spark AUDI A4 2017 Owners Manual
Page 301 of 386
<( a, .... N ,....
N .... 0 0
3 a,
filler door. For additional information on fu el,
r e fer to ¢
page 296.
For the tank capac ity in yo ur vehicle , refer to the
Te chn ical D ata
¢ pag e 362 .
To avoid fuel spill ing or evaporating from the fuel
tank always close fuel cap p roperly and com
p letely . An improperly closed fue l filler cap may
a lso cause the MIL lamp¢
page 25 to come on .
A WARNING -
Not paying attention when fueling or han
dling fue l incorrectly can lead to fires, exp lo
sions or serious injuries.
- Fuel ignites easily and can cause serious
burns and other injuries.
- If you do not switch the engine off when fu
eling and/or do not insert the fuel nozz le
completely into the tank opening, fue l can
leak out or run over . Leaked fuel can ignite
and start a fire .
- Do not use the telephone whi le fueling. The
electromagnetic rays can cause sparks,
wh ich can ignite fuel vapors and start a fire .
- Do not sit in your vehicle while fueling. If
you must make an except ion and enter your
vehicle again wh ile fueling , close the door
and touch meta l to discharge static electric
ity befo re touching the fue l nozzle . Static
elect ricity can create spar ks, wh ich can ig
nite vapors when fue ling.
- Do not smoke or have an open flame in the
area when fueling your veh icle or filling a
fuel contai ner because th is increases the
risk of an explosion .
- For yo ur safety , carrying f uel containers in
yo ur vehicle is no t recommended. Whethe r
f ull or empty, the conta iner can leak and
cause a fire in the event of an accident .
- If you must make an exception and trans
port a fuel container, note the following :
- Never fill the fuel container with fuel
while it is in or on the vehicle. Stat ic elec
tr icity is d ischa rged when filling wh ich can
cause the f uel vapors to ignite and in
creases the r isk of an explos ion.
- Always p lace a fuel container on the
g ro u nd before fi llin g.
Ch eck ing and Filling
-Always hold the fuel nozzle completely in
the fuel container when filling .
- If the fuel container is made of metal, the
fuel nozzle must always be in contact with
the container when filling it with fuel. This
prevents stat ic electricity from discharg
ing .
- Never spill fuel in the vehicle or the lug
gage compartment . Evaporated fuel is ex
plosive and increases the risk of serious in
jury or death .
- Follow lega l requirements when using,
stor ing and transporti ng fuel containers .
- Make sure the fuel container conforms to
industry standards (ANSI/AS TM F8S2 -86).
@ Note
- Remove spilled fuel from vehicle pa int im
mediately, because it can damage paint.
- Never drive until the fuel tank is complete ly
empty. The irregular supply of fue l that re
sults from that can cause eng ine misfires.
Uncombusted fuel will enter the exhaust
system and increase the risk of damage to
the catalytic converter .
- If the fuel tank runs complete ly empty in a
vehicle with a diesel engine , the ignition
must remain switched on fo r at least 30
seconds afte r ref ueli ng before starting the
eng ine. It may take longer than usual fo r
t he engine to s tart, even up to a minu te .
T his is because the air must first b leed out
of the fue l system when starting the eng in e.
@ For the sake of the environment
Do not overfill the fuel tank, otherwise fuel
can leak out when the vehicle is warming up.
(D Tips
D iesel ve hicles are eq uipped w ith a diesel mis
fueling guard .
It allows the vehi cle to be fu
eled on ly with a diesel fuel pump nozzle. A
worn or damaged nozzle or a nozzle that is
too small may not be able to open the diese l
misfueling guard. If this is the case, try turn
i ng the nozzle before inserting it in the fue l
filler tube, use a different fuel p ump or see an
Iii>
299
Page 315 of 386
<( a, .... N ,....
N .... 0 0
3 a,
where it will not freeze. This will prevent it
from being damaged and having to be re
placed.
Working on the battery
Be especially careful when working on or near the battery.
The battery is located in the engine compart
ment. Before you check anything in the engine
compartment,
read and heed all WARNINGS
c::>& .
