sensor AUDI A8 1995 D2 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Repair Manual

intermittently interrupted and the sensor must
be replaced.
Pa
ge 102 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-79
Evaluation of display group 4 Display group: 4


Display field: 3
Possible malfunction cause
Corrective action
approx. -46.5 C
Open circuit or short circuit in wiring to B+ - Check wiring page 24
-79
approx. 141.0 C
Short circuit to Ground

Checking wiring

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Disconnect 4-pin connector from ECT sensor -
G62-.

- Check wiring resistance for open circuit between ECM/test box and 4-pin
ECT sensor connector.

Connector terminal 1 to ECM/test box socket 53
Connector terminal 3 to ECM/test box socket 67
Specified value: max. 1.5
Pa
ge 103 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-81
If wiring is OK:

- Check ECT sensor resistance across terminal 1 (signal) and terminal 3
(ground).
- Check measured resistance value for appropriate temperature range
using graph below (N24-0157).

Range A: 0-50 C (32-122 F)

Range B: 50-100 C (122-212 F)

Examples:
If resistance is NOT OK:
At 30 C, ECT sensor resistance should be 1500-2000 At 80 C, ECT sensor resistance should be 275-375
- Replace Engine Coolant Temperature (ECT) sensor -G62-.
- Check readiness code page 01
-70
. If Diagnostic Trouble Code
(DTC) memory has been erased, or ECM was disconnected, generate
new readiness code page 01
-73
.
Pa
ge 105 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-82

Intake Air Temperature (IAT) sensor,
checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram
Chilling spray (commercially available)
Pa
ge 106 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-84

- Compare displayed value with specified value
for intake air temperature (display field 4):

Display fields

1 2 3 4
Display group 4: General engine data
Display xxx RPM xx.xxx V
xxx.x C
xxx.x C
Indicates Engine speed
(in 40 RPM
steps) Battery Positive
Voltage (B+) Engine coolant
temperature Intake air temperature
Range 0 - 6800 RPM 0.000 - 16.500 V -46.5 to 141.0 -46.5 to 141.0
Specified
value 0 RPM 10.000 - 14.500 V --- approx. ambient temperature 1), 2)

--- --- --- Continuation page 24
-85
, Evaluation of
display group 4
1) After a long standing period (approx. 12 hours). 2) If indicated temperature deviates significantly from the ambient temperature, check IAT sensor wiring for resistance or open
circuits.
Pa
ge 108 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-85
Evaluation of display group 4 Display group: 4


Display field: 4
Possible malfunction cause
Corrective action
constant 25.5 C
Open or short circuit in wiring to B+- Check wiring page 24
-85

Short circuit to ground
approx. ambient temperature Signal intermittently interrupted
Continuation of test page 24
-87
- Check IAT sensor

Wiring, checking:

- Switch ignition off.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Disconnect 2-pin connector from Intake Air
Temperature (IAT) sensor -G42-.

- Check wiring for open circuit, between ECM/test box and 2-pin IAT harness
connector (to ECM).

Connector terminal 1 to ECM/test box socket 54
Connector terminal 2 to ECM/test box socket 67
Pa
ge 109 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-86


If wiring is OK: - Check wiring for short circuit between ECM/test box and 2-pin harness
connector according to wiring diagram.

Connector terminal 1 to vehicle Ground
Connector terminal 1 to ECM/test box socket 67
Connector terminal 1 to terminal 2
Specified value:
- Check wiring between ECM and 2-pin harness connector for short
circuit to battery B+.
Specified value: 0 volts

If resistance is NOT OK: - Check resistance across terminals of IAT sensor -G42-.

Specified value at approx. 20 C (68 F): approx. 1.5-3.5 k- Replace intake air temperature sensor -G42-.
Pa
ge 111 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-87

Continuation of test
(when IAT sensor indicates approx. ambient
temperature)

- Without disconnecting harness connector,
remove IAT sensor -G42-.

- Monitor intake air temperature value in display
field 4.

- Spray sensor with commercially available
chilling spray and check temperature value in
display field 4.

Temperature value must decrease
If NOT:

- Replace intake air temperature sensor -G42-.

- Check readiness code page 01
-70
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.
Pa
ge 112 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-88

Engine Speed (RPM) sensor, checking


Note:
Component locations page 24
-1

Required special tools and test equipment

VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Checking

- Disconnect 3-pin harness connector from engine
speed sensor.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.
Pa
ge 113 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-89


If wiring is OK: - Check wiring for open circuit between ECM/test box and 3-pin harness
connector.

Connector terminal 1 to ECM/test box socket 67
Connector terminal 2 to ECM/test box socket 63
Connector terminal 3 to ECM/test box socket 56
Specified value: max. 1.5
- Check wiring for short circuit between ECM/test box and 3-pin harness
connector, according to wiring diagram.

Connector terminal 2 to ECM/test box socket 67
Connector terminal 1 to ECM/test box socket 63
Connector terminal 1 to ECM/test box socket 56
Specified value:
- Replace engine speed (RPM) sensor -G28-.
- Check readiness code page 01
-70
. If Diagnostic Trouble Code
(DTC) memory has been erased, or ECM was disconnected, generate
new readiness code page 01
-73
.
Pa
ge 114 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1