engine AUDI A8 2016 User Guide

.... N
0 J:
'SI: .... <J:) Lil
.... <J:) ....
authorized Audi dealer immediately to have the
malfunction corrected.
~ .... Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author­
ized Audi dealer and have the oil sensor inspect­
ed . Until you have this done, check the oil level
each time you refuel just to be on the safe s ide
¢page 224.
f Request to warm engine by driving
0 Please warm up engine
Fuel has entered the engine oil because of low
outside temperatures or frequent short drives. Drive until the engine is warm so that the fuel in
the engine oil will vaporize. Avoid high engine
speeds, full acceleration and heavy engine load
when doing this.
.Bil Fuel level indicator
ID] Please refuel
If the indicator light turns on for the first time
and the message appears, there are about 4 gal­
l ons (15 liters) of fuel left in the tank. Time to re­
fuel
¢ page 214 .
ID] Tank system malfunction! Contact dealer
If the indicator light turns on and this message
appears, there is a malfunction in the tank sys­
tem .
Drive to your authorized Audi dea ler immediately
to have the malfunction corrected.
~ Windsh ield washer fluid level
~ Please refill washer fluid
If the symbol illuminates, add windshield washer
f luid to the washer system/headlight washer sys­
tem*
¢ page 234 .
<$• Windshield wipers
m Windshield wiper defective
Instruments and indicator lights
T he re is a malfunct ion with the windshield wip­
ers .
Drive to your authorized Audi dealer immed iate ly
to have the malfunction corrected .
i§il}0/0$ Defective light bulb warning
1:1-If the indicator light turns on, a bu lb has
failed. The message indicates the location of the
bulb.
fm-if a fog lamp* has failed, the indicator light
turns on to indicate the location on the vehicle.
II-if a rea r fog lamp has failed, the indicator
light turns on to indicate the location on the vehi­
cle.
Vehicle lights: malfunction
If the message appears, there is a malfunction in
the headlights or light switch .
Drive to your authorized Audi dealer immediate ly
to have the malfunction corrected .
A WARNING
-Light bulbs are pressurized and could ex­
plode wh ile they are be ing changed causing
serious personal injury.
- Work w ith due care when handling the high­
voltage section of gas d ischarge (xenon)
lights . Failure to do so could result in death
. . . or serious inJury.
(D Tips
Have the bulb replaced or the connection re­
paired by your author ized Audi Service depart­
ment.
~{D Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer working properly . Have the
system checked and repaired at your Audi dealer.
21

Driver information
system
Overview
Fig. 4 Driver information system in the instrumen t cl uster
Fig. 5 Display : example of the information line
The driver information system contains informa­
tion @ that is displayed on tabs@¢ fig.
4. The
following content is possible depending on vehi­
cle equipment:
@
®
Tab Content
1 Vehicle function s:
On-board computer ¢page 24
Efficiency program*¢ page 25
Digital speedomete r
Cruise control*¢ page 88
Adapt ive cruise control and braking
guard* ¢page
90
Audi active lane assist*¢ page 99
Display darkened
Instruments and indicator lights
@ ®
Tab Content
2 Indicator lights and messages
Warn ing when a door, the hood or the
rear lid is not closed ¢ page 28
Service interval display ¢ page
26
Speed warning system ¢ page 88
3 Night vision assistant*¢ page 109
4 Audio/video
s Telephone*
6 Nav igation*
The second and third tabs are only visible if at
least one indicator light or message is shown or if
that system is switched on.
The status line © is located in the bottom part of
the display¢ fig.
4. It displays the exterior tem­
perature, time, selector lever position, tripod­
ometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
¢ page 25 in the line (D ¢ fig. 5.
_& WARNING
--Never rely exclusively on the outside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road
surfaces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperat ure above 41 °F (+S °C).
- Always reduce your speed and dr ive with
special care in cold weather conditions when
the chance of encountering icy road surfaces increases .
(D Tips
-You can select the units used for tempera­
ture, speed and other measurements in the
MMI.
- If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the display might be slightly high­
er than the actual outside temperature . This
is caused by the heat being radiated from
the engine .
lllJ,,
23

