AUDI A4 1997 B5 / 1.G Trim Avant Workshop Manual

Page 1 of 9

70-98


Trim (Avant)

Tailgate trim, removing and installing


Note:
When installing the lower trim, guide bars must be inserted in upper trim. - Remove bolt -1-.
- Tightening torque: 1.2 Nm (10 in. lb)
- Unclip lower tailgate trim -2-.
- Unclip upper tailgate trim -3-.
Pa
ge 1 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 2 of 9

70-99

C-pillar trim, removing and installing


- Remove side panel page 72
-75
.

- Remove side trim page 70
-102
.

Note:
When installing, ensure retaining clips are positioned properly. - Remove C-pillar trim using assembly hooks.
Pa
ge 2 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 3 of 9

70-100

D-pillar trim, removing and installing


- Remove side panel page 72
-75
.

- Remove side trim page 70
-102
.

Removing

- Remove D-pillar trim (use assembly hooks for
easier removal).

Installing
- Install trim at roof panel trim, guide centering drift to centering hole and
position retaining clips.

CAUTION! - Swing D-pillar trim in direction of arrow and attach to body.
When installing D-pillar trim, it must be inserted in roof panel trim
groove.
Pa
ge 3 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 4 of 9

Current retaining clips are not right-angled. If clips were
separated from D-pillar trim during removal, they must be
repositioned at the correct angle.
Pa
ge 4 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 5 of 9

70-101

Roof panel trim, removing and installing


- Remove side panel page 72
-75
.

- Remove rear panel trim page 70
-103
.

- Remove side trim page 70
-102
.

- Remove D-pillar trim -3- page 70
-100
.

Note:
To install, insert centering drifts in locating holes -2- and correctly position
retaining clips. - Remove bolts (arrow) 2x and unclip trim -1-.
Tightening torque: 1.5 Nm (13 in. lb)
Pa
ge 5 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 6 of 9

70-102

Left and right-side trim, removing and
installing


- Remove side panel page 72
-75
.

- Remove tailgate seal in area of loading
edge/side panels.

- Remove loading edge page 70
-103
.

- Lift front edge of cover for seat belts and
unclip.

- Lift up cover for latch bracket for rear
backrest.

- Remove cap.
Disassembling tie-down page 70
-104
.

Installation is the reverse of removal. - Remove bolts (arrow).
Tightening torque: 1.5 Nm (13 in. lb)
- Unclip side trim and pull up and over belt guide and latch bracket.
- If changing completely, disassemble seat belt webbing underneath rear
seat.
Pa
ge 6 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 7 of 9

70-103

Rear panel trim, removing and installing


- Remove tailgate seal in area near trim.

- Remove bolts (2x).

Tightening torque: 1.5 Nm (13 in. lb)

Note:
When installing, install centering drifts in locating holes and position
retaining clips properly. - Remove rear panel trim upward.
Pa
ge 7 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 8 of 9

70-104

Tie-down (Avant), removing and
installing


- Remove bolts (2x) for each tie-down.

Tightening torque: 4.5 Nm (40 in. lb)

- Remove trunk mat.

- Remove side trim page 70
-102
.

- Remove trunk mat backing and brackets for
front and rear tie-downs.
Installation is the reverse of removal

Tightening torques for front brackets:
Phillips-head screw (2x with front-wheel drive; 4x with all wheel drive):
6 Nm (53 in. lb)
Hex bolt (1x - only for front wheel drive): 30 Nm (22 ft lb)
Pa
ge 8 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10

Page 9 of 9

70-105


Tightening torques for rear brackets:
Bolt in floor: 23 Nm (17 ft lb)
Bolt in rear panel: 10 Nm (7 ft lb)
Pa
ge 9 of 9 Trim
(Avant
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.70.10