torque AUDI A4 1997 B5 / 1.G Engine Oil Level Checking Workshop Manual

12

Engine oil, oil filter; replacing


Notes:
Replace oil drain plug seal.
Use VAG 1307 or 1358 to extract engine oil. For
rapid extration of oil on V6 engines use probe
VAG 1358A/4.
Please observe waste disposal requirements!
Do not clean and re-use oil fiter!
Tightening torque of oil drain plug: 40 Nm (30 ft
lb).
Engine oil capacity (with filter change)

1.8 liter 5V turbo: 3.5 liter (3.7 qt)
2.7 liter V6 5V turbo: 6.0 liter (6.3 qt.)
2.8 liter V6 5V: 5.7 liter (6.0 qt.)

Procedure

- Loosen oil filter with tensioning strap (e.g. Hazet
2171-1 or equivalent) and remove.
Pa
ge 3 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

22

Spark plugs, replacing


Note:
To replace spark plugs, use Spark Plug Wrench 3122B. - Remove engine cover.
- Install new spark plugs.

Tightening torque: 30 Nm (22 ft lb)
Pa
ge 16 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

30

Note:
It is not possible to adjust the tension of the V-
belt for the coolant pump.

- Tighten viscous fan mounting to 45 Nm.

- Install ribbed belt over crankshaft pulley, viscous
fan pulley and power steering pump pulley. If
necessary, pull belt upward using a suitable tool.

Vehicles with air conditioner - Turn ribbed belt tensioning element in direction of arrow.
- Install ribbed belt over Generator pulley last. Release tensioning
element.
- Check that ribbed belt is properly seated.

Routing of ribbed belt Page 32

- Install ribbed belt for A/C compressor.

Routing of ribbed belt Page 32
- Apply torque wrench to hex on tensioning roller and tension with a
torque of 25 Nm
- Tighten bolts -A- to 20 Nm
Pa
ge 24 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

31

All models

- Start engine and check belt running.

- Check again to ensure that bolts for coolant
pump pulley are tightened to correct torque.
Pa
ge 25 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

42

Note:
Fit filler hook into one of the oil deflector cap -4-
slots placed on the filler opening.

CAUTION!

Do not press filler hook upward or oil
deflector cap can be pushed off.

- Reinstall ATF filler plug -2-.


Tightening torque: 80 Nm (59 ft lb).

-
Press key to advance program.

- Press keys -0- and -6- to select address code -
06- "Data Transmission Ended" and confirm with
key -Q-.
Pa
ge 40 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

49

Wheel bolts, tightening to specified
torque


Trim cap

Puller -A- for removing the trim cap is in the vehicle tool kit.
Wheel bolts
The adapter for loosening and tightening the anti-theft wheel bolts is in the
vehicle tool kit.
Note:
Ensure that the wheel bolts are tightened diagonally and alternately to the
following tightening torque:
Tightening torque: 120 Nm (89 ft lb)
Correct installation of wheels
When installing the wheels, note the following points to ensure that the
wheels remain secure at all times: - After completing work, replace adapter in vehicle tool kit.
Always tighten the wheel bolts to the specified torque; excessive
torque can distort the wheel bolt seats in the rim.
Pa
ge 49 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

50

When installing a wheel, do not torque down
the first wheel bolt immediately (for instance,
with an impact wrench). This would prevent the
other bolts from centering the wheel properly
when they are threaded in; the rim could then
come loose, even though the bolts have been
tightened to the specified torque.
Before installing the wheels, examine the seats
of the wheel bolts and the contact surfaces
between the rims and the hubs for rust and
corrosion. Clean off these parts if necesary,
otherwise this can affect the clamping force of
the bolts after installation, and the rims can
come loose.

WARNING!
If the points listed above are not observed,
the wheel mountings can come loose and the
wheel bolt seats can become distorted.
This distortion may be very slight and not
visible to the naked eye.
Even this slight distortion of the wheel bolt
seats can prevent the rims from being held
firmly and the wheels will come loose
repeatedly.
Pa
ge 50 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

75

Wiper blades, adjusting parked position

Check wiper blades and arms for signs of
damage, replace if necessary.
Parked position:
Windshield:

Tightening torque of wiper arms: 16 Nm (12 ft lb). - Position wiper blades on markings -A- in windshield and tlghten.
- Operate single wipe control.
- Align wiper arms and tighten.
Pa
ge 76 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6