engine Acura TSX 2011 Manual PDF

Jump Starting
284Handling the Unexpected
Jump Starting Procedure
Turn off the power to electric devices, such as audio and lights. Turn off the
engine, then open the hood.
Jump Starting
6-cylinder models 1. Slide out the battery terminal cover. All models 2. Connect the first jumper cable to your
vehicle's battery
terminal.
3. Connect the other end of the first jumper
cable to the assisting vehicle's
terminal.
Use a 12-volt booster battery only.
4. Connect the second jumper cable to the
assisting vehicle's
terminal.
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
4-cylinder models 6-cylinder models Booster Battery
Cover

285
Continued
Handling the Unexpected
Battery performance degrades in cold conditions
and may prevent the engine from starting. Jump Starting
5. Connect the other end of the second
jumper cable:
4 -cylinder models with automatic transmission

Engine mounting bolt
4 -cylinder models with manual transmission

Transmission mounting bolt
6-cylinder models

Engine hanger
Do not connect this jumper cable to any
other part of the engine.
6. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine
and increase its rpm slightly.
7. Attempt to start your vehicle's engine. If
it turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Jump Starting
6-cylinder models 4-cylinder models with
automatic transmission 4-cylinder models with
manual transmissionBooster Battery

286Handling the Unexpected
Jump Starting What to Do After the Engine Starts
Once your vehicle's engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
3. Disconnect the jumper cable from your vehicle's battery
terminal.
4. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
6-cylinder models

Overheating
288Handling the Unexpected
How to Handle OverheatingOverheating symptoms are as follows:
The temperature gauge needle is at the tH
mark or the engine suddenly loses
power.
Steam is coming out of the engine compartment. t
First thing to do
1. Immediately park the vehicle in a safe place. Automatic transmission models
Move the shift lever to P
and set the parking brake. Turn off all accessories
and turn on the hazard warning lights.
Manual transmission models
Move the shift lever to N
and set the parking brake. Turn off all accessories
and turn on the hazard warning lights.
2. No steam coming out: Keep the engine running and open the hood.
Steam coming out: Turn off the engine and wait until steam goes away.
Then, open the hood.
How to Handle Overheating NOTICE Continuing to drive with the temperature gauge
needle at the
H
mark may damage the engine.WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood or engine
compartment if steam is coming out.

Overheating
How to Handle Overheating
289
Handling the Unexpected
Last thing to do
Once the engine has cooled sufficiently, restart it and check the temperature
gauge.
If the temperature gauge needle has gone down, resume driving. If it has not
gone down, contact a dealer for repairs.
How to Handle Overheating
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure
only. Have a dealer flush the system with proper
antifreeze as soon as possible.
Next thing to do
1. Check that the cooling fan is operating
and stop the engine once the temperature
gauge needle comes down.
If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks. If the coolant level in the reserve tank
is low, add coolant until it reaches the
MA X mark. If there is no coolant in the reserve tank,
check that the radiator is cool. Cover
the radiator cap with a heavy cloth and
open the cap. If necessary, add coolant
up to the base of the filler neck, and put
the cap back on.
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to
spray out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve Tank
MAX
MIN

Indicator, Coming On/Blinking
290Handling the Unexpected
If the Low Oil Pressure Indicator Comes On
Reasons for the indicator to come on
Comes on when the engine oil pressure is low. What to do as soon as the indicator comes on
1. Immediately park the vehicle in a safe place.
2. If necessary, turn the hazard warning lights on. What to do after parking the vehicle
1. Stop the engine and let it sit for about one minute.
2. Open the hood and check the oil level.
Add oil as necessary.
3. Start the engine and check the low oil pressure indicator. The light goes out: Start driving again. The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
If the Charging System Indicator Comes On
Reasons for the indicator to come on
Comes on when the battery is not being charged. What to do when the indicator comes on
Turn the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
If the Low Oil Pressure Indicator Comes On NOTICE Running the engine with low oil pressure can cause
serious mechanical damage almost immediately. If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.

Indicator, Coming On/Blinking
If the Malfunction Indicator Lamp Comes On or Blinks
291
Handling the Unexpected
If the Malfunction Indicator Lamp Comes On or
Blinks
If the Malfunction Indicator Lamp Comes On or Blinks NOTICE If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could
be damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer
at 31 mph (50 km/h) or less. Have your vehicle
inspected.
Reasons for indicator lamp to come on or blink
Comes on when there is a problem with the engine emissions control t
system, or the fuel fill cap is missing, or loose.
Blinks when engine misfiring is detected. t What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at your
dealer. What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at
least ten minutes or more with the engine stopped until it cools.
Tighten Fuel Fill Cap Message The message appears on when:
An evaporative system leak is detected. This may be caused by the fuel fill cap
being loose or not being installed. What to do when the message appears:
1. Stop the engine.
2. Check that the fuel fill cap is fully installed.

If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
The message should go off.
When the malfunction indicator lamp comes on:
Malfunction indicator lamp comes on if the system continues to detect a leak
of gasoline vapor. If this happens, check the fuel fill cap using the procedures
described above.

