warning light AUDI A8 2014 User Guide

18 Instruments and warning/indicator lights
©-Engine start system
• Engine start sy stem fault. Please con­
tact dealer
If t h e in dicator light turns on and the mes­
sage appears, do
not sw itch the ignition off
be cause you may not be able to switch it on
aga in .
D rive to you r autho rized Aud i deale r immedi­
ate ly to hav e th e malfunction corrected.
11111 Engine start system fault. Please con­
tact dealer
If the indicator light t urns on and the mes ­
sage appears, there is a ma lfunction in the en­
g ine start system.
D rive to yo ur autho rize d Au di dea le r immedi­
ate ly to have t he mal function cor rected .
0 Air suspension
• Air suspension: system fault. Can cont in­
ue slowly with max. 35 mph .
There is a malfunctio n that can res ult in re­
stricted dr iving stability.
Ca re fully d rive a t a maxim um s peed o f 35
mph ( 60 km/h) to your author ized A udi dealer
or qua lified wor kshop to have the malfunction
corrected.
• Air suspension: service mode. Vehicle
can only be moved with restrictions
Ca re fully drive to your au thori zed A udi d ealer
or quali fied wor kshop immedi ate ly to have
the servi ce mode deac tiva ted.
l!IJ Air suspension fault
There is a system ma lfunction that can result
in restr icted dr iving stability or red uced
g ro und cleara nce.
Drive to yo ur authorized Aud i dealer immedi­
ately to have t he malfunction corrected .
l!IJ Air suspension: vehicle too low. Ground
clearance reduced
T he groun d clearance is very low due to a sys ­
tem malfunction. Wa it until the air suspen­
s io n system has resto red no rma l ground clear­
ance. Ot herwise, cond it ions such as an uneven
road surface can lead to vehicle damage.
tli1!.t Safety systems
T he fl (U SA models)/ El(Canada models) indi­
cator lig ht monitors the safety sys tems e .g.
airbags , p retens ione rs and illuminates fo r a
f ew seco nds ea ch time y ou swit ch t he ign ition
o n .
If th e
I (USA mod els)/ EI (Can ada models)
i ndica to r li ght does no t go o ut, or if it illum i­
n at es while yo u are d riving, o r if it start s to
blink, the n t here is a m alf u nctio n somewhe re
in the sys tem . If the ligh t does no t illumina te
whe n you switch the ig nitio n on, t his also
means there is a mal funct ion .
A WARNING ....._
If yo u have a ma lf u nction in t he safety sys­
tems, contact you r auth orized Audi dea le r
immedia tely. Othe rwise t he safety sys­
t ems may not work properly i n an acc i­
d en t.
~ Central indicator light
If th e indicato r light . or D tur ns o n, check
th e m essage in th e i nstru men t cluster.
F!,J [}; Electronic Stabilization Control
(ESC)
If the bl indicator light b links w hile d riving,
the ESC or AS R (Anti-Slip Re gulation) is active­
ly reg ulating.
If the
bl indicator light turns on , th e system
has switc hed the ESC off . In t his case, yo u can
switch the ign ition off and then on to switch
the ESC o n aga in. The ind icator lig ht tu rns off
whe n the system is functioni ng fu lly.
If the
fl indicato r light turns on, ESC was re-
stricted using the
[!I button ¢ page 199. ..,.

Instruments and warning/indicator lights 19
Stabilization control (ESC/ABS): Fault! See
owner 's manual
If the hJ indic ator lig ht and the ABS indicator
l ight ~ (USA models)
ttl] (Canada models)
turn on and the message appears, the ABS or
e lectronic differential lock is ma lfunctioning.
This a lso ca uses the ESC to malfunct ion . The
brakes st ill function with the ir normal power,
but ABS is not act ive.
Drive to your authorized Audi dea ler or quali­
f ied workshop immediately to have the mal ­
function corrected.
