can AUDI A3 2010 8P / 2.G RNS_E Navigation System Manual

Navigation (NAV)133
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP terminate this route guidance, select Cancel route guidance
page 132Tips
Calculated destinations can also be changed in the map display by
moving the crosshairs
page 149.
To p d e s t i n a t i o nFig. 138 Navigation: Set entry as top destinationFig. 139 Navigation: Map display of a top destination (push pin)
– In a destination input menu
page 117, fig.121, select
the top destination desired from the list below the menu
item “Start route guidance”.
– Select Start route guidance.If you have activated the Display as top destination
fig.138 func-
tion when making entries in the directory (
page 135 or
page 103), they are listed
page 136 in a destination input menu
page 117, fig.121 under the menu item “Start route guidance” .
If you have activated the top destinations
page 155in the “Map
content” menu with a checkmark
, the top destinations you set are
indicated by a “push pin” on the map
fig.139.

Navigation (NAV) 134Memory control buttonPrevious destinations
The previous destinations are stored and can be
loaded directly as a navigation destination.Fig. 140 Navigation: select previous destinations–Press the Memory c o n t r o l b ut t o n i n t h e n a v i g a t i o n m e n u .
– Select Previous destinations. You will see a list of the
most recently entered destinations. This list is updated
automatically.
– Select your desired entry.
– Select Start route guidance.Tips


There may be entries which cannot be displayed fully in the
display because they contain too many letters and are too long. If
you select one of these entries using the control knob, a second
window will open up after a few seconds. You will be given addi-
tional information about the selected entry in this window.


The list of previous destinations can be deleted in the Setup
Navigation menu
page 156.
To p c a t e g o r i e sFig. 141 Navigation: Top categories–Press the Memory control button in the navigation menu.

Navigation (NAV)135
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
–Select Top categories
page 134, fig.140. You are given
a list of suggestions with categories for useful special
destinations.
– Select the desired category (e.g. Gas station. You are
provided with a list containing the special destinations
from the selected category.
– Select a destination from the list.
–Select Set as destination. Die Zieldaten werden automa-
tisch in das Zieleingabemenü übernommen.
–Select Start route guidance.The special destinations are sorted according to distance from your
present location.
The following top categories are available:

Parking lot


Parking garage


Gas station


Audi service


HospitalTips
If no top special destination is found for the category selected, there
is no top special destination from this category in your vicinity or no
top special destination from this category exists on the navigation
DVD.
Store in directory
The current destination can be stored in the directory.Fig. 142 Navigation: Save current destination to directory– Enter a single destination
page 119.
–Press the Memory control button.
– Select Store in directory.
– Select New directory entry and complete the directory
card, or
– Select Find entry, to file the destination under an existing
directory card.

Navigation (NAV) 136
– I f y o u w a n t t h e a d d r e s s t o a p p e a r i n t h e To p D e s t i n a t i o n s
list
page 133 in einem Zieleingabemenü, select
Display as top destination
page 133, fig.138 and press
the control knob. A check

appears after the option.
– Select Save entry.
Using Store in directory you can assign an entry in your directory to
a destination
page 119.
A Name must first be entered in the directory data fields. After the
name has been entered, the remaining data fields can be selected.
I f yo u wa n t t o as s i g n a d e s t i n a t i o n to a n e n t r y a l re a d y s to re d in y o ur
directory, you must first enter the destination. Then select the entry
to be assigned using Store in directory and save it. The destination
entered is assigned to this entry. If you already have a destination
assigned to an directory entry, the new destination will overwrite
the old destination.
Addresses saved as top destinations are displayed in the destina-
tion input menu and can be selected there
page 133.
Tips


R o u t e p l a n s (ro u t e w it h s t o p o v e r s ) c a n b e s t o re d u s i n g t h e Store
route function
page 137.