Always heed the safety warnings, when wo rking
on the vehicle battery or the vehicle electrical
system to prevent injury.
The following WARNINGS are very important
when working on the battery:
Always heed the following WARNING SYM -
BOLS and safety precautions when working on
the battery.
®
Always wear eye protection.
&
Battery acid contains sulfuric acid. Al-
ways wear glov es and eye protection .
@
No
-sparks
- flames
- smoking.
~
When a battery i s charged, it produces
hydrogen gas which is explosive and
could cause personal injury.
®
Always keep the battery well out of reach
of children.
A WARNING
Whenever working on the battery or on the
electrical system, there is the risk of injury,
accident and even fire . Read and heed the fol
lowing WARNINGS:
-Always wear eye protection. Do not let bat
tery acid or any lead particles get on your
skin or clothing. Shield your eyes. Exp losive
gases can cause blindness or other injury .
- Battery acid contains su lfuric acid. Sulfuric
acid can cause blindness and severe burns.
-
Checking and Filling
-Always wear gloves and eye protection. Do
not tilt the battery because acid could leak
out of the ventilation openings.
- If you get battery acid in your eyes or on
your skin, immed iate ly r inse with cold wa
ter for several minutes and get med ical at
tent ion.
- If you shou ld ingest any battery acid, seek
med ica l attent ion immed iate ly.
- Do not expose the battery to an open flame,
electric sparks or an open light.
- Do not smoke.
- Do not interchange the positive and nega -
tive cables.
- When working on the battery, be sure not to
short-circuit the termina ls with tools or oth
er metal objects. This would cause the bat
tery to heat up very quickly, which cou ld
lead to damage or explosion and personal
injury .
- When a battery is charged, it produces hy
drogen gas which is explosive and could
cause personal injury.
- Always keep the battery well out of the
reach of children .
- Before work is done on the e lectrical sys
tem, disconnect the negat ive ground cable.
- Before performing any work on the electri
cal system, sw itch off the engine and ign i
tion as well as any electrical equipment. The
negat ive cable on the battery must be dis
connected. If you are just going to replace a light bulb, then it is enough to swi tch off
the lights.
- Before disconnecting the battery, switch off
the anti-theft alarm system! Otherwise you
will set off the alarm.
- When disconnecting the battery, first dis
connect the negative cable and then the
positive cable.
- Before reconnecting the battery, make sure
all electrical consumers are switched off.
Reconnect the positive cable first and then
the negative cable. Never interchange the
cables -this could start a fire!
313
Page 317 of 386
<( a, .... N ,....
N .... 0 0
3 a,
& WARNING
Charging a battery can be dangerous.
- Always follow the operat ing instruct ions
provided by the battery charger manufactur
er when charging your battery .
- Never charge a frozen ba ttery . It may ex
plode because of gas trapped in the ice. A l
low a frozen battery to thaw out first .
- Do not reuse batteries wh ich were frozen.
The battery housing may have cracked and
weakened when the battery froze .
- Charge the battery in a we ll ventilated area.
Keep away from open flame or electrical
spark. Do not smoke . Hydrogen gas generat
ed by the battery is exp losive.
- To reduce the danger of explosion, never
connect or disconnect charger cables whi le
the charger is operat ing.
- Fast charging a battery is dangerous and
should only be attempted by a competent
technician with the proper equipment.
- Battery acid that may spill during charging
should be washed off with a solution of
warm water and baking soda to neutralize
the acid .
(D Note
Never use a fast charger as a booster to start
the engine. This will serious ly damage sensi
tive electronic components, such as control
units, relays, radio, etc ., as well as the battery
charger .
Replacing the battery
Your veh icle is equipped with an inte llige nt ene r
gy management system for d istr ibut ing elect rici
ty ¢
page 138. The battery cha rges better in
vehicles with the en ergy management system
than in vehicles without the system. To ensure
that th e additional pow er is availabl e after re
p lac ing the battery, rep lacing w ith the same type
of b attery from the s ame manufac turer ( like the
battery that was delivered with the veh icle) is
recommended . Yo ur authorized deale r must code
the battery in the energy management system to
Ch eck ing and Filling
enable you to use the energy management func
tions corr ectly aft er replacing the batt ery .