_& WARNING
If the 1111 (USA models)/ . (Canada
models) brake system indicator light turns
on together with the ABS and ESC indica­
tor lights, the ABS/ESC regulating function
may have failed. Functions that stabilize
th e vehicle are no longer available. This
could cause the vehicle to swerve and in­
crease the risk of sliding . Drive carefully to
the nearest a uthorized Audi dea ler or oth­
er qua lified workshop and have the mal­
function corrected.
@ Tips
For additional information on ESC and
ABS, refer to
c::> page 199 .
ABS/(8) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The warning/indicator light rJ}Il (USA mod­
e ls)
t[I] (Canada mode ls) will come on for a
few seconds when the ignition is switched on.
The light will go out after an automatic check
sequence is completed .
There is a malfunction in the ABS when :
- The warn ing/indi cator light does not illumi ­
nate when you switch the ignition on.
- T he warning/indi cator light does not go out
after a few seconds .
- T he warning/ indic ator lig ht illuminates
wh ile driving. T
he ESC indicator light also illuminates if
there is a ma lfunction in the ABS . The mes­
sage
Stabilization control (ESC/ABS) Fault!
See owner's manual
also appears in the in­
strument cluster display and a warning tone
sounds .
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more information regarding the ABS
c::>page 199.
Malfunction in the brake system
If the brake warning light c::> page 14 and the
ABS warning illum inate
together there may be
a malfunction in the ABS, and there may also
be a malfunction in the brake system itself
c::> ,&.. The ABS will not work and you will no­
tice a change in braking response and per­
formance.
In the event of a malfunction in the brake
system
the warning/indicator light 1111
(USA mode ls)/ . (Canada models) in the in­
strument cluster flashes
c::> page 14.
Malfunction in the electronic differential
lock (EDL)
The EDL works together with the ABS. The
ABS wa rning light will come on if there is a
malfunction in the EDL system
c::> page 199.
See your authorized Audi dealer as soon as
possib le .
_& WARNING
- If the~ (USA mode ls)l [i] (Canada
models) warning light does not go out,
or if it comes on while dr iving, the ABS
system is not working properly. The vehi­
cle can then be stopped only w ith the
standard brakes (without ABS). You w ill
not have the protection ABS provides.
Con tact your Audi dealer as soon as pos­
sib le.
- USA models: If the 1111 warning light,
the
hJ wa rning light and the rJ}Il wa rn­
ing light come on together, the rear

20 Instrum ent s a nd w arn in g/i ndic ato r light s
wheels co uld lock up first under hard
braking. Rear wheel lock-up can cause
loss of vehicle control and an accident.
Have your vehicle repaired immediately
by your authorized Aud i dealer or a quali­
fied workshop. Drive slowly and avoid
sudden, hard brake applications.
- Canada models: If the brake warn ing
light ., the
DJ warning light and the
ABS warning light
[iJ come on togethe r,
the rear wheels could lock up fi rst under
hard braking. Rear wheel lock-up can
cause loss of vehicle control and an acci­
dent. Have your vehicle repaired immedi­
ately by your authorized Audi dealer or a
qualified workshop. Dr ive slowly and
avo id sudden, hard brake applicat ions.
(0) Worn brake pads
EtJ Bra ke pads!
If the warn ing light illuminates, immediately
contact your authorized Audi dealer or quali­
f ied workshop to have all brake pads inspect·
ed. On USA models the warning light EtJ
comes on together with the warn ing light
1111 -Both sets of brake pads on an axle
must always be replaced at the same time.
_& WARNING
Dr iv ing with bad brakes can cause a colli­
sion and serious personal injury.
- If the wa rning light
EtJ and the wa rning
light
11111> with the message B ra ke
p ads!
comes on in the instr ument cluster
display, immediately contact your au­
thorized Aud i dealer or qualified work­
shop to have a ll brake pads checked or
replaced if necessary.
l ) - : USA models only
-
EPC Electronic power control
Applies to veh icles: w ith gasoline engine
This warning/indicator light monitors the
electronic power control .
The~ warning/indicator light (Electronic
Power Control) illuminates when you switch
the ignition on as a function check.