Indicator, Coming On/Blinking
If the Brake System Indicator Comes On
292Handling the Unexpected
If the Brake System Indicator Comes On
Reasons for the indicator to come on
The brake fluid is low. t
There is a malfunction in the brake system. t What to do when the indicator comes on while driving
Press the brake pedal lightly to check pedal pressure.
If normal, check the brake fluid level the next time you stop. t
If abnormal, take immediate action. If necessary, downshift the t
transmission to slow the vehicle using engine braking.
If the Brake System Indicator Comes On
Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If
there is no resistance from the brake pedal, stop
immediately in a safe place. If necessary downshift
the gears.
If the brake system indicator and ABS indicator
come on simultaneously, the brake distribution
system is not working. This can result in vehicle
instability under sudden braking.
Have your vehicle inspected by a dealer immediately.
U.S.
CanadaIf the EPS Indicator Comes On
Reasons for the indicator to come on
Comes on when there is a problem with EPS. t
If you depress the accelerator pedal repeatedly to increase the t
engine speed while the engine is idling, the indicator comes on, and
sometimes the steering wheel becomes harder to operate. What to do when the indicator comes on
Stop the vehicle in a safe place and restart the engine.
If the indicator comes on and stays on, immediately have your vehicle
inspected by a dealer.
If the EPS Indicator Comes On NOTICE If you repeatedly turn the steering wheel at an
extremely low speed, or hold the steering wheel
on the full left or right position for a while, the
system heats up. The system goes into a protective
mode, and limits its performance. The steering
wheel becomes harder and harder to operate. Once
the system cools down, EPS is restored. Repeated
operation under these conditions can eventually
damage the system.

Fuses
294Handling the Unexpected
If any electrical devices are not working, turn the ignition switch to LOCK 0
and
check to see if any applicable fuse is blown.
Engine Compartment Fuse Box
Located near the brake fluid reservoir. Push the tabs to open the box.
Fuse Locations
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and
box cover number.
Circuit protected and fuse rating
Fuse Locations
Circuit Protected Amps
1Battery100 A
*1
120 A
*2
Passenger's Side Fuse Box 40A
2EPS 70 A
Passenger's Side Fuse Box (40 A)
ABS/ VSA FSR 30 A
−−
ABS/ VSA Motor 30 A
−−
Circuit Protected Amps
3IG 50 A
Driver's Side Fuse Box (40 A)
Passenger's Side Light Main 30 A
Driver's Side Fuse Box (60 A)
Driver's Side Light Main 30 A
Main Fan Motor 30 A
−
*1
−
Wiper Motor
*2
30 A
Wiper Motor
*1
Sub Fan Motor*2
30 A
4 Rear Defogger 40 A
5Sub Fan Motor
*1
20 A
−
*2
−
6− −
7− −
8 Heater Motor 40 A
9 Hazard 15 A
Circuit Protected Amps
10 H orn 10 A
11 − −
12 St o p 15 A
13 IG Coil 15 A
14 FI Sub 15 A
15 B a c ku p 10 A
16 Interior Lights 7.5 A
17 FI Main 15 A
18 DBW 15 A
19−
*1
−
Back Up FI ECU
*2
7. 5 A
20 MG Clutch 7.5 A
21Engine Oil Level
*1
7.5 A
Fan RLY
*2
*1: 4-cylinder models
*2: 6 -cylinder models

Fuses
Fuse Locations
295
Continued
Handling the Unexpected
Driver Side Fuse Box
Located under the dashboard.
Fuse Locations
Fuse locations are shown on the label on the side
panel.
Locate the fuse in question by the fuse number and
label number.
Circuit protected and fuse rating
Circuit Protected Amps
1− −
2 Seat Memory (7.5 A)
3 Washer 15 A
4 Wiper 10 A
5 Meter 7.5 A
6 ABS/ VSA 7.5 A
7ACG 15 A
8STS
*1
(7.5 A)
Star ter DIAG
*2
9 Fuel Pump 20 A
10 VB SOL* (10 A)
11 SRS 10 A
12 O D S 7. 5 A
Circuit Protected Amps
13−
*1
(7.5 A)
STS
*2
14 − −
15 Daytime Running Lights 7.5 A
16 A /C 7.5 A
17 Accessory, Key, Lock 7.5 A
18 Acces s or y 7.5 A
19 Driver's Power Seat Sliding (20 A)
20 Moonroof (20 A)
21 Driver's Power Seat Reclining (20 A)
22Rear Driver's Side Power
Window20 A
23Front Accessory Power
Socket20 A
24 Driver's Power Window 20 A
Circuit Protected Amps
25 Driver's Side Door Lock 15 A
26 Left Front Fog Light (10 A)
27Left Side Small Lights
(Exterior)10 A
28 Left Headlight High Beam 10 A
29 TPMS 10 A
30 Left Headlight Low Beam 15 A
31 − −
32 Engine Oil Level
*
(7.5 A)
*1: 4-cylinder models
*2: 6 -cylinder models
* Not available on all modelsFuse Label