AUDI A4 1995 B5 / 1.G Rear Door Trim Workshop Manual

70-23


Rear door trim Component locations, overview

1 -
Door trim
Removing installing page 70
-25
2 -
Clip locator
3 -
Outer connecting piece
4 -
Outer filler piece
5 -
Rear door trim insulation
page 70
-37
6 -
Foam seal
7 -
Inner filler piece
8 -
Inner connecting piece
9 -
Guide for locking knob
10 -
Interior door handle
Removing page 70
-27
11 -
Trim panel
Removing page 70
-36
12 -
Window crank handle
Pa
ge 1 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-24


13 -
Speaker (woofer)
Removing page 70
-16
14 -
Door warning and footwell lights
Removing page 70
-33
Pa
ge 2 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-25

Rear door trim, removing and installing


Vehicles with manual window crank page 70
-28
. - Remove bolt -1-.
Tightening torque: 1.5 Nm (13 in. lb)
- Pull handle shell -2- downward out of door trim -4-.
- Remove nut -3- (1x).
Tightening torque: 2.5 Nm (22 in. lb)

Note:
The Bowden cable for the inside door mechanism and the electrical
harness connectors are not disconnected until after removing door trim -3-
. - Remove bolts -1- (2x).
Tightening torque: 1.5 Nm (13 in. lb)
- Lift door trim -3- up and out of door shell.
- To install, bases -4- for detent notches -2- (7x) must be fully installed.
Pa
ge 3 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-26


Note:
When installing, make sure that hook -3- faces upward. - Pull Bowden cable -1- out of guide -2- and remove.
- Disconnect electrical harness connectors.
Pa
ge 4 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-27

Interior door handle, removing


- Remove door trim page 70
-25
.

- Press spring -2- in direction of arrow -A- and remove interior door
handle -1- toward front.
Pa
ge 5 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-28

Rear manual window crank, removing
and installing


- Press in flat side of flat-head screwdriver in direction of arrow -1-.
- Rotate flat-head screwdriver in direction of arrow -2-.
- Pull off cover in direction of arrow -3-.

- Remove bolt -1-.
Tightening torque: 2.5 Nm (22 in. lb)
- Remove manual window crank -2- and base -3-.
Pa
ge 6 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-29

Rear door manual window crank installation
position

Illustration shows left manual window crank (right-side is mirror of left).
A - Driving direction
a - Installation position with window closed, at 40 20 angle toward
rear.
Pa
ge 7 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-30

Release button, adjusting


- When locked, release lever must not project more than dimension -a-.
Dimension -a-: 0-2 mm countersunk
Pa
ge 8 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-31

Power window switch, removing and
installing


- Remove door trim page 70
-25
.

- Remove insulation page 70
-37
.

- Use screwdriver to remove retaining tabs -1-.
- Remove power window switches -2-.
Pa
ge 9 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2

70-32

Bass speaker, removing


- Remove door trim page 70
-25
.

- Remove insulation page 70
-37
.

- Remove bolts -1- (3x).
Tightening torque: 1.5 Nm (13 in. lb)
- Remove bass speaker -2-.
Pa
ge 10 of 17 Rear door tri
m
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.2