(D Tips
If this warning/indicator light illuminates
while you are driving, then there is a mal­
funct ion in the engine electronics. Have
the malfunct ion corrected as soon as pos­
s ible by your authorized Audi dealer or
qualified workshop.
W Glow plug system
Applies to veh icles: w ith diesel engine
The control light illuminates when the glow
plug system is active.
If the Im i ndicator light illuminates, the glow
plug system is act ive. You should start the en­
gine immediately after the ind icator light
switches off. The ind icator light only i llum i­
na tes for approximate ly 1 second if the en­
gine is warm or if the outside temperature is
above 46 QF (8 QC).
(D Tips
-If the glow plug indicator light i llum i­
nates while driving, there is an engine
contro l ma lfunction. The engine should
be checked immed iate ly .
- If the indicator light does not illuminate at a ll when switch ing the ignition on,
there may be a malfunction in the glow
plug system. The engine should be
checked.
' o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
T he symbo l
¢1111ij lights up when the ignition is .,.

Instruments and warning/indicator lights 21
switched on and will turn off after the engine
has started and has sett led at a constant idle
speed . This ind icates that the MIL is working
properly .
The warning light illuminates when there is a
malfunction in the engine e lectronic system .
Contact your author ized Audi dealer and have
the malfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢page 225.
For mo re in format ion ¢ page 29.
~. Diesel particulate filter clogged
Appl ies to vehicles: with d iesel e ngine and diese l pa rticu ­
late fi lte r
II Particulate filter : System fault See own­
er's manual
When the Ill symbol illuminates, you can al­
ter your driving style to assist the filter self­
cleaning process. Drive for approximately 15
minutes with the selector lever in the 5 posi­
tion at a minimum speed of 37 mph (60 km/
h) and an engine speed of approximately
2,000 RPM. The temperature increase that
will resu lt from this can burn off the soot in
the filter . The symbol will switch off when the
cleaning is successful. After a successful
cleaning , there is no need to bring the car to
an author ized dealer or qualified workshop
because this is part of normal vehicle ope ra­
tion .
If the symbol
&I does not switch off, see
your author ized dealer or other qualified
workshop to have the prob lem corrected.
For more informat ion on the d iesel particu­
late filter , refer to¢
page 208.
A WARNING
Always adapt your speed to the current
weather, road and traffic conditions. You
should never disobey traffic laws in order
to follow driving recommendations.
-
!'1 Engine speed limitation
App lies to veh icles: w it h e ngine speed lim itat io n
(II Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed d isplayed in the driver information
system. This protects the engine from over·
heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera­
ture range and you have re leased the accelera­
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica­
tor light
lli also turns on. Make sure that the
speed does not go above the speed disp layed.
Drive to your authorized Audi dealer immedi­
ate ly to have the malfunction corrected.
~v, Engine oil sensor
Ill Oil level! Sensor defective
If the symbol illum inates, contact your au­
thorized Audi dea le r and have the oil sensor
inspected. Until you have this done, check the
oi l level each time you refue l just to be on the
safe side¢
page 236.
Bu Fuel level indicator
Ii') Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 4 gallons (15 liters) of fuel left in the
tank. Time to refuel
q page 224.
Ii] Tank system malfunction! Contact dealer
If th e indicator light turns on and this mes­
sage appears, there is a malfunction in the
tank system.
D rive to your authorized Audi dealer immedi­
ate ly to have the malfunction corrected.
<D Windshield washer fluid level
II Please refill washer fluid

22 Instruments and warning/indicator lights
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* ¢
page 247.
~ Windshield wipers
g,.5 Windshield wiper defective
There is a malfunction with the windshield
wipers.
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
i§i l}D 10 $ Defective light bulb warning
I-If the indicator light turns on, a bulb has
failed. The message indicates the location of
the bulb.
II-if a fog lamp* has failed, the indicator
light turns on to indicate the location on the
vehicle.
a-if a rear fog lamp has failed, the indicator
light turns on to indicate the location on the
vehicle.
