vin Acura TSX 2010 Service Manual

µµ When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote.
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
Press and hold this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in thememory that is activated by the
transmitter you normally carry.
Here are the settings activated with
the remote:
Customized settings
(see page ).
Driving position memory
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat moves
to the position stored in memory.
You will hear two beeps when the
movement is completed. The
indicator in the related memory
button on the driver’s door remains
on. 81
142
CONT INUED
All models except Canadian TSX with 4-cylinder engine
Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
Inst rument s and Cont rols
127
With Driver 2
With Driver 1
2010 TSX

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616 Separate the keypad from the
transmitter by pushing any button
f rom outside.Be caref ul when removing
this screw as the head of the screw
can strip out. Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
To replace the battery:
To turn the memory position link
settings back on, repeat this
procedure. The LED will blink once
to indicate the feature has been
turned on. You can turn of f this driving position
memory activation. Press and hold
the LOCK and UNLOCK buttons at
thesametime.TheLEDinthe
remote transmitter will blink twice.
Then release the buttons. Doing this
also cancels the memory position
link setting f or that remote and
restores the default settings. You will also see the ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
1.
2.
Remote Transmitter
Remote Transmitter Care
Replacing the Transmitter
Battery
128
NOTE:
KEYPAD
SCREW
2010 TSX

To close the trunk, use the inner
handle to lower the lid, then press
down on the back edge.
Keep the trunk lid closed at all times
while driving to avoid damaging it,
and to prevent exhaust gas from
getting into the interior. See,page . To protect items in the trunk, you
can disable the trunk release button
on the driver’s door and the trunk
release switch on the trunk lid by
turning of f the trunk main switch in
the glove box and locking the glove
box. Make sure either rear seat is
not f olded down.
If you need to give the key to
someone else, give them the valet
key. Even if the trunk release is locked
with the main switch, you can open
the trunk with the remote
transmitter.
Your vehicle is equipped with the
emergency f uel lid release in the
trunk. Refer to page for how to
access it.
55 474
Trunk
Carbon
Monoxide Hazard Trunk Main Switch
Emergency Fuel L id Release
Inst rument s and Cont rols
131
MAIN SWITCH
ONOFF
2010 TSX

µMoves the whole seat
up and f orward, or
down and backward.
Thefrontof theseat
also tilts up or down at
thesametime.
Moves the seat
f orward and backward.
Moves the f ront of the
seat up or down.
Raises or lowers the
seat. Adjusts the seat-back
angle f orward or
backward.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
The passenger seat has the same
adjustments as the driver’s seat but
without any height adjustment.
The driver’s seat includes a memory
f eature. Two seat positions can be
stored in separate memories. You
canthenselectamemorizedposition
by pushing the appropriate memory
button. Ref er to page f or how to
memorize and select the seat
positions.142
Driver’s seat only:
Driver’s seat only:
See pages f or important saf ety
inf ormation and warnings about how toproperly position the seats and seat-backs. 14
Driver’s seat only:
13
All models except Canadian TSX with4-cylinder engine
Seats
Power Seat A djustments
134
Driver’s seat is shown.
2010 TSX

See page f or important saf etyinf ormation and a warning aboutimproperly positioning head restraints. 14
CONT INUED
They are most ef f ective when you
adjust them so the center of the back
of the occupant’s head rests against
the center of the restraint.
Your vehicle is equipped with head
restraints in all seating positions to
help protect you and your
passengers f rom whiplash and other
injuries.
Vary the lumbar support by moving
theleveronthesideof theseat-back.
Move the lever forward or backward
to adjust the lumbar support through
its f ull range. Head Restraints
Driver’s L umbar Support
Seats
Inst rument s and Cont rols
135
2010 TSX

The head restraints adjust f or height.
You need both hands to adjust a
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button sideways, and push
the restraint down.To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the head restraint locks
in position when you reinstall it.
A djust ing t he Head Rest raint
Removing t he Head Rest raint
Seats
136
LEGSCUSHION
RELEASE
BUTTON
Front
CUSHION
Rear Center
SEAT-BACK SEAT-BACK
LEGS RELEASE
BUTTON
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
2010 TSX

The back of the rear seat folds down
to give you direct access to the trunk.
Each side f olds down separately.
With only half the seat f olded, you
can still carry a passenger in the
back seat. The seat-back can be
released f rom inside the trunk.When storing cargo, you can move
therearcentershoulderbeltoutof
the way by removing the belt from
the guide.To release the seat-back from inside
the trunk, pull the release under the
trunk panel. Push the seat-back
down f rom inside the trunk, or pull
the seat-back down f rom inside the
vehicle.
Seats
Folding the Rear Seats
138
CENTER SHOULDER BELTGUIDE
RELEASE
2010 TSX

Store a driving position only when
the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Adjust the seat to a comfortable
position (see page ). Press and release the SET button
on the control panel. You will hear
a beep. Immediately press and
hold one of the memory buttons (1
or 2) until you hear two beeps.
The indicator in the memory
button will come on. The current
position of the driver’s seat is now
stored.
Your vehicle has a memory feature
f or the driver’s seat position.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Driver 1 or Driver 2).
This setting can be linked or
unlinked with the remote transmitter.
To switch the link setting, see page
. 3.
1.
2.
134
93
All models except Canadian TSX with
4-cylinder engineStoring a Driving Position in
Memory
Driving Position Memory System
142
MEMORY BUTTONS
SET BUTTON
2010 TSX

The system will move the driver’s
seat to the memorized position. The
indicator in the selected memory
button will flash during movement.
When the adjustment is complete,
you will hear two beeps, and the
indicator will stay on.
Fail to press a memory button
within 5 seconds.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To select a memorized position, do
this:
To cancel the storing procedure
af ter pressing the SET button, do
any of the f ollowing:
Readjust the seat position.
Turn the ignition switch out from
the ON (II) position.
Make sure the parking brake is set
and the shif t lever is in Park
(automatic).If the parking brake is not set, you
must press and hold the memory
button until the adjustment is
complete.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
1.
2.
On vehicles with manual transmission
CONT INUED
Selecting a Memorized Position
Driving Position Memory System
Inst rument s and Cont rols
143
MEMORY BUTTONS
2010 TSX

To stop the system’s automatic
adjustment, do any of these actions:Press any button on the control
panel: SET, 1, or 2.
Push any of the adjustment
switches f or the seat.
Shif t out of Park (automatic).
Release the parking brake
(manual). If desired, you can use the
adjustment switches to change the
seat position af ter it is in its
memorized position. If you change
the memorized position, the
indicator in the memory button will
go out. To keep this seat position f or
later use, you must store it in the
driver’s seat position memory.
Driving Position Memory System
144
2010 TSX