light AUDI A3 2016 Owner´s Manual

e-tron
overhangs, carports or similar structures . Switch
the ignition
off. Have the problem corrected by
an author ized Audi dealer or authorized A udi
Serv ice Facility .
• Elec tric s ystem: o verheated. Safel y park ve­
hicle and check coo lant
The coolan t leve l is too low or the coolant tem ­
pera ture is too high .
S top the vehicle in the outdoo rs as soon as it is
safe ly possible . Switch the ignition off.
Read the important safety precautions ¢.&.
in
Coolant on page 109 and check the coolant level
¢page 108.
If the coolant level is OK, the malfunction may be
caused by the system overheating . Let the vehi­
cle's electric drive system cool down for some
time .
If the message turns
off after cooling down and
sw itching the ign ition back on, you ca n continue
driving. Contact an author ized Audi dealer or au­
thor ized A udi Se rvice Facility immed iate ly to have
the ma lf u nction co rrected.
If the indicator lig ht stays on, contact an author­
ized A ud i dealer or authorized Aud i Serv ice Faci li­
ty .
Bil Drive system : sys tem fault! Pleas e contact
work shop
There is a malfunction in the plug-in hybrid sys ­
tem. Drive to an authorized Audi dealer or au­
thor ized Audi Service Facility immediate ly to have
the ma lfunction corrected .
II Drive sy stem: system fault! Restart not po s·
sible. Ple ase contact wo rkshop
There is a mal func tion in the plug -in hybrid sys­
tem . Do not open the engine compartment lid .
Drive to an a uth orized Aud i dea le r or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
II Batter y temperature too low . Engine start
not possible . See owner's manual
The outside temperature is too low. The vehicle
can no longer start at temperat ures below -18 °F
102
(- 28 °C) . Contact your author ized Audi dealer or
autho rized Audi Service Facility.
POWER LIMIT Warning! Limited power
If the indicator l ight turns on and this message
appears , there may be an engine cont rol mal­
funct ion. The
(m ind icator light in t he instr u­
ment clus ter a lso turns on. The e ng ine o utput is
reduced. Dr ive to an a utho rized Audi dea ler or
autho rized Audi Service Facility immedia tely to
have the malfunction corrected.
II e -tron mode : EV curr ently unavailable
This message appears w hen the 1-,$ 1 button is
pressed and the conditions for e lectric drive
mode are no t me t.
IIJ Vehicle sound: malfunction! Pedestrians
cannot h ear vehicle. P lease contact Service
if the indicator light t urns on and this message
appears, pedestrians and bicyclists can no longer
hear the vehicle when it is driving in electric
mode. Turn off the veh icle and switch to dr iv ing
with the gasoline e ngine . To activate the gasoli ne
engine, select the
Charge batt ery mode
¢page 103 with the kl"I button. Drive to a n au­
tho rized Audi dea le r or a uthorized Audi Service
Facility immediate ly to have the malfunction cor ­
rected.
Range display
Applies to vehicles: wit h pl ug-in hy brid drive
Fig. 89 Ins trument cluster example image: range disp lay
The range can be d isplayed in the on -board com­
p uter ¢
page 29.
Depend ing o n the selected p lug-in hybrid mode,
the d isp lay disp lays the follow ing informa tion:
Ill>

,....,
N
0 > co ,...., <J:) Lil ,...., <J:) ,....,
@ electric motor range or combined total range
@ gasoline engine range
© electric motor range
(D Tips
The values given are based on the latest con­
sumption values.
Plug-in hybrid mode
Applies to vehicles: with plug- in hybrid drive
You can select between one electric mode and
three hybrid modes.
dV Electric mode (EV mode)
EV mode is electric driving only.
EV mode is active at the beginning of every drive
depending on the operating status. The LED in
the
!<=I'! button turns on. The. indicator light al­
so turns on in the instr ument cluster display. The
gasoline engine stays switched off as long as the
battery charge level and climate conditions allow
it .
You can drive with only electric power at speeds
up to approximately 80 mph (130 km/h).