Unlike the short-term memory, the long-term
memory is not erased automatically. You can se­
lect the time period for evaluat ing trip informa­
tion yourself.
F or some vehicle functions, you can access driv­
ing information from the short-term memory
consecutively in the line ©~
page 23, fig. 5 by
turning the thumbwheel @.
Fuel consumption
The cu rrent fue l consumption can be shown us­
ing a bar graph¢
fig. 8. The average consump­
tion stored in the short-term memory is also dis­
p layed. If the bar is green, your vehicle is saving
fuel through one of the following functions:
- Recuperation : electrical energy can be stored in
the battery when the vehicle is coasting or driv­
ing downh ill. The bar will move toward 0.
-Cylinder on demand system*: the engine auto­
matically switches four cylinders
(4.0L TFS!) or
six cylinders (6.3L FSI) off when lower power
output is required and other conditions are met . This change is not noticeable to the pas­
sengers. The cylinders will switch on again
when higher power output is needed.
Efficiency program
Applies to: vehicles with efficiency program
Fig. 9 T rip computer: o ther equ ipment
Instruments and indicator lights
Fig. 10 Display: example of a fuel economy message
The efficiency program can help you to use less
fuel.
It shows other equipment influenci ng con­
sumption and fuel economy messages provide
tips for efficient driving. The efficiency program
uses distance and consumption data from trip
computer
1.
To display the efficiency program, call up Vehicle
functions
and select the menu option Efficiency
program.
Other equipment
Other equipment that is current ly affecting fuel
consumption is listed in the view
Consumer. The
display shows up to three other items of equ ip­
ment @¢
fig. 9. The equipment using the most
fuel is listed first. If more than three items using
fuel are switched on, the equipment t hat is cur­
rently using the most fuel is displayed.
A scale @also shows the current total consump­
tion of all other equipment .
Fuel economy messages
Fuel economy messages a re displayed when fuel
consumption is increased by certain conditions
~ fig. 10. If yo u follow these fuel economy mes­
sages, you can reduce your vehicle's consumption
of fuel. The messages appear automatically and are only displayed in the effic iency program. The
fuel economy messages turn off automatically
after a certain period of time.
To turn an economy message off immediately af­
ter it appears, press any button on the multifunc -
tion steering wheel. ..,_
25

rl
-Inspection or oil change due: If your vehicle is
due for an inspection or o il change or both, a
message appears br iefly in the instrument clus­
ter display when sw itching the ignition on or
off :
Inspection due! or Oil change due! or Oil
change and inspection duel.
Checking service intervals
The remaining distance or time to the next oil
change or to the next inspection can be viewed in
the MMI. Select the
ICARI function button > Car
systems
control button > Servicing & checks >
Service intervals .
In new vehicles or after resetting the display , the
display can be viewed after approximately
310 miles (500 km) .
Resetting the service interval display
Your authorized Audi dealer will reset the corre­
sponding service schedule after performing the
appropriate service on your veh icle . You also have
the possibility to reset the oil change schedule
after having performed an oil change according
to Audi specificat ions. Select the
ICARI funct ion
button
> Car systems control button > Servicing
& checks > Service intervals > Reset oil change
interval.
@) Note
- Only reset the oil change display when you
have completed an oil change.
- If you disconnect the battery terminals, no
calculations can be made for the service in­
terval display during this time and no serv­
ice remi nder w ill appear. Remember that
observing the proper service interva ls is v i­
tally important to extending the life of your
vehicle, particularly the engine, and main­
taining its value. Even if the mi leage driven
is low, the max imum period of one year
from one service to the next must not be ex­
ceeded .
(!') Tips
-The information in the Serv ice Reminder re­
mains stored even when the vehicle battery
~ i s disconnected .
Instruments and indicator lights
Head-up Display
Applies to: vehicles with Head-up Display
Fig. 14 Exampl e: ind ic a to rs in the Head-up Display
Fig. 15 Instrume nt panel: knob fo r th e He ad- up D isplay
The Head-up Display projects certain warnings or
selected information from the assistance sys­
tems* or navigation* on the windshield . The dis­
play appears wit hi n the driver's field of vision.
Switching on/off
.,. Press the knob~ to switch the Head-up Dis-
play on/off
c:> fig. 15 .
Adjusting the height
The height of the display can be adjusted to the
individual driver.
.,. Make sure you are sea ted correctly
i::>page 130 .
.,. Turn the knob~ to adjust the display .
Settings in the MMI
.,. Select: !CAR ! function button > (Car)* systems
control button > Driver Assist > Head-up Dis­
play
> Head-up Display content or Display
brightness.
27