Administration of the directory data is handled through the
button
page 98.
Load from directoryFig. 143 Navigation: Load from directory–Press the Memory control button in the navigation menu.
– Select Load from directory
page 134, fig.140.
– Select your desired destination from the list, or
– Select Find entry
fig.143.
– Enter the name you are looking for using the speller or
select one from the list.
– Select Start route guidance.You can also edit an existing address. The current address will then
be replaced.
NAME

Navigation (NAV)137
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
Administration of the directory data is handled through the
button
page 98.
Save route
Once calculated, route plans can be saved with the
route criteria you entered and loaded later as a new
destination.Fig. 144 Navigation: Route plan– Enter a route plan
fig.144.
–Press the Memory co n t ro l bu t to n i n t h e n a vi g a t i o n m e n u .
–Select Save route.– Using the speller, enter the name for the route.
– Select OK in the speller. The route plan entered is saved.
A route plan provides the option of setting up to three stopovers in
addition to a destination
page 121. You can then drive to each of
these destinations in turn in the sequence set up.
The route entered will be saved with the final destination and stop-
overs and can be loaded again as a new destination
page 137.
The route plan can be changed at any time after input is complete.
Select a destination from the route plan by rotating and pressing
the control knob. Then you can select Change, Move, Delete o r Drive
to now
page 137.
If you have selected the Drive to now function and you would not
l i k e t o e d i t t h e r o u t e , r o u t e g u i d a n c e i s i m p o r t e d a n d c u r r e n t v e h i c l e
location is used as the route guidance starting point after you have
selected Start route guidance.
If the Save route f u n c t i o n i s g r e y e d o u t , t h i s i n d i c a t e s t h a t e i t h e r t h e
route memory is full or the Route without stopover function (single
destination mode) is set. Please delete routes not needed from the
route memory
page 138. Or select the Route with stopover func-
tion
page 139Tips
You can save individual destinations to the directory
page 135.
Load route–Press the Memory c o n t r o l b ut to n i n t h e n a v i g a t i o n m e n u .
NAME

Navigation (NAV) 138
– Select Load route
page 134, fig.140.
– Select the route that you would like to load from the list.
– Select Start route guidance.After storing several route plans
page 137, they can be loaded
with a few operating steps.
A route plan can be changed at any time. Select a destination from
the route plan by rotating and pressing the control knob. Then you
can select Change, Move, Delete or Drive to now.
Change
Here you are entering new navigation data for your destination or
stopover.
Move
Here you are reordering the sequence of your destination and stop-
overs.
Delete
The selected destination or stopover can be deleted. If you delete a
destination, the system will automatically select a stopover and
make that your new destination.
Drive to now
You can drive directly to the selected final destination or stopover.
If you do not want to ed it the saved route, the route will b e sa ved in
the memory when Start route guidance is activated and the current
vehicle location will be used as the starting point for navigation.
Tips
A function may not be selected (“greyed-out”) if it is not available
according to the restrictions you have set, or if not permitted by
local circumstances.Delete route–Press the Memory control button in the navigation menu.
– Select Delete route.
– Select the route to be deleted from the list.
–Confirm Are you sure you want to delete the route? with
Ye s. The selected route is deleted.

Navigation (NAV) 140stopover, your route guidance will proceed with stopovers until you
select and confirm Route without stopover.
Route with stopover
Select this option to be guided to your final destination with stop-
overs.
Stopovers can also be special destinations
page 126.
Stopovers already entered can be deleted, changed or moved at any
time, or you can drive to them immediately page 137.
Route without stopover
Select this option to navigate directly to your destination.
Tips
If you switch to the Navigation function and you are shown the
menu for Route planning
page 139, fig .1 4 6 , y o u a r e in r o ut e g u id -
ance with stopovers. If you would like to navigate directly to a final
destination, select and confirm Route without stopovers in the menu
for the Route function.
Route listFig. 147 Navigation: Route list–Press the Route control button in the navigation menu.
– Select Route list
page 139, fig.145 . The detai led route
list appears
fig.147.The route list provides you with the following information:

Notes on the route


Distance information


Street designations


City namesTips
If route guidance is not activated, Route list will be greyed-out.