If it is no t possib le to use a battery of this type,
the new battery mus t have the same capacity,
vo ltage ( 12-volts), amperage, construction and
plug sealing.
When install ing the battery, make sure the ig ni
t ion and all electr ica l cons umers are tu rned off.
Q) Note
- Vehicles, fo r example with a Start-Stop sys
t em*, a re equipped with a specia l cycle
proof bat tery (such as an AGM battery). In
sta lling a different type of battery can cause
prob lems in the veh icle elect rical system .
When replacing the vehicle battery, always
install one w ith the same specifications as
the origina l battery.
- Make sure that the gas venting hose is al
ways connected to the original opening on the battery s ide . Otherw ise gasses or bat
tery acid could leak out .
- Battery mounts and clamps must always be
secured correct ly .
- Read and follow the warn ings under
¢
page 313, Working on the battery before
performing any work on the battery.
® For the sake of the environment
Because of the problem of proper d isposa l of
a battery, we recommend your authori zed
Audi dealer change the battery for you. Bat
teries contain sulfur ic acid and lead and must
always be disposed of properly in compliance
wi th a ll envi ronmenta l reg ulat ions. Dispos ing
of veh icle bat teries improperly is very da nger
ous to the environment.
315
Page 358 of 386
Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engin e con be started by con
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis
charged or weak battery, the battery can be con
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in
jury. Follow the instructions below for
safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A discharged battery can freeze at tempera
tures just below 32 °F (0 °C). Before con
necting a jumper cable, you must thaw the
356
frozen battery completely, otherwise it could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion.
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial
ly different "Ah" rating may cause an explo
sion and personal injury.
- Never charge a frozen battery. Gas trapped in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen . The battery
case may have be weak
ened .
- Use of batteries of different voltage or sub
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~page 304.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
The discharged battery must be properly con-
nected to the vehicle's electrical system. .,..
Page 363 of 386
Technical data
Vehicle specifications
F ig. 281 W indshield (front left): Ve hicle Ident ification
Number (VIN)
XXXXX XX -X -XX XX X XX XX
CD+ ~t :1 :: xxxxxxxx xx x xxx xxxxx
TVP/fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~l xxxx ; xxxx xx x ; xx
11. • AUSS, I OPTIONS
E0 A
7D 5 4UB 6
XM 5SG 5R W
2E H
J0Z lL B l
A S lB A
3FC SM U 7 Xl
F 0 A 9G3 0G7 0YH 0JF
TL 6 3KA 8EH UlA X 98 Q Z7
lXW 803 908 824 020
7T6 C V7 7 K0 4 X3 2K2
3L4
4KC 3 Y 0 413
502
lSA 7GB 01 A 4G0
XX . X XX X XX X xxxx
Fig. 282 Vehicle identification label
Vehicle Identification Number (VIN) in the
Infotainment system
• Select in the Infotainment system: the I MENU I
button > left control button > Service & checks
> Vehicle information.
Vehicle Identification Number (VIN)
The VIN can be found in the Infotainment sys
tem, on the vehicle data label and under the
windshield on the driver's side*¢
fig. 281 . The
VIN is also in the right side of the luggage com
partment.
Technical data
Vehicle identification label
T he veh icle identification label¢ fig. 282 is locat
ed in the luggage compartment under the cargo
floor cover .
T he information of the veh icle identification label
can also be found in your Warranty
& Mainte
nance booklet.
The sticker contains the fol low ing vehicle data:
(D Vehicle Identification Number (VIN)
@ Vehicle type, eng ine output, transm ission
@ Engine and transmission codes
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
The safety compliance sticker is your assurance
that your new vehicle complies w ith all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu
factured. You can find this sticker on the front end of the driver's door.
It shows the month and
year of production and the vehicle identification number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR).
High voltage warning label
The high voltage warning label is located in the
engine compartment next to the engine hood re
lease. The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a sticker on the front end of
the driver's door .
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank, oil and coolant, plus maximum load, which includes
passenger weight (150 lbs/68 kg per designated
seating pos ition) and luggage weight¢,&. . .,.
361