y
y
(\fy\fy
2008 TSX

If the indicator does not come on
when the ignition switch is turned to
the ON (II) position, there may be a
problem with the VSA system. Have
your dealer inspect your vehicle as
soon as possible.
When the VSA system indicator
comes on, you will also see a
‘‘CHECK VSA SYSTEM’’ message
on the multi-information display.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
When VSA activates, you will see the
VSA activation indicator blink (see
page ).
If this indicator comes on while
driving, pull to the side of the road
when it is saf e, and turn of f the
engine. Reset the system by
restarting the engine. If the VSA
system indicator stays on or comes
back on while driving, have the VSA
system inspected by your dealer.
The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surf aces. It does this
by regulating the engine’s output and
by selectively applying the brakes.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. You will also see
the VSA activation indicator blink.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. 65
VSA A ctivation Indicator
Vehicle Stability Assist
(VSA ) System Indicator
Vehicle Stability Assist (VSA) System
268
\f—\f—
y
\fy
(\fy\fy
2008 TSX

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
This section also includes
instructions on how to read the
maintenance messages on the multi-
inf ormation display and instructions
for simple maintenance tasks you
may want to take care of yourself.
If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer.......................
Maintenance Saf ety .278
....................
Maintenance Minder .280
..............................
Fluid Locations .290
........................
Adding Engine Oil .291
Changing the Engine Oil and ...........................................
Filter .293
..............................
Engine Coolant .295
....................
Windshield Washers .296
.......................
Transmission Fluid .297
..........
Automatic Transmission .297
..............
Manual Transmission .299
................
Brake and Clutch Fluid .300
....................
Power Steering Fluid .301
.............................................
Lights .302
.......................................
Seat Belts .310
.....................................
Floor Mats .310
..................
DustandPollenFilter .311
.................................
Wiper Blades .312
...........................................
Wheels .314
...............................................
Tires .314
...................
Checking the Battery .320
.............................
Vehicle Storage .321
369
Maintenance
Maint enance
277
\f—\f—
y
\fy
(\fy\fy
2008 TSX

µ
µ
µ
µ
µ
µ
µ
µ
µ
µµ
µ
To see the current engine oil lif e
displayed on the lower segment of
the multi-information display, turn
the ignition switch to the ON (II)
position, and press the SEL/RESET
buttononthesteeringwheel
repeatedly until engine oil lif e is
displayed. The remaining engine oil lif e is
shownonthedisplayaccordingto
this table:
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%)
100% 90%
80%
70%
60%
50%
40%
30%
20%
15%
10% 5%
0%
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.
Based on the engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage.
Maintenance Minder
Engine Oil L if e Display
280
ENGINE OIL LIFE DISPLAY
REMAINING ENGINE OIL LIFE
\f—\f—
y
\fy
(\fy\fy
2008 TSX

CONT INUED
When the remaining engine oil lif e is
15 to 6 %, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance item code(s) indicating
themainandsubitemsrequiredat
thetimeof theoilchange.Referto
page f or a complete list of the
maintenance main items and sub
items.When the message appears, the
system message indicator also
comes on (see page ). Even after
you press the INFO button to cancel
the message, the indicator continues
to stay on until you have the service
perf ormed.
To cancel the message, press the
INFO button on the steering wheel.
Af ter the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see the
percentage of the remaining engine
oillifeandthemaintenanceitem
code(s) displayed.
75
289
Maintenance Minder
Maint enance
281
MAIN ITEM SUB ITEMS
MAINTENANCE ITEM CODE(S)
\f—\f—
y

\fy
(\fy\fy
2008 TSX

To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position. Af ter canceling the
message, the engine oil lif e display
will appear in the lower segment.
This continues until you have the
indicated maintenance done by your
dealer.When the remaining oil lif e is 5 to 1%,
the multi-information display shows
a ‘‘SERVICE DUE NOW’’ message.
The display also shows the same
maintenance items that were
previously shown with ‘‘SERVICE
DUE SOON.’’ Make sure you have
the indicated maintenance
perf ormed as soon as possible.To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
After have the service is performed,
make sure to reset the display as
described on page .
283
Maintenance Minder
282
\f—\f—
y


y
(\fy\fy
2008 TSX

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
CONT INUED
Maintenance Minder
Maint enance
283
‘‘SERVICE’’ MESSAGE
\f—\f—
y

y
(\fy\fy
2008 TSX

If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.To cancel resetting the oil life,
presstheINFObuttononthe
steering wheel to select
‘‘CANCEL’’ on the display, and
press the SEL/RESET button.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
Maintenance Minder
284
\f—\f—
y

y
(\fy\fy
2008 TSX

CONT INUED
Also, the percentage ‘‘0 %’’ keeps
blinking on the display.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.If the indicated required service is
not done and the remaining engine
oil lif e becomes 0 %, the multi-
inf ormation display will show a
‘‘SERVICE PAST DUE’’ message,
thetotalmileageaftertheremaining
oillifebecame0%,andthe
maintenance item code(s).
This particular message is displayed
when the mileage is less than 10
miles (f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage ‘‘0%’’ and the
maintenance item code(s) displayed.
Maintenance Minder
Maint enance
285
CANADA
U.S.
\f—\f—
y

y
(\fy\f\fy
2008 TSX