checking AUDI A8 1996 D2 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Workshop Manual

24-16

Idle speed, checking


Notes:

Idle speed, ignition timing and CO-content
cannot be adjusted.
Idle speed is maintained by the Throttle valve
control module.
CO-content is maintained and adjusted by
Oxygen Sensor (O2S) control. Malfunctions in
O2S control are recognized by On Board
Diagnostic (OBD) and stored in DTC memory.

Required special tools and test equipment
VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
Pa
ge 21 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-18

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -1- to input display group number 1 (001),
and press -Q- button to confirm input.
System in Basic Setting 1 1 2 3 4

Indicated on display (1-4 = display fields)
Note:
After selecting function 04, the ECM initiates the following:
EVAP canister purge regulator valve is closedA/C compressor is switched of
f
- Briefly raise engine speed (acceleration burst) and let engine run at idle
for another 2 minutes.
Pa
ge 23 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-22

Heated Oxygen Sensor (HO2S) and
Oxygen Sensor (O2S) control before
TWC, checking


Notes:

Connector for Heated Oxygen Sensor (HO2S)
before Three Way Catalytic Converter (TWC) -
G39- (bank 1, sensor 1): 4-pin, black.
Connector for Heated Oxygen Sensor (HO2S) 2
before Three Way Catalytic Converter (TWC) -
G108- (Bank 2, sensor 1): 4-pin, black.
Component location page 24
-1

Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit

Pa
ge 28 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-23

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -2- to input display group number 32 (032),
and press -Q- button to confirm input.
Read Measuring Value Block 32 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 30 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-29

Checking HO2S reference voltage (Banks 1,
2)

- Disconnect 4-pin connector for respective
HO2S.

If voltage is NOT OK:
If voltage is OK: - Connect multimeter US1119 (Fluke 83 or equivalent) between harness
connector terminals 3 and 4 (to ECM), using adapter cables from
VW1594 connector test kit.
- Start engine and measure voltage.
Specified value: 0.40-0.50 volts
- Switch ignition off.
- Check HO2S wiring.

Bank 1, sensor 1 page 24
-30
.

Bank 2, sensor 1 page 24
-32
.
- Replace respective Heated Oxygen Sensor (HO2S).
Pa
ge 39 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-30

Checking HO2S wiring, bank 1, sensor 1

- Disconnect 4-pin connector (black) for HO2S -
G39-.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Check wiring for open circuit between ECM/test box and 4-pin HO2S
harness connector (to ECM).

Connector terminal 3 to ECM/test box socket 25
Connector terminal 4 to ECM/test box socket 26
Specified value: max. 1.5
- Check wiring for short circuits between terminals of 4-pin connector,
and between connector and ECM/test box.

Connector terminal 4 to ECM/test box socket 25
Specified value:
- Check wiring for short circuits to wiring harness shielding.

Connector terminal 4 to ECM/test box socket 14
Connector terminal 3 to ECM/test box socket 14
Specified value:
Pa
ge 40 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-32

Checking HO2S wiring, bank 2, sensor 1

- Disconnect 4-pin connector (black) for HO2S -
G108-.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Check wiring for open circuit between ECM/test box and 4-pin HO2S
harness connector (to ECM).

Connector terminal 3 to ECM/test box socket 39
Connector terminal 4 to ECM/test box socket 40
Specified value: max. 1.5
- Check wiring for short circuits between terminals of 4-pin connector,
and between connector and ECM/test box.

Connector terminal 4 to ECM/test box socket 39
Specified value:
- Check wiring for short circuits to wiring harness shielding.

Connector terminal 3 to ECM/test box socket 14
Connector terminal 4 to ECM/test box socket 14
Specified value:
Pa
ge 42 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-34

Oxygen Sensor (O2S) heater before
TWC, checking


Notes:

Connector for Oxygen Sensor (O2S) heater -
Z19- (bank 1, sensor 1): 4-pin, black.
Connector for Oxygen Sensor (O2S) 2 heater -
Z28- (Bank 2, sensor 1): 4-pin, black.
Component locations page 24
-1 .

Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Test requirements
Pa
ge 44 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-35

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -0- to input display group number 40 (040),
and press -Q- button to confirm input.
Read Measuring Value Block 40 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 46 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-42

Oxygen Sensor (O2S) and Oxygen
Sensor (O2S) control behind TWC,
checking


Notes:

Connector for Oxygen Sensor (O2S) behind
Three Way Catalytic Converter (TWC) -G130-
(bank 1, sensor 2): 4-pin, green
Connector for Oxygen Sensor (O2S) 2 behind
Three Way Catalytic Converter (TWC) -G131-
(bank 2, sensor 2): 4-pin, brown
Component locations page 24
-1

Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit

Pa
ge 54 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1