sensor AUDI A4 1995 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

During "Basic Setting" function 04 with VAG 1551 scan tool and/or each time the DTC memory is erased, all learning
requirement displays are set to 0 in order to force new learning of the oxygen sensor learning values after the shop visit.
At each start, coolant temperature less than 40 C (104 F), the learning requirement is forced in all learning ranges. If there is a large learning value deviation (from the stored learning value to the newly learned value) in the learning
process, all learning requirement displays are reset to 0.
If there is successful learning, the learning requirement values of the respective learning ranges (display field 2) are set to 1.
Pa
ge 261 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-186

X
X
X
X
X
X
X
X
Meaning of 8-digit oxygen sensor learning requirement display

1 = Idle (bank 1)

2 = Idle (bank 2)

3 = Partial throttle 1 (bank 1)

4 = Partial throttle 1 (bank 2)

5 = Partial throttle 2 (bank 1)

6 = Partial throttle 2 (bank 2)

7 = Partial throttle 3 (bank 1)

8 = Partial throttle 3 (bank 2) Display value "0" = Request for new learning.
Display value "1" = Learning process ended.
Pa
ge 262 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-187
Display group 009 Display shows
Specified display value
Designation
Basic setting 9
1 2 3 4 ... % 1 = Oxygen sensor control (bank 1)
... % 2 = Oxygen sensor control (bank 2)
0 - 99% 3 = Duty cycle (triggering)-EVAP canister purge regulator valve -N80-
0% and/or greater than 95% 4 = Throttle angle - at idle: 0%; at wide open throttle: > 95% Note:
The oxygen sensor control should always be evaluated only after successful learning ( learning requirement display, display
group 007 and/or 008, display field 4) in both "Basic Setting" function 04 and "Read Measuring Value Block" function 08.
Pa
ge 263 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-189
Display group 010 Display
shows Specified display value
Designation
Basic setting
10
1 2 3 4 Difference between display values 1 and 2
less than 8% 1 = Total of oxygen sensor control (bank 1) and momentary
oxygen sensor learning value (bank 1)
2 = Total of oxygen sensor control (bank 2) and momentary
oxygen sensor learning value (bank 2)

At times greater than 0.6 V and/or less than
0.3 V (display must fluctuate) 3 = Voltage signal-bank 1 heated oxygen sensor 1
4 = Voltage signal-bank 2 heated oxygen sensor 1 Note:
The total of the oxygen sensor control and oxygen sensor learning value shows the total effect of the oxygen sensor control.
Bank differences can be evaluated directly by comparing display field 1 with display field 2.
Pa
ge 265 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-190
Test table display group 010 Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
1/2 Difference between display value
1 (bank 1) and display value 2
(bank 2) greater than 8%
Spark plug faultyIntake air leak on one side Fuel injectors faulty - Repair cause
- Check DTC memory page 01
-13

and/or check fuel injectors page 24-
29


Heated Oxygen Sensor
(HO2S) faulty (dirty) - Check DTC memory page 01
-13

and/or display fields 3 and 4

Mechanical engine basic
setting (valve/camshaft
timing) not OK
Repair Manual, 2.8 Liter V6 2V
Engine Mechanical, Engine Code(s): AFC, Repair Group 13
- Check valve/camshaft timing
Pa
ge 266 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-191

Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
3/4 Display does not fluctuate-constant
between 0.0 - 0.3 V and/or between
0.6 - 0.9 V
Fuel injector faulty- Check fuel injectors page 24
-29

Spark plug faultyLarge intake air leak Engine Coolant Temperature
(ECT) sensor -G62- faulty EVAP canister purge
regulator valve -N80- - Check spark plug
- Repair cause
- Check DTC memory page 01
-13

and/or check -G62-
- Check using output diagnostic test
mode page 01
-145
and/or check -
N80-

Heated Oxygen Sensor
(HO2S) -G39- faulty or dirty Oxygen Sensor (O2S) heater
-Z19- does not function - Check DTC memory page 01
-13

and/or check -G39-
- Check -Z19- page 24
-49

Fuel system pressure too
high or too low - Check fuel pressure regulator and
residual pressure page 24
-20


Constant 2.550 V Short to positive (B+) through:
Heated Oxygen Sensor
(HO2S) -G39- wiring Engine Control Module
(ECM) -J192- - Check -G39- page 24
-49Pa
ge 267 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-192

Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
3/4
Constant value between 0.350 -
0.450 V Open circuit in:
Heated Oxygen Sensor (HO2S) -G39-
wiring Engine Control Module (ECM) -J192-- Check -G39- page
24
-49


Constant 0.000 V Short to ground in:
Heated Oxygen Sensor (HO2S) -G39-
wiring Engine Control Module (ECM) -J192-- Check -G39- page
24
-49


Notes on display field 4:
The display value at times must drop below 0.3 V
and exceed 0.6 V. Display values less than 0.40
V indicate lean condition; greater than 0.40 V
indicate rich condition.

HO2S voltage U (mV) vs. Lambda ( ) A - HO2S voltage (mV) high
Rich mixture (fuel excess or lack of air)
High CO value
B - Oxygen sensor probes voltage (mV) low
Pa
ge 269 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

If there is engine damage (oil burning because of faulty piston)
If a knock sensor malfunction is recognized in DTC memory, ignition map switching is blocked.
Notes on display field 4:
Knock control is active starting at an engine load greater than 40% Display groups 013 and/or 014. The ignition timing point retarding values are only used when knock control is "active."
Pa
ge 274 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-196
Display groups 013 and 014
Notes on display fields 2, 3 and 4:
Knock control is active starting at an engine load greater than 40%. If the engine load exceeds 40%, the current ignition timing
point retarding value is displayed; if the engine load drops below 40%, the last values used are displayed constantly.
If there is audible knocking without recognizable retarding of the ignition timing point, the engine speed should be increased
over 3500 RPM for 5 seconds to initiate the knock sensor malfunction recognition (On Board Diagnostic).
If an ignition timing point retarding value of one cylinder deviates from the others, the following malfunctions are possible:

Loose subassemblies
Corrosion on the harness connector
Engine damage (e.g. oil combustion with faulty piston)
If there are high ignition timing point retarding values on all cylinders of bank 1 or bank 2, the following malfunctions are
possible:
Corrosion on the harness connector display groups 015 and 016 Knock sensor tightening torque, 20 Nm (14 ft lb), not OK
Open circuit display groups 015 and 016 Knock sensor faulty
Pa
ge 276 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-197
Display group 015 Display shows
Specified display value
Designation
Basic setting 15
1 2 3 4 ___ RPM 1 = Momentary engine speed display group 003, display field 1 _._V 2 = Knock sensor signal (cylinder 1)
_._V 3 = Knock sensor signal (cylinder 2)
_._V 4 = Knock sensor signal (cylinder 3) Display group 016 Display shows
Specified display value
Designation
Basic setting 16
1 2 3 4 ___ RPM 1 = Momentary engine speed display group 003, display field 1 _._ V 2 = Knock sensor signal (cylinder 4)
_._ V 3 = Knock sensor signal (cylinder 5)
_._ V 4 = Knock sensor signal (cylinder 6)
Pa
ge 278 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1