lock Acura TSX 2011 Manual PDF

Replacing Light Bulbs
Front Turn Signal/Parking/Side Marker Light Bulbs
252Maintenance
Front Turn Signal/Parking/Side Marker Light BulbsWhen replacing, use the following bulbs.
Front Turn Signal/Parking/Side Marker: 21/5WTurn the steering wheel and pull the inner fender back in the same way as when
replacing the low beam headlights.
Changing the Low Beam Headlight

P. 2 5 0
1. Turn the socket to the left and remove it.
2. Push in the old bulb, rotate to the left until
it unlocks, and remove.
3. Insert a new bulb.2. Remove the coupler.
It can be removed by pushing the tab.
3. Rotate the old bulb to the left to remove.
4. Insert new bulb.
BulbSocket
Bulb
Ta b
Coupler

257
Checking and Maintaining Wiper Blades
Continued
Maintenance
Checking Wiper BladesIf the wiper blade rubber has deteriorated, it will leave streaks and the metal wiper
arm may scratch the window glass.Changing the Wiper Blade Rubber
1. Lift the driver side wiper arms first, then
the passenger side.
2. Place a cloth on the edge of the lock tab.
Push the lock tab up with a flat-tip screw
driver.
3. Slide the blade from the wiper arm.
Changing the Wiper Blade Rubber NOTICE Avoid dropping the wiper blade; it may damage the
windshield.
Lock Tab

Checking and Maintaining Wiper Blades
Changing the Wiper Blade Rubber
258Maintenance
4. Slide the wiper blade out from its holder
by pulling the tabbed end out.
5. Remove the retainer from the rubber blade
that has been removed, and mount to a
new rubber blade.
Correctly align the rubber protrusion
and the retainer groove.
6. Slide the new wiper blade onto the holder
from the bottom end. The tab on the blade should fit in the
indent of the wiper blade.
7. Slide the wiper blade onto the wiper arm,
then push down the lock tab.
8. Lower the passenger side wiper arm first,
then the driver side.
Blade
To p
Blade Retainer
Ta bIndent

Battery
268Maintenance
Checking the Battery
Check the battery condition monthly. Look
at the test indicator window and check the
terminals for corrosion.
If your vehicle's battery is disconnected or goes dead:
The audio system is disabled. t
Entering the audio security code

P.14 0
The clock resets. t
Setting the Clock

P. 8 8
The navigation system is disabled. A PIN code will be required. t
Refer to the navigation system manual

Charging the BatteryDisconnect both battery cables to prevent damaging your vehicle's electrical
system. Always disconnect the negative (-) cable first, and reconnect it last.
BatteryWARNING: Battery post, terminals, and
related accessories contain lead and lead
compounds.
Wash your hands after handling.The test indicator's color information is on the
battery.
When you find corrosion, clean the battery terminals
by applying a baking powder and water solution.
Rinse the terminals with water. Cloth/towel dry
the battery. Coat the terminals with grease to help
prevent future corrosion.
WARNING
The battery gives off explosive hydrogen
gas during normal operation.
A spark or flame can cause the battery
to explode with enough force to kill or
seriously hurt you.
Wear protective clothing and a face
shield, or have a skilled technician do any
battery maintenance.
Test Indicator Window

Cleaning
Interior Care
272Maintenance
Maintaining Genuine Leather
*
Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats
and seams. Clean the leather with a soft cloth dampened with a 90% water and
10% neutral soap solution. Then buff it with a clean, dry cloth. Remove any dust
or dirt on leather surfaces immediately.
Floor Mats
If you use any floor mats that were not originally
provided with your vehicle, make sure they are
designed for your specific vehicle, fit correctly, and
are securely anchored by the floor anchors.
Position the rear seat floor mats properly. If they
are not, the floor mat can interfere with the front
passenger seat's weight sensors.
Floor Mats
The front floor mats hook over the floor
anchors, which keep the mats from sliding
forward. To remove a mat for cleaning, turn
the anchor knobs to the unlock position.
When reinstalling the mat after cleaning, turn
the knobs to the lock position.
Do not put additional floor mats on top
of the anchored mats.
* Not available on all models
Driver's floor mat is shown.To unlock