Hybrid modes
The electric motor and the gasoline engine work
efficiently together in every hybrid mode.
OQ!t Hybrid: the battery charge is used as much as
possible when this mode is switched on. This
mode is best suited for long distances.
O\Q!J Hold battery: the high-voltage battery charge
level is conserved as much as possible.
•& Charge battery: the high-voltage battery will
charge if the charge level permits it. This causes
an increase in fuel consumption.
@ Tips
-Applies to "Hold battery" and "Charge bat­
tery": the battery charge level can also de­
crease depending on the driving style.
- If you select the sport driving mode S when
in EV mode, the Hold battery mode is auto­
matically selected. You can select the EV
e-tron
mode again with the 1.:.1•! button
r:!;> page 104.
- if the la• I r:!;> page 104 button is pressed
while in sport driving mode S, the transmis­
sion switches automatically to normal mode
0.
Conditions for electric driving
Applies to vehicles: wit h plug-in hybrid drive
The EV mode can only be switched on if the fol­
lowing conditions are met:
- The cha rge level of the high-voltage battery
must be suff icient.
- The temperatu re of the high-voltage battery
must be adequate (outside temperatures not
below approximately 14°F / -10°C and not
above 104°F / 40°C)
- The speed must not be higher than approxi-
mately 80 mph (130 km/h).
- Kick-down must not be activated.
- The sport drive mode
S must not be selected.
EV mode is switched off if one or more of the
conditions are not met. The gasoline engine will
start automatically. The
E] ind icator light turns
on as a message in the instrument cluster. The
LED in the
l d• I button and the B indicator light
turn off.
Electric drive mode will not continue automati­
cally. Reactivate the EV mode
r:!;> page 104.
(D Tips
It may be necessary for the gasoline engine to
run longer for technical reasons, such as
when condensation accumulates in the en­
gine. Driving exclusively in electric mode is
not possible in this phase.
103

.... N
0 > CX)
rl I.Cl U"I
Statistics
Applies to vehicles: with plug-in hybrid drive
Fig. 93 Example image: e-tron stat istics
The statistics in the MMI l) show the distances
driven without emissions (electric) and with fuel.
The values are taken from on-board computers 1
and 2 .
Opening the statistics
.. Select: I MENU I function button >Car> Car sys­
tems
> e-tron statistics
.. Turn the control knob to switch between on­
board computer 1 and 2.
Electric power availability display
Applies to vehicles: with plug-in hybrid drive
Fig. 94 Instrument cluster; electric power availability dis­
p lay
The power currently available in the electric drive
system is displayed when you open the energy
flow indicator
r=> page 106.
The bars are filled in with different colors accord­
ing to the power status :
rl
~ 1> Not available in all Infotainment syste ms.
e-tron
@ -white: electric power currently available.
@ -green: electric power currently used .
The more segments that are colored in white in
the E-MAX area
0, the longer the maximum
power can be utilized . The segments turn off in
the E-MAX area when the maximum power can no
longer be utilized.
When the drive power is greatly reduced, the
drive mode will automatically switch to using the
gasoline engine.
The availability of power is generally restricted under the following conditions:
- The temperature of the high-voltage battery is
be very cold or very hot.
- The high-voltage battery charge level is low.
The power availability is not visible if the&] indi­
cator light turns on .
(D Tips
High power availability is necessary, for exam­
ple, when needing to accelerate quickly while
in electric driving mode to pass another vehi­
cle.
Vehicle tool kit and tire mobility kit
Applies to vehicles: with plug-in hybrid drive
Fig. 95 Luggage compartment: vehicle tool kit and tire
mo bility kit
The vehicle tool kit and the tire mobility kit (Tire
Mobility System) are located in the side trim pan-
el @ and @ in the luggage compartment. .,.
107

e-tron
The gasoline engine is no longer available be­
cause there is not enough fuel. Drive immediately
to a gas station.
Fuel filler door emergency release
A pp lies to ve hicles: w ith plug- in hy brid drive
You must use the emergency release to open the
fuel filler door when there is a malfunction
c::> page232 .
The tank is not vented. You can only fill a small
amount of fuel in the tank.