Vehicle lights: malfunction
If the message appears, there is a malfunc­
tion in the headlights or light switch .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
A WARNING
, -
- Light bulbs are pressurized and could ex-
plode while they are being changed caus­
ing serious personal injury.
- Work with due care when handling the
high-voltage section of gas discharge
(xenon) lights. Failure to do so could re­
sult in death or serious injury.
Have the bulb replaced or the connection
repaired by your authorized Audi Service
department.
~(D Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer working properly. Have
the system checked and repaired at your Audi
dealer.
§0 Adaptive Light
Applies to veh icles: w ith Adapt ive light
m;J Audi adaptive light: system fault
If the indicator light turns on and this mes­
sage appears, there is a malfunction in the
adaptive light system. The headlights still
function.
Go to an authorized dealership to have the
headlights or the control unit for the Adaptive
Light repaired.
@.D Light /rain sen sor
l;I Automatic headlights/automatic wipers:
system fault
If the indicator light turns on and this mes­
sage appears, the light/rain sensor is not
functioning correctly.
For safety reasons the low beams are turned
on permanently with the switch in
AUTO.
However, you can continue to turn the lights
on and off using the light switch. You can still
control all functions that are independent of
the rain sensor through the windshield wiper
lever .
Contact your authorized Audi dealer as soon
as possible to have the problem corrected.
@! Dynamic steering
l:rj Steering: system fault. you can continue
driving
If the indicator light turns on and the mes­
sage appears, the steering may be more diffi­
cult to move or more sensitive than usual. The
steering wheel may also be at an angle when driving straight. .,..

Instruments and warning/indicator lights 23
Drive s low ly to your authorized Audi dealer or
qualified workshop to have the malfunction
corrected .
,'I'M Dynamic steering: initializing
If thi s driver message appears and the indica­
tor light is flashing on the inst rument panel ,
dynamic steering is being reiniti alized . Once
you sta rt the engine after this is finished, the
steering whee l wi ll be easy to move . Re-initi­
alization might be necessary if the steering
wheel was moved hard to the left and r ight
while the veh icle was not moving. The displ ay
goes out as soon as initialization is complete .
A WARNING
-
Have the dynamic steering system mal ­
function repaired as soon as poss ible by an
authorized Audi dealer or any qualified
workshop - risk of accident!
@ Tips
-The dynamic steering stability systems
are not available in the event of a system
malfunction.
- For additional informat ion on dynamic
steering, refer to
¢page 110.
I-: Sport differential
Ill Sport differential: system fault
There is a malfunct ion with the sport differen ­
tial.
Drive to your authori zed Aud i dea ler immedi­
ately to have the malfunction corrected.
Ill Sport differential: overheating
The transmission temperature has incre ased
sign ificantly due to the sporty driving manner.
Dr ive in a less sporty manner until the tem­
pe rat ure returns to the normal range and the
indicator light switches of.
A WARNING
Contact your authorized Audi dealer or a
qualif ied workshop if the sport different ial
is faulty or malfunctioning . The repa ir
-
must be performed by trained personnel
using the correct oil in order to ensure
safety.
¢¢ Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left II or the r ight II
turn signal, the indicator light blinks. When
you use the emergency f lashers, both indica­
tor lights flash .
If one of the turn signa l light bulbs burn out,
the turn signal wi ll blink twice as fast as nor­
mal. Carefu lly drive to your authorized Audi
dealer immed iate ly to have the malfunction
corrected. The indicator light does not indi­
cate a malfunction if a turn signal on the tra il­
er or on the vehicle fails in trailer tow ing
mode .
(D Tips
For more information on the turn s ignals,
refer to¢
page 48.