Handling the Unexpected
This chapter explains how to handle unexpected troubles.
To o l s ..................................................... 276
Types of Tools .....................................276
If a Tire Goes Flat ................................ 277
Changing a Flat Tire ........................... 277
Engine Does Not Start
Checking the Engine .......................... 283
Jump Starting ..................................... 284
Shift Lever Does Not Move ............... 287
Overheating ........................................ 288
How to Handle Overheating .............. 288Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator
Comes On ........................................ 290
If the Charging System Indicator
Comes On ........................................ 290
If the Malfunction Indicator Lamp
Comes On or Blinks .......................... 291
If the Brake System Indicator
Comes On ........................................ 292
If the EPS Indicator Comes On ........... 292
If the Low Tire Pressure/ TPMS Indicator
Comes On or Blinks .......................... 293Fuses
Fuse Locations ................................... 294
Inspecting and Changing Fuses .......... 297
Emergency Towing ............................. 298
When You Cannot Unlock the Fuel
Fill Door ............................................. 299
When You Cannot Open the
Trunk .................................................. 300
275

277
If a Tire Goes Flat
Continued
Handling the Unexpected
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually
to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact
spare tire. Go to a dealer as soon as possible to have the full size tire repaired or
replaced.
1. Park the vehicle on firm, level, and non-slippery ground. Automatic transmission models 2. Put the shift lever in P
.
Manual transmission models 2. Put the shift lever in R
.
All models 3. Set the parking brake.
4. Turn on the hazard warning lights and turn the ignition switch to LOCK 0
.
Changing a Flat Tire
Periodically check the tire pressure of the compact
spare. It should be set to the specified pressure.
Specified Pressure: 60 psi (420 kPa, 4.2 kgf/cm
2)
When driving with the compact spare tire, keep
the vehicle speed under 50 mph (80 km/h). Replace
with a full size tire as soon as possible.
The compact spare tire and wheel in your vehicle
are specifically for this model.
Do not use them with another vehicle.
Do not use another type of compact spare tire or
wheel with your vehicle.
Do not mount tire chains on a compact spare tire.
If a chain-mounted front tire goes flat, remove one
of the full-size rear tires and replace it with the
compact spare tire. Remove the flat front tire and
replace it will the full size tire that was removed
from the rear. Mount the tire chains on the front
tire.
Do not use a puncture-repairing agent on a flat tire,
as it can damage the tire pressure sensor.
Changing a Flat Tire

If a Tire Goes Flat
Changing a Flat Tire
278Handling the Unexpected
2. Take the tool case out of the trunk. Take
the jack and wheel nut wrench out of the
tool case.
3. Unscrew the wing bolt, and remove the
spacer cone. Then, remove the spare tire. 1. Pull the handle on the trunk floor lid and
open the lid. Hook the handle to the edge
of the trunk opening.
Getting Ready to Replace the Flat Tire
4. Place a wheel block or rock in front and
rear of the wheel diagonal to the flat tire.
The tire to be replaced.
Wheel
Blocks
Tool Case
Spare Tire

If a Tire Goes Flat
Changing a Flat Tire
280Handling the Unexpected
WARNING
The vehicle can easily roll off the jack,
seriously injuring anyone underneath.
Follow the directions for changing a tire
exactly, and never get under the vehicle
when it is supported only by the jack.
How to Set Up the Jack
How to Set Up the Jack
Do not use the jack with people or luggage in the
vehicle.
Use the jack provided in your vehicle.
Other jacks may not support the weight
("load") or
their shape may not match.
The following instructions must be followed to use
the jack safely.
Do not use while the engine is running. tUse only where the ground is firm and level. tUse only at the jacking points. tDo not get in the vehicle while using the jack. tDo not put anything on top of or underneath the tjack.
1. Place the jack under the jacking point
closest to the tire to be changed.
2. Turn the end bracket (as shown in the
image) clockwise until the top of the jack
contacts the jacking point.
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the extension bar
and the jack handle, until the tire is off the
ground.
Extension Bar
Wheel Nut
Wrench as Jack
Handle

287
Shift Lever Does Not Move
Handling the Unexpected
Automatic transmission models Follow the procedure below if you cannot move the shift lever out of P
position.
1. Set the parking brake.
2. Remove the key from the ignition switch.
3. Wrap a cloth around the tip of a small flat-
tip screwdriver and remove the cover of
the shift lock release slot.
Put the tip of the flat-tip screwdriver
into the slot and remove it as shown in
the image.
4. Insert the key into the shift lock release
slot.
5. While pushing on the key, press the shift
lever release button and place the shift
lever into N
.
The lock is now released. Have the shift
lever checked by a dealer as soon as
possible.
Releasing the Lock
Cover
Slot
Release Button
Shift Lock Release Slot