~ Fill only until the automatic fuel pump nozzle
turns off for the first time when it is operated
correctly.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
(D Tips
Pressure can escape if you open the tank cap
after using the emergency release. This can
create noises.
Charging
General information
A pp lies to veh icles: w ith plug -in hybrid drive
Two options are available for charging the vehi­
cle:
- Charge at a public charging station with a spe­
cial charging cable*
c::>page 112.
- Charge with household and industrial power
sockets using the Audi e-tron charging system
c::> page 112.
Environmental conditions when using the
charging system
-Operating temperature : -13 °F (-25 °C) to 95 °F
(+35 °C)
- Humidity:
5% to 95%, non-condensing
- 13,000 feet (4,000 meters) maximum above
sea level
110
Warnings when using the charging system
£
Surfaces can become very hot when
in direct sunlight.
&~
Incorrect use increases the risk of
electric shock.
~"-
Do not use any extensions cords or
cable reels.
~
Do not use any travel adapters.
~~
Do not use any power strips.
~~~
Do not use any charging cables with
damage to the electronics or the
connecting wires.
.&_ WARNING
-
Sockets that are installed incorrectly can
cause electric shock or fire when charging the
high-voltage battery using the vehicle charg ­
ing connection.
- Installation and setup of the household con­
nection for the Audi e-tron charging system
may only be performed by a qualified elec­
trician. The qualified electrician is thereby
fully responsible for adhering to applicable
standards and regulations.
- Make sure that the selected charging con­ nection is suitable for drawing 16 amps .
- Make sure that the
110 volt socket is
grounded and shielded from water.
- Always check the fuse for the GFI outlet be­
fore connecting the charge cable.
- Never use a damaged GFI outlet.
- Read and follow the safety precautions in
the Audi charging dock* assembly instruc­
tions.
.&_ WARNING
If you are not familiar with the socket or the
e lectrical installation or it has not been
checked by qualified experts, never use it for
charging. Even very low charging currents can
cause ser ious damage and in particular fires if
the socket or electrical installation is in bad
condition. If necessary, get expert assistance
~

.... N
0 > CX)
.... I.Cl U"I ,....,
I.Cl ....
-To reduce the risk of overheating during op­
eration, do not place the Audi e-tron charg­
in g system in d irect sunlight for long peri­
ods of time.
- If the temperature inside the control unit
rises above 176 °F (80 °C), the charg ing
process will stop automatically until the
temperature decreases back down to the normal range .
Attaching/changing the power/vehicle
cable
Applies to vehicles: with plug-in hybrid drive
Fig. 101 Contro l unit : loosening the cable
Fi g. 102 Contro l unit : attaching t he ca ble
Requirements:
.,. The charging process for the high -voltage bat ­
tery must be ended .
.,. The vehicle charging connector must be re­
moved from the vehicle charging port.
.,. The power cable must be removed from the
socket.
Loosening the cable
.,. If necessary, loosen the screw ©¢ fig. 101 us­
ing the screwdriver provided.
.,. Lift the lever @all the way up .
e-tron
.,. Pull the connecto r@ out just until you feel re­
sistance .
.,. Close the lever @unt il it is rest ing on the con-
nector @.
.,. Remove the connector @ completely.
Attaching the cable
.,. Lift the lever @ up slight ly¢ fig. 102.
.,. Insert the connector @ into the control unit
just unti l you feel resistance .
.,. Lift the lever @all the way up.
.,. Insert the connector @ all the way into the
control unit.
.,. Close the lever @ .
.,. Tighten the screw © using the screwdriver pro­
vided .
.&_ WARNING
- Always remove the power cable from the
socket before changing the power cable or
vehicle cable.
- Always follow the instructions given when
charging the high -voltage battery. Do not
remove the vehicle charging cable from the
socket during the charging process. End the
charging process before removing the vehi­
cle charging cab le from the socket.
- On ly change cab les in a dry environment.
- The Audi e-tron charging system may only
be used as one un it composed of power ca­
bles, the control unit and vehicle cable. We
recommend using only cables approved by
Aud i.
