AUDI A4 1996 B5 / 1.G Relay Panel Fuse Panel Workshop Manual

97-1


Relay panel, fuse panel

CAUTION!

Disconnect the battery Ground (GND) strap
before working on the electrical system.

Notes:

Before disconnecting the battery, determine the
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience
features, etc.) as outlined in this Repair Manual
or the Owner's Manual.
Pa
ge 1 of 5 Rela
y panel, fuse
panel
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.97.1

97-2

Fuse panel, removing and installing


- Carefully pry off side cover from instrument
panel.

- Remove both mounting bolts -B- (2 Nm or 18 in. lb), then depress tabs
-C- and remove fuse panel -A- toward rear.
Pa
ge 2 of 5 Rela
y panel, fuse
panel
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.97.1

97-3

Central electric unit and relay panel,
removing and installing


Note:
The relay panel is only required for certain
optional equipment, and is not standard
equipment.

- Remove driver's-side knee bar.

Repair Manual, Body Interior, Repair Group
68


- Remove both mounting bolts -C- (2 Nm or 18 in. lb) and disconnect all
screw connections -D- and -E- if necessary.
- Pull out relays and control modules and then unclip relevant relay
panel.
- Remove central electric unit -B- and relay panel -A-from bottom.
Pa
ge 3 of 5 Rela
y panel, fuse
panel
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.97.1

97-4

Electronics box (E-box) in plenum
chamber, removing and installing


- Remove mounting bolts (arrows) and pull off cover.
- When installing, press cover on by hand and tighten mounting bolts in
diagonal sequence. Tightening torque: 4 Nm (35 in. lb) (also see
information on cover).
- Remove engine control module and, if necessary, remove auxiliary
relay panel/auxiliary fuse panel Page 97
-5 .
- Disconnect harness connector at connector station.
- Pull out engine wiring harness together with rubber grommet from
opening in electronics box.

Note the following when installing: - Remove both nuts -A- (4 Nm or 35 in. lb).
- Lift electronics box off studs at rear and pull out of mount -B-.
- Install in reverse order of removal.
- Always replace seal -C-: seal must not overlap opening in body and
edge of sheet metal.
Pa
ge 4 of 5 Rela
y panel, fuse
panel
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.97.1

97-5

Auxiliary relay panel/auxiliary fuse
panel, removing and installing

Location: in footwell, bottom left.

- Remove nut -A- (2 Nm or 18 in. lb) and self-tapping screw -B-.
- Remove relay and control module, unclip relay carrier and, if
necessary, unclip auxiliary relay panel.
- Pull out auxiliary relay panel from retainers and remove from below.
- Install in reverse order of removal.
Pa
ge 5 of 5 Rela
y panel, fuse
panel
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.97.1