Instrumen ts and ind icator ligh ts
Displ ay content
In the MMI, yo u can specify which informat ion
should be d isplayed such as navigat ion info rma­
tion* or Night vision assistant*.
The speed display and some of the red indicator
lights cannot be hidden in the MMI.
D is pl ay bri ghtness
You can adjust the disp lay brightness in the MMI.
The display brightness decreases automatically
as the amount of light decreases. The bas ic level
of br igh tness is adjusted w ith the inst rument
il ­
lum ina tion ¢ page 51.
(D Note
To prevent scratches on the g lass cove ring the
Head-up D isplay, do not place any objects in
the projection opening.
(j) Tips
- Sunglasses w ith polar izat ion fi lters and un­
favorab le lighting conditions can affect the
display.
- An optimum display depends on the seat
position and the height of the Head- up D is­
play .
- A specia l windshield is needed for the Head­
up Disp lay fu nction .
- Fo r informat ion on cleaning, refer to ¢
ta ­
ble on page
208.
Open door /hood /rear lid warning
Fig. 16 Displ ay: d oor s an d r ear lid open
With the ignition switched on , the warning illu­
m inates when a t least
one door or the hood or
28
the rear lid is not closed. The symbo l also shows
you
which door(s) or lid is not closed.
In the illustration
¢ fig . 16 it is the d river 's doo r
and the left rear door.
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL )
The Ma lfunction I ndi cator Lamp (M IU ¢.ij in the
i nstrument cluster is part of the On-Board Diag­
nostic (OBD II) system .
The wa rni ng/indicator light ill uminates when the
i gnition is sw itched on and goes out after the en ­
gine starts a nd the idle has stab ilized . This indi­
cates that the M IL is working proper ly .
If th e light do es not go out after the eng ine is
started, or illum inates while you are driving, a
malfunct ion may ex ist in the engine system. If
the light illuminates, the catalytic converte r
could b e damag ed .
Cont in ue drivi ng
with redu ced power (avoidi ng
sustai ned high speeds and/o r rapid accelera­
tions) and have the condit ion corrected . Contact
your a uthorized Audi dea ler.
If the l igh t illum inates, the electronic speed lim­
i ter may also be ma lfunctioning. For more infor­
ma tion ¢
page 29, Electronic speed Limiter .
An improperly closed fue l filler cap may also
cause the MIL light to illuminate ¢
page 214.
On-Board Diagnostics
Fig. 17 Locat io n of Data L ink Co nnecto r (DL C)

On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your eng ine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identified and the fault stored as a
code in the control module memory .
The MIL light may also illuminate if there is a leak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop ­
erly closed
¢ page 214.
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for OBD) .
In order to connect the special diagnostic equip ­
ment, push the plug into the Data Link Connector
(DLC) . The DLC is located to the right of the hood
release
c> fig . 17.
Your author ized Audi dealer or a qualified service
station can interpret the code and perform the necessary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
Your veh icle may be factory equipped with t ires
that are rated for a maximum speed of 130 mph
(2 10 km/h). This is less than the maximum speed
of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter. The electronic speed limiter prevents your vehicle from going faster
than the tir e speed rating . For more information
¢page 243 .
If the engine control unit receives faulty vehicle
road speed signals, the Malfunction Indicator
L amp
(Mil) Ill will illuminate . If this occurs,
contact the nearest authorized Audi dealer for
assistance .
Instruments and indicator lights
S8
Your vehicle 's top speed is elect ronically lim ited
to 155 mph (250 km/h).
If the engine control unit receives faulty vehicle
roadspeed signals, the Malfunction Indicator
Lamp (MIL)¢• will illuminate. If this occurs,
contact the nearest authorized Audi dealer for
assistance.
A WARNING
-A lways observe the posted speed limits and
adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires installed.
29