113

,....,
N
0 > co ,...., <J:) Lil ,...., <J:) ,....,
e-tron
Symbol Error code LED on the control
unit@ Meaning
Solution
480 Red
110 Red
Vehicle: charging unit
LED on the vehicle @
On
pulsating light
Green
Blinks for approxi-
mate ly one min ute
after leaving the vehi-
cle
On
Yellow
Flashes
On
Red
Flashes Flashes
Error in the control unit D
isconnect the control
unit from the power sup­
ply and reconnect it.
Flashes Ground fault interrupter
(G FI) triggered in the con ­
tra l unit . Reset the ground fault in­
terrupter with the
IOKI @
button r=>page 115,
fig. 106 .
Have the electri­
cal installation checked by
a qualified electrician if
the same d isplay appears .
Meaning Solution
High-voltage battery charging Remove
the charger, put the cap
on and close the cover on the
process is completed .
charging unit.
The high-voltage battery is charg-
ing or the vehicle is being a ir con-
ditioned/heated.
Charging timer was programmed
but the charging process has not
started yet . The LED in the button
@ r=>page 115, fig . 107 also
turns on.
Have the power supply or power
supply system inspected. Check
No power supply was recognized the status display on the control
even though the charging cable is unit
r=> table on page 118 . See an
plugged in . authorized Audi dealer or author-
ized Audi Service Facility for ass is-
tance if necessary.
The se lector lever in not in the P Move the selector lever into the P
position. position.
Check if the charging connector is
inserted correct ly
r=> page 116. Re-
The charging connector cou ld not move the charging connector and
be correctly locked in the vehicle
insert it into the charging port
charging port . again. See an authorized Audi
dealer or authorized Audi Service
Facility for assistance if necessary .
Error in charging system . The See an authorized Audi dealer or
high-voltage battery cannot be authorized Audi Service Facility for
charged. assistance if necessary.
119

.. Press the~ button @ r::?vpage 115, fig. 106 on
the control unit.
Unlocking the control unit
Requirement: the P IN must be activated.
.. Press any button on the control unit.
.,. PIN? appears on the display field .
.. Enter the PIN .
.. Press the
IOKI button @.
{O) Tips
-The PIN is deactivated in the factory default
settings.
- If you do not remember your PIN, contact
an authorized Audi dea ler or authorized
Audi Service Fac ility.
- If the first PIN entry differs from the second
ent ry, the first PIN entry is displayed.
- If nothing is entered w ith in 20 seconds of
th is, the set value is not changed.
Indicator Lights and
messages
Applies to vehicles: with plug-in hybrid drive
If the B indicator light turns on, the high-volt­
age battery is charging or is already completely
charged.
I f the . indicator light stays on, there is a mal­
function in the charging system. Have the prob­ l em corrected immediately by an authorized Audi
dea ler or authorized Audi Service Facility.
l'I Charging connector still attached. Driving
not possible
This message appears when the charg ing system
is sti ll connected to the veh icle. Remove the con­
nector
r::?v page 117, After charging.
1,1 AC charging: currently not possible
This message appears when the charging system
is incompatible. Only charge using the charging
system that is designed for your vehicle.
;::: 1,1 AC charging : system fault! Plea se contact 0
iii Service
e-tron
This message appears if there is a malfunction in
the charging system. Have the prob lem corrected
immediately by an authorized Audi dealer or au­
thori zed Audi Service Facility .
Vehicle charging
connector emergency
release
Applies to vehicles: with plug -in hybrid drive
There could be a malfunction if you are not able
to pull the vehicle charging connector out of the
vehicle charging port. You must use the emer­
gency release to release the vehicle charging con­
nector.
Requirement: the se lector lever must be in the P
position, the vehicle must be unlocked and the
charging process must have been ended or inter­
rupted.
.,. Press and hold the immediate charging button
@ r::?vpage 115, fig . 107 .
.. Press the [@l button on the remote control key
at the same time.
.. Remove the connector.
.. Drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to have
the malfunction corrected .
