light AUDI A4 1998 B5 / 1.G Engine Oil Level Checking User Guide

69

Setting low beam alignment of driver's side
headlight

- Move Beamsetter into position in front of the
vehicle so it is aligned with the vehicle and
Beamsetter box is 30 to 70cm (12 to 28 in.) from
the driver's side headlight.

- Switch headlights ON in low beam position.

- Align Beamsetter box so it is centered on the
headlight (align vertically then horizontally).

Note:

Use the arrows on the Beamsetter box as a
guide.
You may want to use a straight edge or tape
measure, because alignment must be within
3cm (1.2 in.) of the center of the headlight.

- Without moving the Beamsetter, slide Broad-
band sight toward center of vehicle (Broad-band
sight can also be moved up and down for a
better position).
Use Broad-band sight to make final alignment of
Beamsetter box to vehicle by:
Pa
ge 69 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

70

Note:
Try using corners of the headlight housings or
two screws that are the same height and as far
apart as possible on the vehicle.

- Carefully tighten hand wheel without changing
Beamsetter position.

- Find correct State or Province Inclination %
specification for the low beam adjustment (If
there is no local specification use 1.2%).

Note:
DO NOT use the Inclination % molded into the
plastic of the headlight housing near the
headlight adjustment screws; it is for Europe
only!

- Set Beamsetter "Scaled wheel" to the proper low
beam inclination %.

- Adjust height (vertical) alignment first. Turn
headlight height adjuster screw to align the
upper edge of the flat portion of the beam with
the center horizontal line of the grid on the
Beamsetter pattern screen.
Pa
ge 71 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

71

Note:
VOL is the correct beam pattern for both right
and left headlights.

Note:
If the height alignment changed, readjust.
Checking driver's side headlight high beam alignment - Adjust lateral (horizontal) alignment of driver's side headlight so that
the peak (highest point) of the headlight beam pattern aligns with the
right edge of the target box of the grid on the pattern screen (it should
match the VOL pattern shown on the Beamsetter box).
- Switch headlights ON in high beam position.
- Realign Beamsetter box with the high beam headlight if necessary.

- Set Beamsetter "Scaled wheel" to 0%.
- Cover low beam lamp (use hand or small piece of cardboard) and
check that the "hot spot" of high beam pattern is centered on the
square target box of the pattern screen.
Pa
ge 72 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

72

Note:
High beam pattern is built into the reflector
design and cannot be adjusted separately.
If high beam pattern is way out of adjustment:

- Inspect for reflector damage.

- Replace reflector if needed.

Note:
Always align headlight in the low beam position.

Aligning fog lamp

- Switch fog lamps ON.

- Align Beamsetter box with fog lamp (make sure
it is between 30 and 70cm from the fog lamp
lens).

Adjust fog lamp so the top of the beam pattern aligns with the centerline
of the target grid on the beam pattern screen. - Set Beamsetter scaled wheel to 1.4%.
Pa
ge 73 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

73

Passenger's side headlight, alignment

- Move Beamsetter to the passenger side of the
vehicle and follow the same procedures to align
the Beamsetter box to the headlamp.

- Align headlight low beam, check high beam and
align fog lamp.

Note:
Make sure to reset the Beamsetter "Scaled
wheel" to the proper setting each time you
change from low beam to high beam or to fog
lamp.

- Ensure that headlights and vehicle body are
clean and free of fingerprints.
Pa
ge 74 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

74

Headlight cleaning system nozzles,
adjusting

Check setting of nozzles, adjust if necessary with
Windshield Washer Aiming Tool 3125A.

CAUTION!

To avoid damage never use a needle or
similar device to adjust nozzles.

Nozzle setting:
a = 65 mm (2.56 in.) c = 40 mm (1.57 in.)
b = 50 mm (1.97 in.) d = 90 mm (3.54 in.)
Pa
ge 75 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

94

Clock, setting

Clock is included in tachometer display. To set
time, pull out instrument panel light dimmer
switch.
When switch is pulled out briefly, hands will
advance a minute at a time. Pulled out and held,
hands will advance slowly at first, then rapidly.
Pa
ge 96 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

97

RAPGARD , paint inspection after removal
- Inspect painted surfaces under one of the
following lighting conditions:

Indoors under fluorescent lighting.
Outdoors under bright sunlight.

Important!:
If any defects on the exterior have been identified
(scratches, dings, dents and other types of body
damage):

- Contact your Service Manager and arrange to
repair defects immediately.

Note:

After removal of RAPGARD , some vehicles
may exhibit temporary paint discoloration or paint
swelling (caused by trapped moisture under the
RAPGARD ).

This temporary swelling is caused by the paint
finish absorbing moisture trapped under the
RAPGARD film.

Pa
ge 100 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6

98

Adhesive residue removal

CAUTION!

Always read and follow manufacturer
Cautions and Warnings regarding use of
product.

If RAPGARD adhesive residue remains on
paint finish, remove with a non-abrasive polishing
product such as, (3M Part No. 5995) light colors
or (3M Part No. 5996) dark colors. Thick lines of adhesive residue can be removed
with general purpose adhesive cleaner (3M Part
No. 08987-aerosol, or Part No, 08984-qt. can) or
equivalent.

Note:
Paint discoloration (looks like shaded or dark
magic marker lines) can be removed with a heat
gun using the following procedure:

- Hold heat gun approximately 3 in. away from
affected paint surfaces and apply heat using
slow oscillating motions until discoloration is
gone.

- If discoloration remains, wipe the heated area
with Isopropyl alcohol and repeat procedure to
increase surface drying.
Pa
ge 102 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6