Opening and closing
Opening and closing
Keys
Key set
Fig. 18 Key set
@ Remote control key with mechanical key
You can centrally lock and unlock your vehicle
and start the engine w ith the master key with re­
mote control. A mechanical key is integrated in
the remote control key¢
page 31.
@ Emergency key
The emergency key is not intended for constant
use. It shou ld only be used in an emergency.
Keep it in a safe place and do not carry it on your
key ring.
Key replacement
If you lose a key , contact your authorized Audi
dealer immediately to have the
lost key disab led .
Be sure to bring all your keys with you.
Personal comfort settings
If two people use one vehicle, it is recommended
that each person always uses "their own" master
key. When the ignition is switched off or when
the vehicle is locked , personal convenience set­
tings for the following systems are stored and as­
signed to the remote master key .
- Automatic climate contro l
- Central locking system
- Rear w indow sun blind
- Amb ient lighting
- Seat memory
- Parking system*
-Adaptive cruise contro l*
30
- Audi active lane assist*
- Audi side assist*
- Audi drive select
- Night vision assistant*
- Heated steering wheel*
The stored settings are automatica lly recalled
when you unlock the vehicle, when you open the
doors or when you switch the ignition on.
A WARNING
-
- Do not leave your vehicle unattended . Al­
ways take your ignition key with you and
lock your vehicle. Entry by unauthorized per­
sons could endanger you or result in theft or
damage the vehicle.
- Do not leave children unattended in the ve­
hicle, especially with access to vehicle keys.
Ungua rded access to the keys provides chil ­
dren the opportunity to start the engine
and/or activate vehicle systems s uch as the
power windows, etc . Unsupervised opera­
tion of any veh icle system by ch ildren can
result in serious injury.
(D Tips
- The operation of the remote control key can
be temporarily disrupted by interference
from transmitters in the v icinity of the vehi­
cle working in the same frequency range
(e.g . a cell phone, radio equipment).
- For security reasons, replacement keys are
only available from Audi dealers.
- For Declaration of Compliance to United
States FCC and Industry Canada regulat ions
C?page 284.

Removing the mechanical key
Fig. 19 R emote control master key: removing the mechani·
ca l key
• Press the release button @¢fig. 19.
• Pull the mechanical key @ out of the master
key.
Using the mechan ica l key, you can:
- lock and unlock* the storage compartment on
the passenger's side¢
page 73.
- lock and unlock the vehicle manually
¢page 35.
-lock the front and rear passenger doors me­
chanically¢
page 36.
-unlock the luggage compartment lid manually
¢page 39.
Check light and battery in the master key
Fig. 20 Remote master key: Remov ing the battery holder
Check light in the ma ste r key
The check light®¢ fig. 20 in the master key
provides information about different conditions.
• The check light turns on briefly once when a
button is pressed, and during an "inquiry" by
the conven ience key system.
Open ing and closing
• If the check light does not come on, the battery
is dead and has to be replaced. In addition,
when the battery is dead the
!I ind icator light
appears in the instrument cluster display as
well as the message
Please change the key
battery .
Ma ster key battery replacement
• Remove the mechanical key ¢page 31.
• Press the re lease button @¢ fig. 20 on the
battery holder and at the same time pull the
battery holder out of the master key in the di­
rection of the arrow .
.. Install the new batte ry CR 2032 with the"+"
sign facing down.
.. Push the battery holder carefully into the mas­
ter key .
.. Insta ll the mechanical key .
@ For the sake of the environment
Dispose of dead batteries properly so as not
to pol lute the environment.
(D Tips
The replacement battery must be the same
specification as the original.
Electronic immobilizer
The immobilizer helps to prevent unauthorized
use of your vehicle.
A computer ch ip inside your key automatically
deact ivates the electronic immob ilizer when the
key is inside the vehicle. When you remove the
key from the vehicle, the elect ronic immob ilizer
is automatically activated once again .
& WARNING
-
Always take the key with you when you leave
the vehicle. The key can disarm the electronic
engine immobilizer and permit an unauthor­
i zed person to start the engine and enable op­
eration of the vehicle systems such as power
window or power sunroof leading to serious
personal injury.
31

