AUDI A4 1995 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-212
If the trip status display is set to "1" when the readiness code is regenerated, but the corresponding display value of the
readiness code is not set to "0", the diagnosis was carried out but recognized as not OK by the engine control module. In this
case, the DTC memory should be checked to determine malfunctions and/or to carry out a selective diagnosis:

For three way catalytic converter diagnosis (Bank 1 and 2) also check display groups 035, 036 and 044.
For the Evaporative Emissions (EVAP) system leak diagnosis, also check display group 030.
For the Secondary Air Injection (AIR) system throughput and leak diagnosis, also check display groups 020 and 021.
For oxygen sensor diagnosis, also check display groups 032, 033, 034, 041, 042 and 043.
For oxygen sensor heating diagnosis, also check display group 040.
For the Exhaust Gas Recirculation (EGR) system throughput diagnosis, also check display group 017.
Display
shows Display specified
value Designation/diagnosis
Basic setting
29
1 2 3 4 X X X X X X 1 = Readiness Code
X X X X X X X X 2 = Trip Status display
0 - 40 3 = Counter for warm-up phases without new malfunctions except for "combustion
misfiring" and/or "oxygen sensor control"
0 - 40 4 = Counter for warm-up phases without new malfunctions except for "combustion
Pa
ge 301 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

misfiring" and/or "oxygen sensor control"
Pa
ge 302 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-213
Notes on display field 1:

All readiness code values are set to "1" by disconnecting the ECM harness connector and/or disconnecting the battery,
and every time DTC memory is erased (both with address word 01 function 05 and with address word 33 mode 4).
To regenerate the readiness code, take a drive of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with manual
transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear ("mixed city
and highway" trip).
Value "0" = Diagnosis carried out
Value "1" = Diagnosis not OK and/or diagnosis not carried out yet
X
X
X

X
X

X
Meaning of the 6-digit "readiness codes"

1 = Three way catalytic converter diagnosis (Banks 1 and 2)

2 = ----

3 = Evaporative Emissions (EVAP) throughput diagnosis

4 = Secondary air system throughput and leak diagnosis (Always "0" for vehicles without
secondary air injection system)

5 = ----

6 = Heated oxygen sensor diagnosis (flank rise and/or flank fall time of the voltage signal of
heated oxygen sensors in front of three way catalytic converters

7 = Oxygen sensor heating diagnosis (all four O2S heaters)

8 = Exhaust Gas Recirculation (EGR) throughput diagnosis
Pa
ge 303 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-214
Notes on display field 2:

The display values are set to "0" at each start, since the function capability of components and systems that can affect the
exhaust are checked again and again.
Leak testing of the EGR system is only carried out after a preceding cold start (water temperature -10 C to 30 C (14 to
86 F). Value "0" = Diagnosis not carried out yet
Value "1" = Diagnosis carried out
X
X
X
X
X
X
X
X
Meaning of 8-digit "Trip Status" display

1 = Three way catalytic converter diagnosis, banks 1 and 2
(for diagnostic conditions display group 044)
2 = Exhaust Gas Recirculation (EGR) system leak testing

3 = Evaporative Emissions (EVAP) throughput diagnosis
(for diagnostic conditions display group 030)
4 = Secondary air injection system throughput and leak testing
(always "0" on vehicles without secondary air injection system; for diagnostic conditions
display groups 020 and 021)
5 = Oxygen sensor control diagnosis
Pa
ge 304 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

(for diagnostic conditions display groups 007 and 008)

6 = Heated oxygen sensor diagnosis (flank rise and/or flank fall time of the voltage signal on
the heated oxygen sensor in front of three way catalytic converter; for diagnostic conditions
display group 042)
7 = Oxygen sensor heating diagnosis (all four O2S heaters)

8 = Exhaust Gas Recirculation (EGR) system throughput diagnosis
(for diagnostic conditions display group 017)
Pa
ge 305 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-215
Notes on display fields 3 and 4:

Display field 3 evaluates all malfunctions except "Combustion misfiring and oxygen sensor control."
Display field 4 evaluates only the malfunctions "Combustion misfiring and oxygen sensor control"
If a malfunction is recognized, the corresponding counter will be set to "40." The counter is decremented, during a new
start, when the trip was started at coolant temperature of 49 C (120 F) and ended at a water temperature of 71 C
(160 F) and the malfunction is no longer recognized. However, decrementing is only allowed if the MIL has not lit up yet
or is no longer lit. When counter status "0" is reached, the recognized malfunction is erased. If the DTC memory is erased, the counter is also decremented.
Pa
ge 306 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-216
Display group 030 (EVAP system diagnosis)
Notes:

Display group 030 is only considered on vehicles with sensor for EVAP canister -G172-.
If the value of the EVAP throughput diagnosis is not set to "0" in display group 029, display field 1 during regeneration of
the readiness code, and/or there is a malfunction in DTC memory that relates to the EVAP system, display group 030 is
used to carry out a selective diagnosis.
Since the EVAP system is automatically shut off during "Basic Setting" function 04, display group 030 can only be
evaluated using "Read Measuring Value Block" function 08.
When diagnostic conditions are fulfilled, the Engine Control Module (ECM) checks the EVAP system at each start with the
help of the sensor for EVAP canister -G172-. The pressure between the EVAP canister and EVAP canister purge
regulator valve is measured with the sensor for EVAP canister -G172-.
The diagnostic conditions are only fulfilled during a drive of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with
manual transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear. If
the diagnostic conditions are fulfilled, the diagnosis is active. To get the diagnosis results, you have to drive approx. 1-1/2
to 5 minutes under the diagnostic conditions, while the pressure has to be measured with closed EVAP canister purge
regulator valve. First, the pressure must be measured with the valve closed. You can get the valve to close most easily by
having a preceding deceleration fuel shut-off. If there are problems in shutting the EVAP canister purge regulator valve by
deceleration fuel shut-off, it can also be shut by running display group 030 in "Basic Setting" function 04. Then the
pressure has to be measured again in "Read Measuring Value Block" function 08 with valve fully open.
The diagnosis is recognized as OK if the EVAP system low pressure measured in display field 1 is greater than the actual
calculated EVAP system minimum low pressure in display field 2.
Pa
ge 307 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

If the EVAP system is recognized as OK during the first diagnosis, the diagnosis is discontinued. If the EVAP system is
recognized as not OK, the EVAP canister throughput test is continued.
If the EVAP system throughput diagnosis is to be carried out selectively and/or after a diagnosis, shut the engine off and
start again.
Pa
ge 308 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-217

Display shows
Display/specified value
Designation/diagnosis
Basic setting 30
1 2 3 4 -- mbar 1 = Currently measured EVAP system under pressure
-- mbar 2 = Currently calculated EVAP minimum under pressure
0 - 99% 3 = Duty cycle (triggering) EVAP canister purge regulator valve
0% = completely open
99% = completely closed
X X X X X 4 = Diagnosis status and/or result Note on display field 2:
An under pressure calculated from the momentary throughput of the Mass Air Flow (MAF) sensor (intake air mass) is
displayed.
Notes on display field 4:
0 1 X X X = Diagnosis carried out, diagnosis OK
1 0 X X X = Diagnosis carried out, malfunction recognized, diagnosis is continued
The display positions marked with X do not have to be fulfilled to evaluate the diagnostic status and/or result.
Pa
ge 309 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-218

X
X
X
X
X
Meaning of 5-digit "Diagnostic Status and/or Result"

1 = Diagnostic conditions during test drive (approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with
manual transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably
in 4th gear)
Manual transmission: 8 - 45%
Automatic Transmission: 8 - 20%
Value "0" = Diagnostic conditions not fulfilled
Value "1" = Diagnostic conditions fulfilled
Engine speed: 1600 RPM - 4500 RPM ( display group 003) Intake air through Mass Air Flow (MAF) sensor: 22 g/sec - 56 g/sec ( display group 019) Throttle angle: ( display group 003)

2 = Pressure measurement w/EVAP canister purge regulator valve completely closed
Value "0" = Pressure measurement not completed yet
Value "1" = Pressure measurement completed

3 = Pressure measurement w/EVAP canister purge regulator valve completely open
Value "0" = Pressure measurement not completed yet
Value "1" = Pressure measurement completed

4 = Diagnostic status
Pa
ge 310 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1