Navigation (NAV)141
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Route criteria
Route calculation depends on the route criteria
selected.Fig. 148 Navigation: Listing of the possible route criteria–Press the Route control button in the navigation menu.
–Select Route criteria.
– Select the desired route criteria
fig.148.The route criteria can be changed during route guidance and the
route can be recalculated.
You have the following route criteria available to you:
Route options
Using the options fast or short, an especially fast or short route is
taken as the basis for calculating the route.Highway
Comprises the options include and minimize. With Highway
minimize, an attempt is made to avoid sections of freeway when
calculating the route. If the destination is more than 300 km away,
freeways are not avoided.
Ferry
Comprises the options include and minimize. With Ferry minimize
a n a t t e mp t i s m a d e n o t to i n c l u d e a ny s t re t ch w hi ch i n c l ud e s a fe rr y
connection when calculating the route.
To l l r o a d
Comprises the options include and minimize. With To l l r o a d
minimize an attempt is made when calculating the route not to
include any stretch which includes a road which you have to pay to
drive on.
Time restrict.
Comprises the options include and minimize. With roads closed at
certain times of day avoid a n a t t e m p t i s m a d e t o e x c l u d e t h e s e r o a d s
when planning the route. But only the roads closed at certain times
of day identified on the Navigation DVD can be avoided.
Season restrict.
Comprises the options include and minimize. With seasonally
closed roads avoid a n a t t e m p t i s ma d e to e x c l u d e t h e s e ro a d s w h e n
planning the route. But only the seasonally closed roads identified
on the Navigation DVD can be avoided.
Tips
If you would like to avoid a route criterion, but this makes route
guidance impossible, this criterion is still included when calculating
the route. In this case, a voice message will inform you of this.

Navigation (NAV) 142Av o id ro u t eYou can select this function once calculated route guidance
is active.
–Press the Route control button in the navigation menu.
– Select Avoid route from here
page 139, fig.145.
– By rotating and pressing the control knob, select the
section on the presently calculated route from the
vehicle position.
– By pressing the control knob, you confirm the section
you wish to avoid.The Navigation System will calculate an alternative route for the
section of the route you wish to avoid.
If you stop route guidance and restart it, the blocked out section
entered is cancelled and has to be reset if required.
Tips


If the Avoid route from here fun ction is greyed out or the Na vig a-
tion System does not calculate an alternate route, local conditions
are making this impossible.


If the recommended detour route is not followed, the system
automatically calculates a new route from the current position
without given further consideration to the previously closed
section.
Map control buttonGeneral
There are various displays for maps and information
with different options possible.Fig. 149 Navigation: Map display with an IPD areaPossible map displays are:

Map and information display during route guidance with inac-
tive side menu
page 143.


Map display with active side menu
page 144
If light grey lines
fig.149 are shown on the map display, this
means that IPD sections/areas are being shown. IPD means “in-
progress-data”, i.e data collection is incomplete and consequently
they cannot be included for route guidance. These IPD
sections/areas are on the Navigation DVD and are represented on

Navigation (NAV) 144Th e fi g ure s
page 143, fig.15 0 a nd
page 143, fig.151 show you
the possible types of information in the map display:
Map orientation
Scale
Estimated distance to the next destination/stopover
Estimated time of arrival to the next destination/stopover
Ve hicle s ymbol
Example of selected map contents page 155
Turn list inserted in the Setup menu page 156
The map display modes can be changed page 151.
A crosshair with selection rectangle helps you select your destina-
tion with the aid of the map
page 148.
Route guidance is additionally shown by directional arrows in the
instrument cluster display (
page 113 or
page 114).
Tips
An underpass or a tunnel is shown by broken lines on the map
display up to a scale of 0.5 mile.
Map display with active side menu
The map display can be changed through the active
side menu.Fig. 152 Navigation: Map display with active side menu–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu

fig.152.
– Select the desired submenu item by rotating and
pressing the control knob and make your changes.
– Press the button, to leave the map side menu.If you have activated the Zoom function
page 146 or the
crosshairs
page 149 in the active side menu, you have to press
the button twice in order to leave the map side menu.
A1AA AA4A9A:
RETURN
RETURN