Opening and clo sin g
• Press button@ to unlock the vehicle¢ fig. 21.
• Press button ffl to lock the vehicle ¢ A in Gen­
eral description on page 32 .
• Press button C:$ briefly to unlock the luggage
compartment lid.
• Push the red
I PANIC I button to activate the
panic funct ion . The horn sounds and the turn
s ignals flash. Push the red
! PANIC I button again
to deactivate the pan ic function .
If the vehicle is unlocked and no door, the lug­
gage compartment lid or the hood is opened
with in 60 seconds, the vehicle locks itself agai n
automatically. This feature prevents the vehicle
from being accidentally left unlocked over a long
period of time.
It depends o n the settings in the MMI whethe r
the entire veh icle is unlocked or only certa in
doors¢
page 33 .
& WARNING
Read and follow all WARN INGS ¢ & in Gener­
al description on page 32 .
@ Tips
-In orde r to make s ure the locking function is
working, you s hou ld always keep your eye
on the vehicle to make sure it is properly
l ocked.
- Do not use the remote contro l if you are in­
side the car, otherwise you may uninten ­
tiona lly lock the vehicle, and then yo u wou ld
set off the anti-theft alarm when you try to
start the engine or open a door. In case this happens anyhow, push the unlock button@.
- The vehicle can only be locked when these­ lector lever is in the P position.
- Use the panic funct ion only if you are in an
emergency s ituation.
34 Locking and unlocking with convenience
key
Applies to:
vehicles with convenience key
The doors and the luggage compartment lid can
be unlocked and locked without operating the
master key.
Fig. 22 Co nve nience key : locking t he ve hicle
Unlocking vehicle
• Take hold of the door hand le . The door is un-
locked automatically.
• Pull the handle to open the door .
Locking vehicle
• Sele ct the P selector lever positio n. Otherwise
the vehicle cannot be locked .
• To lock the vehicle, close the door and touch
the sensor in the door handle
once ¢ fig. 22. Do
not reach inside the door handle .
The vehicle can be locked and unlocked at any
door. The master key must be within a range of
about 1.5 m from the appropriate door or the
l uggage compartment lid. It makes no difference
whether the maste r key is in your jacket pocket or
i n your brief case .
It is not possib le to re-open the door for a brief
per iod direct ly after closing it . Th is allows you to
ensure that the doors are properly locked .
It depends on the settings in the MMI whether
the entire vehicle is unlocked or one of the doors
¢ page 33 .
& WARNING
Read and follow all WARNINGS ¢ & in Gener­
al description on page 32 .

-The buttons for the power sun shades * in the
side windows.
- The button for the front passenger's seat ad­
justment*.
A WARNING 1=
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren rema in in the vehicle . Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows. The power windows a re functional un­
ti l the driver's door or passenge r's door has
been opened.
- Pay ca reful attention when closing the win­
dows.
It could cause injury by pinching.
- When locking the veh icle from outside, the
vehicle must be unoccupied since the win­ dows can no longer be opened in an emer­
gency.
@ Tips
- Using the switches © and @, the driver can
also operate the power sunshades* in the
side windows.
- After tu rning the ignition off you can st ill
open and close the w indows for app roxi ­
ma tely 10 minutes. The powe r windows are
not switched off until the driver's door or
passenger's door has been opened.
What to do after a malfunction
-
The one -touch open and close function must be
reactivated if the battery has been disconnected .
.,. Pull and hold the power w indow switch unt il
the window is fully closed.
.,. Release the switch and then pull it again for at
least one second.
Openin g an d clos ing
Valet parking
The valet parking feature protects the luggage
compartment from unauthorized access.
Fig. 36 Valet parking button
With "valet parking" act ivated, the luggage com­
partment lid cannot be opened .
.,. Remove the mechanical key
c::> page 31.
.,. Open the glove compartment and activate
c::> fig. 36 the "valet parking" feature by press­
ing the
!VA LE T I button. The indicator light in
the switch illumina tes.
.,. Close the glove compartment and lock it with
the mechanical key.
.,. Leave the master key with the service personnel
for parking and keep the mechanical key with
you .
When the "valet parking" feature is activated:
- the unlocking button fo r the luggage compart­
ment lid~ in the driver's door is inactive
- the button~ on the master key is inactive
- the opening handle in the luggage compart-
ment lid is inactive.
The vehicle can be driven and locked and un­
locked with the master key . Access to the lug­
gage compartment is b locked.
When the valet parking function is switched on,
the message
V ale t p arki ng activat ed appears in
the instrument cluster d isp lay when you switch
the ignition on.
4 1