24 Instruments and warning/indicator lights
Driver information
display
Overview
Fig. 4 Driver informat ion system in the instrument
cluster
Fig. S D isplay: example of th e informat ion line
The driver information system contains infor­
mation @ that is displayed on tabs @
c:;, fig. 4. The following content is possible de­
pending on vehicle equipment:
@
®
Tab Content
1 Vehicle functions :
On-board computer c::> page 25
Digital speedometer
Cruise control*
c:;, page 91
Adaptive cruise control and braking
guard*
c:;, page 94
Audi lane assist* c::> page 103
Display darkened
2 Indicator lights and messages
Warning when a door, the hood or the rear lid is not closed
c::>page29
Service interval display c::>page 28
Speed warning system ¢page 91
@ ®
Tab Content
3
Night vision assistant* c:;, page 113
4 Audio/video
s Telephone*
6 Navigation*
T he second and th ird tabs are only vis ible if at
least one indicator light or message is shown
or if that system is sw itched on.
The status line © is located in the bottom
part of the display
c::> fig. 4. It displays the ex­
terior temperature , time, selector lever posi­
t ion, trip odometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
c::> page 25 in the line (D c::> fig. 5.
_& WARNING ,___ -
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
slippery even at an outside temperature
above 41 °F
(+5 °() .
- Always remember, even if the "snow­
flake" symbol (ice warning) does not ap­
pear in the d isplay, black ice could be on
the road .
- Always reduce your speed and drive with special care in cold weather cond itions
when the chance of encountering icy
road surfaces increases.
(D Tips
-At temperatures below 14 °F (+ 5 °C) a
snowf lake symbol appears ahead of the
temperature display. It is intended to re­
m ind the driver to pay special attention
to
ice on the road c::> ,&. If the vehicle is
stationary, or if you are driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual outs ide temperature. This is .,.

Instrument s and warning /indicator lights 25
caused by the heat being radiated from
the engine.
- You can se lect the un its used fo r temper­
atu re, speed and othe r measurements in
the MML
- Fo r informa tion on the a udio/video and
navigation* functions, refer to the se pa­
r ate MMI ow ner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
gi g ~------,i
~
F ig . 6 Mult ifu nct io n stee ring wheel: operat ing t he d riv­
er informat ion system
Fi g. 7 Driver informat ion system: ope ning the ve hicle
funct io ns m en u
Operating concept
.. Switch the ign ition on.
.. To sw itch between t he tabs, press th e rocker
switch @to the left or right
c> fig . 6 .
.. To access additional informat ion be low or
above, rotat e the thumbwheel @ dow n or
up.
.. To confi rm a selection, press t he thumb­
whee l@ .
Accessing Vehicle functions
.. Sele ct the first t ab with the ro cker swit ch
@.
.. Press the b utton [jg] _ The Vehicle funct ions
menu appears c> fig . 7.
.. To select a menu item , tu rn and press t he
thumbwhee l@ .
Resetting values to ze ro
.. Select the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
men u.
.. Yo u can now select between t he long-term
memory and s hort-term memory .
.. To reset the values in a memory, p ress a nd
hold t he thumbwheel @ for one second .
The last function selected d isp lays when you
switc h the ig nition on.
On-board computer
You can ca ll up the followin g in formation in
the on -board computer:
- Date
- Dr iving t ime (h) from the shor t-te rm memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph ( km/h) from the
short-te rm memory
- Distance driven in miles (km) from the
short-te rm memory
- Cur ren t fue l consumption in MPG ( l/100
km)
- Short-term memory overview
- Long-term memory overview
T he short-te rm memory collects driv ing infor­
mation from the time the ign ition is switc hed
on until it is switched off. If you continue driv­
ing within two ho urs after switch ing the ig ni­
tion off, the new values are included when cal­
cu lating the c urrent trip information .
Un like the short -term memory, the long-term
memory is not erased automatically. You can
select the time period for evaluating t rip in­
format ion yourse lf .

26 Instruments and warning/indicator lights
For some vehicle functions, you can access the
trip information from the t emporary memory
in the line
(D ~ page 24, fig. 5.
The current fuel consumpt ion can be dis­
p layed using a bar~
page 2 7, fig. 10. The
average consumption (mpg) stored in the
short-term memory is also d isplayed. Electri ­
cal energy can be stored in the battery when
t he vehicle is coasting or driving downhill (re­
cupe rat ion) . The bar will move toward D.