If the charging connector still cannot be removed
after using the emergency release, see an author­
ized Audi dealer or authorized Audi Service Facili -
ty for assistance .
Charging unit cover
emergency release
Applies to vehicles: with plug-in hybrid drive
~ Fig. 111 Front of the vehicle: cover emergency release U"I
121

e-tron
(D Tips
-You can set the timer a maximum of 7 days
in advance.
- You can operate the climate control in the
vehicle interior when the high-voltage bat­
tery is charging using the charging timer
c>page 116.
-Make sure the time and date match in the
MMI settings so that the timer can function
properly. Refer to the MMI Operating Man­
ual for setting the date and time.
- The auxiliary heating or auxiliary heating/
air conditioning* can run longer after the
departure time is reached.
Audi connect e-tron
services
General information
A pp lies to ve hicles : w ith plug- in hy brid drive
With Audi connect e-tron services l), you can ac­
cess various information or control individual
functions remotely using mobile devices (such as
a smartphone) or a web portal.
To use Audi connect e-tron services
l), please
note the following:
- You will need to register for Audi connect e­
tron services at
myaudiconnect .com. You can
access and manage e-tron services and features
at
etron.audiusa.com. If you need assistance
with your Audi A3 e-tron EV services, you can
contact customer service at 844-573-8766.
- Your mobile devices must be compatible.
A WARNING
Read and follow the safety precautions in
your MMI Operating Manual.
l) Wireless serv ice is provided by a thir d- part y provider.
-
Please contact your dea le r or call 877 -505 -2834 for more
informat ion about your carrier. Co nnected dev ices may
not be 4G -capab le. Full speeds avai lable but may be
slowed due to excessive usage, locatio n, coverage and
othe r factors. Coverage not available everyw here . See cov­
erage map for your Audi co nnect data carrier for more in­
format ion.
124
· Vehicle data
App lies to vehicles : wi th plug-i n hybrid drive
The Dr iver Information System collects data un­
der certain conditions and sends it to a server.
When data is stored, you can data such as the ex­
amples listed below using the Audi connect e­
tron services:
- Duration of the drive in hours and minutes,
- average speed driven in mph (km/h),
- distance driven in miles (km),
- average electric consumption .
For additional information on the Driver Informa­
tion System, refer to
c> page 28, Driver informa­
tion system.
Doors and lights
App lies to v ehicl es: wi th plug-in hybrid drive
You can access and display the current status of
the following vehicle data on your mobile devices
without having to be inside the vehicle.
- If the vehicle doors and lids are open/closed,
- If the parking l ights are on/off.
For additional information on opening and clos­
i ng the doors or for the vehicle light ing, refer to
c> page 3 5, Opening and closing or to c> page 46,
Exterior lighting.
(D Tips
-If the high-voltage battery is not charged,
the amount of access requests is limited to
15 after switching off the ignition. This
helps conserve the 12 volt vehicle battery.
You cannot contro l functions or access in­
formation if the charge level of the 12 volt
vehicle battery is too low.
- If at least two minutes have passed after
the last time the ignition was switched off,

,....,
N
0 > co ,...., <J:) Lil ,...., <J:) ,....,
you can reset the access counter back to "0"
as needed after switching the ignition on/
off again.
Vehicle status
Applies to vehicles: with plug- in hybrid drive
You can access various vehicle statuses using the
services, such as:
- high-voltage battery charge level,
- electric range,
- mileage,
- next inspection.
For addit ional information, refer to¢
page 101,
Power meter overview
and ¢ page 102, Range
display.
A WARNING
Do not be misled by the status report displays
by ignor ing messages and/or illuminated
warning and indicator lights in the vehicle.
This could lead to break downs in on the road,
accidents and serious injuries.
@ Tips
- If the high-voltage battery is not charged,
the amount of access requests is limited to
15 after switching off the ignition. This
helps conserve the 12 volt vehicle battery.
You cannot control functions or access in­
formation if the charge level of the 12 volt
vehicle battery is too low.
- If at least two minutes have passed after
the last time the ign ition was switched off,
you can reset the access counter back to "0"
as needed after switching the ignition on/
off again .
