AUDI A4 1995 B5 / 1.G AFC Engine Exhaust System Components Workshop Manual

26-1


Exhaust system components,
removing and installing

Note:

As a general rule, always install new seals and
gaskets and clamping sleeves.
Always replace self-locking nuts.
Install retaining rings and bolted connections as
specified Parts catalog microfiche.

Make sure that there is adequate clearance
between the body and the exhaust system
components.
Instructions for aligning the exhaust system free
of stress will be issued in a subsequent
Technical Bulletin.
Pa
ge 1 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1

26-2


Front-wheel-drive, engine code AFC

1 -
Locking nut
25 Nm (18 ft lb)
2 -
Three Way Catalytic Converter (TWC)
3 -
Gasket
4 -
Retaining ring When replacing always use a lubricant and
avoid damaging the rubber.
5 -
Rear muffler
6 -
Hex bolt 25 Nm (18 ft lb)
Pa
ge 2 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1

26-3


Note:
Handle the insulating elements with care; protect
from shock-like stresses and extreme bending.
Maximum deflection 10 . 7 -
Retaining ring
8 -
Center muffler
9 -
Clamping sleeve
40 Nm (30 ft lb)Tighten evenlyInstalled horizontally in vehicle
10 -
Hex bolt
11 -
Exhaust pipe, right front Only for models with automatic
transmission
12 -
Seal
13 -
Exhaust pipe with insulating element, left
front Only for models with automatic
transmission
Pa
ge 3 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1

26-4


14 -
Exhaust manifold
15 -
Hex nut
30 Nm (22 ft lb)
16 -
Exhaust pipe, left front
17 -
Exhaust pipe with insulating element,
right front
18 -
Heated Oxygen Sensor (HO2S) 50 Nm (37 ft lb)Testing Repair Manual, 2.8 Liter V6
OBD II Fuel Injection Ignition, Repair
Group 24 Lubricate threads with G5G5 must not get into slots on HO2S probe
body
Pa
ge 4 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1

26-5


All-wheel-drive, engine codes AFC

Note:
Handle the insulating elements with care; protect
from shock-like stresses and extreme bending.
Maximum deflection 10 . 1 -
Exhaust manifold
2 -
Gasket
3 -
Hex nut
30 Nm (22 ft lb)
4 -
Heated Oxygen Sensor (HO2S) 50 Nm (37 ft lb)Testing Repair Manual, 2.8 Liter V6
OBD II Fuel Injection Ignition, Repair
Group 24 Lubricate threads with G5G5 must not get into slots on HO2S probe
body
5 -
Three Way Catalytic Converter (TWC) with
insulating element, left
Pa
ge 5 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1

26-6


6 -
Three Way Catalytic Converter (TWC) with
insulating element, right
7 -
Clip
40 Nm (30 ft lb)
8 -
Hex bolt 25 Nm (18 ft lb)
9 -
Rear muffler
10 -
Retaining ring When replacing always use a lubricant and
avoid damaging the rubber.
11 -
Retaining ring When replacing always use a lubricant and
avoid damaging the rubber.
12 -
Center muffler
Pa
ge 6 of 6 Exhaust s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.26.1