Efficiency program*
The efficiency program can help you to use
less fuel. It evaluates driving information in
reference to fuel consumption and shows oth­
er equipment influencing consumption as well
as shift recommendations .
c:> page 26. Fuel
economy messages ~
page 26 provide tips
for eff icient driving . The eff ic iency program
uses distance and consumption data from trip
compute r
1.
To display the efficiency program, call up Ve­
hicle functions and select the menu option
Efficiency program .
If the data are deleted in
the efficiency program, those values are also
reset in trip computer.
@ Tips
-All stored va lues w ill be lost if the veh i­
cle battery is disconnected .
- Fuel consumptions (ave rage and cur­
r ent), range and speed are displayed in
metric units on Canadian models.
Other equipment
Applies to vehicles: with efficiency program
Fig. 8 Tri p comp uter: othe r equ ipment
Requirement: The efficiency program must be
displayed
c:> page 26 .
,. Tur n the thumbwheel unti l the other equip-
ment appears in the display.
Other equipment th at is currently affecting
fuel consumpt ion is listed in the effic iency
program. The display shows up to three other
items of equipment @. T he equipment using
the most fuel is listed first. If more than three
items using fuel are switched on, the equip­
ment that is currently using the most fuel is
displayed .
A scale @also shows the current tota l con­
sumption of all other equipment.
Fuel economy messages
Applies to vehicles: with efficiency program
Fig. 9 Display : example of a fuel econo my m essage
Fuel economy messages are displayed when
f uel consumption is increased by certa in con­
ditions. If you follow these fue l economy mes­
sages, you can reduce your vehicle's consump­
tion of fuel. The messages appear automati ­
cally and are only displayed in the efficiency
program. The fuel economy messages turn
off
automatically after a certain per iod of time .
.,. To turn an economy message
off immediate­
ly after it appears, press any button on the
multifunction steering wheel.
(D Tips
- Once you have turned a fuel economy message
off , it will only appear again af-
ter you turn the ign ition on again . .,,.

Instrument s and warning /indicator lights 2 7
-The fuel economy messages are not dis­
played in every instance, but rathe r in in­
terva ls
over a period o f time.
Cylinder on demand System
App lies to vehicles: w ith 4 .0 TFS ! engi ne
F ig. 10 Inst rume nt cluster: fuel consumption
To save fu el, the eng ine automat ic all y t urns
four cylinders o n or
off, de pending on the
amo unt of power needed. This action is not
fe lt by the passengers.
Displaying cylinder mode
Requirement: t he on-bo ard computer is di s­
pl ayed~
page 25.
~ Turn the thumbwhee l until the current fue l
c o nsu mption display is shown in the inst ru­
me nt cl uster.
If the green ba r is d ispl ayed,
yo u a re driving in 4-cylin der m ode.
Basic requirements for 4 -cylinder mode
4-cy linder drive mode is used automatically if
certain basic requir emen ts are fulfi lled. These
in clude:
- A low powe r output requi reme nt.
- Driving in third gear or higher.
- Engine speed between 960 and 3,500 RP M.
-A warm engine .
Odometer
Fig. 11 Instrument cluste r Odo meter a nd reset button
The odometer shows you how many m iles
(k ilometers) you have driven. You can switch
the d isplay from miles to kilomete rs and v ice
versa via t he MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset.
It can be used to meas­
ure s ho rt d istances . The last digit indicates
1/10 of a mile (100 meters) .
You can reset the trip odometer to zero by
pressing the Reset button~-
Lower odometer
The lower odomete r shows the tota l num ber
of m iles (kilometers) dr iven.
Malfunction message
I f th ere is a malfunc tion i n the in strumen t
cl us ter,
DEF will ap pear i n the trip odometer
display a rea. Conta ct your author ized Audi
dealer to have the problem corrected.
Time and date display
Fig . 1 2 Ce nter console: ana log clock