Vehicle position
Applies to vehicles: with plug -in hybrid drive
The vehicle collects data under certa in conditions
and sends it to a server.
When data is stored, you can data such as the ex­
amples listed below using the Audi connect e­
tron services:
- Vehicle location display
e-tron
-Display of one's own location
- Route to your vehicle
If your mob ile dev ice also has a navigation func­
tion, you can nav igate to your last known parking
location .
For example, you have the option to show the
route to your vehicle and to send the correspond­
i ng locations.
(D Tips
- The new parking locat ion cannot be deter­
m ined with this service if the vehicle is
moved after shutting the vehicle off and
w ithout switching the ignition on and off
again, for example when being towed or if
the vehicle is stolen .
-If the vehicle is moved and shut off again
using the second key, for example, the new
park position is transmitted to the
server af­
ter removing the key.
Charging
Applies to vehicles: with plug- in hybrid drive
You can contro l and access the high-voltage bat­
tery ch arging process remotely using these
serv­
ices. You have the following options:
- check the battery charge level,
- start/end the charging process,
- program the charging t imer with/without cl i-
mate control,
- deactivate/activate the charging timer.
For additional information, refer to¢
page 112,
Charging the battery with the Audi e-tron charg­
ing system.
A WARNING
Only perform charging functions on the high­
voltage battery if the vehicle is shut off cor­
rectly, is connected to a suitable socket and if
the ignition is switched off.
125

,....,
N
0 > co ,...., <J:) Lil ,...., <J:) ,....,
Trailer mode Driving with a trailer
General information
Your Audi was designed primarily for passenger
transportation .
If you plan to tow a trailer, please remember that
the additional load will affect durability, econo­
my and performance.
T railer towing not only places more stress on the
vehicle, it also calls for more concentration from
the driver.
For this reason, always follow the operating and
driving instructions provided and use common
sense.
Technical requirements
Trailer hitch
Use a weight-carrying hitch conforming to the
gross trailer weight. The hitch must be suitable
for your vehicle and trailer and must be mounted
securely on the vehicle's chassis at a technically
sound
location . Use only a trailer hitch with a re­
movable ball mount . Always check with the trail­
er hitch manufacturer to make sure that you are
using the correct hitch.
Do not use a bumper hitch.
The hitch must be installed in such a way that it
does not interfere with the impact -absorbing
bumper system . No modifications should be
made to the vehicle exhaust and brake systems .
From time to time, check that all hitch mounting
bo lts remain securely fastened.
When you are not towing a trailer,
remove the
tra iler hitch ball mount . This prevents the hitch
from causing damage should your vehicle be
struck from beh ind
~ ,&. .
Trailer brakes
If your trailer is equipped with a braking system,
check to be sure that it conforms to all regula­
tions .
Trailer mode
The trailer hydraulic brake system must not be
directly connected to the vehicle's hydraulic
brake system.
Safety chains
Always use safety chains between your vehicle
and the trailer.
Trailer lights
T ra iler lights must meet all regulations . Be sure
to check with your Aud i dea ler for correct wiring,
switches and relays .
Mirrors
If you are unable to see the traffic behind you us­
ing the regular outside mirrors, then you
must in­
stall extended mirrors . It is important that you
always have clear vision to the rear.
,8. WARNING
After removing the trailer hitch, do not store
it in your vehicle. In case of sudden braking,
the hitch could fly forward and injure you or
your passengers.
Operating instructions
Maximum trailer weight
A trailer for your vehicle is limited to a typical
class 1 or class 2 trailer.
Trailer load distribution Be sure the load in the trailer is held securely in
place to prevent it from shifting forward, back­
ward or sideways.
Never allow a passenger to ride in a trailer~.&.
in Driving instructions on page 128.
Engine cooling system
Towing a trailer makes the engine work harder. It
is important that the cooling system's perform ­
ance is up to the additional load. Make sure that
the cooling system has enough fluid.
Tire pressure
When towing a trailer, inflate the tires of your
vehicle to the cold tire pressure listed under "Full ..,.
127