window AUDI A8 2016 Owner's Manual

-Never place or install floor mats or other
floor coverings on top of already installed
floor mats. Additional floor mats and other
coverings will reduce the size of the pedal
area and interfere with the pedals .
- Always properly reinstall and secure floor
mats that have been taken out for cleaning.
- Always make sure that objects cannot fall
into the driver footwell while the vehicle is
moving . Objects can become trapped under
the brake pedal and accelerator pedal caus­ ing a loss of veh icle control.
Storing cargo correctly
Loading the luggage compartment
All luggage and other objects must be properly
stowed and secured in the luggage compart­
ment.
L oose items in the luggage compartment can
shift suddenly, changing vehicle handling charac­
teristics. Loose items can also increase the risk of
serious personal injury in a sudden vehicle ma­
neuver or in a collision.
.. Distribute the load evenly in the luggage com­
partment.
.. Always place and properly secure heavy items in
the luggage compartment as far forward as
possible.
.,. Secure luggage items using the tie-downs pro­
vided
¢ page 68, Luggage compartment .
A WARNING
Improperly stored luggage or other items can
fly through the vehicle causing serious per­
sonal injury in the event of hard braking or an
accident. To help reduce the risk of serious
personal injury:
- Always put objects, for example, luggage or
other heavy items in the luggage compart­
ment.
- Always secure objects in the luggage com­
partment using the tie-down hooks and
suitable straps .
Driving safety
A WARNING
Heavy loads will influence the way your vehi­
cle handles. To help reduce the risk of a loss
of control lead ing to serious personal injury:
- Always keep in m ind when transporting
heavy objects, that a change in the center of
gravity can also cause changes in vehicle handling:
- Always distribute the load as evenly as
possible .
- Place heavy objects as far forward in the
luggage compartment as possible.
- Never exceed the Gross Axle Weight Rating
or the Gross Vehicle Weight Rating specified
on the safety compliance sticker on the left
door jamb. Exceeding permissible weight
standards can cause the vehicle to slide and handle differently.
- Please observe information on safe driving
¢page 129.
A WARNING
To help prevent poisonous exhaust gas from
being drawn into the vehicle, always keep the
rear lid closed while driving .
- Never transport objects larger than those
f itting completely into the luggage area be­
cause the rear lid cannot be fully closed.
- If you absolutely must drive with the rear lid open, observe the following notes to reduce
the risk of poisoning:
- Close all windows,
- Close the power roof,
- Open all air outlets in the instrument pan-
el,
- Switch off the air recirculation
,
- Set the fresh air fan to the highest speed .
A WARNING
Always make sure that the doors, all win­
dows, the power roof and the rear lid are se­
curely closed and locked to reduce the r isk of
in jury when the vehicle is not being used.
- After closing the rear lid, always make sure
that it is properly closed and locked.
-
135

Driving safety
-Never leave your vehicle unattended espe­
cially with the rear lid left open. A child
could crawl into the vehicle through the lug­
gage compartment and close the rear lid be­
coming trapped and unable to get out . Be­
ing trapped in a vehicle can lead to serious
personal injury.
- Never let children play in or around the vehi­
cle.
- Never let passengers ride in the luggage compartment. Vehicle occupants must al­
ways be properly restrained in one of the ve­
hicle's seating positions.
- Air circulation helps to reduce window fog­
ging . Stale air escapes to the outside
through vents in the trim panel, on the left
side of the luggage compartment. Be sure
to keep these slots free and open.
- The tire pressure must correspond to the
load. The tire pressure is shown on the tire
pressure label. The tire pressure label is lo­
cated on the driver's side B·pillar. The tire pressure label lists the recommended cold
tire inflation pressures for the vehicle at its
maximum capacity weight and the tires that
were on your vehicle at the time it was man­
ufactured. For recommended tire pressures
for normal load conditions, please see chap­
ter ¢
page 247.
Tie-downs
The luggage compartment is equipped with four
tie-downs to secure luggage and other items .
Use the tie-dow ns to secure your cargo properly
¢ page 135, Loading the luggage compartment .
In a coll ision, the laws of physics mean that even
smaller items that are loose in the vehicle will
become heavy missiles that can cause serious in­
jury . Items in the vehicle possess energy which
vary with vehicle speed and the weight of the item. Vehicle speed is the most significant factor.
For example, in a frontal collision at a speed of
30 mph (48 km/h), the forces acting on a 10 -lb
(4 .5 kg) object are about 20 times the normal
136
weight of the item. This means that the weight
of the item would suddenly be about
200 lbs. (90 kg) . You can imagine the injuries
that a 200 lbs. (90 kg) item flying freely through
the passenger compartment could cause in a col­
lision like th is.
A WARNING
Weak, damaged or improper straps used to
secure items to tie-downs can fail during hard
braking or in a collision and cause serious per­
sonal injury.
- Always use suitable mounting straps and
properly secure items to the tie-downs in
the luggage compartment to help prevent items from shifting or flying forward as dan­
gerous missiles.
- Never attach a child safety seat tether strap
to a tie-down.
-
Reporting Safety Defects
Applicable to U.S.A.
If you believe that your vehicle
has a defect which could cause a
crash or could cause injury or
death, you should immediately in­
form the National Highway Traffic Safety Administration (NHTSA) in
addition to notifying Audi of
America, Inc.
If NHTSA receives similar com­plaints, it may open an investiga­
tion, and if it finds that a safety
defects exists in a group of
vehicles, it may order a recall and remedy campaign. However,
NHTSA cannot become involved in
individual problems between you,
11>

A WARNING
Not wearing safety belts or wearing them im­
properly increases the risk of serious personal
injury and death . Safety belts can work only
when used correct ly.
-Always fasten your safety belts correctly be­ fore driving off and make sure all passen­
gers are cor rect ly restrained.
- For maximum protection, safety belts must
always be posit ioned properly on the body .
- Never strap more than one person, includ­
ing small ch ildren, into any belt .
- Never place a safety belt over a child sitting
on your lap.
- Always keep feet in the footwell in front of
the seat wh ile the vehicle is being driven.
- Never let any person ride w ith their feet on
the instrument panel or sticking out the
window or on the seat .
- Never remove a safety belt while the vehicle
is moving . Do ing so will increase your risk of
being injured or k illed.
- Never wear belts twisted.
- Never wear belts over rigid or breakable ob-
jects in or on your clothing, such as eye
glasses, pens, keys, etc., as these may cause
injury.
- Never allow safety belts to become dam­
aged by being caught in door or seat hard­
ware.
- Do not wear the shoulder part of the belt
under your arm or otherwise out of position .
- Several layers of heavy clothing may inter­
fere with correct positioning of belts and re­
duce the overall effectiveness of the system.
- Always keep belt buckles free of anything
that may prevent the buckle from latching
securely .
- Never use comfort clips or devices that cre­
ate slack in the shoulder be lt . However, spe­
cial clips may be requ ired for the proper use
of some child restraint systems.
- Torn or frayed safety belts can tear, and
damaged belt ha rdware can break in an acc i­
dent. Inspect belts regularly.
If webbing,
bind ings, buckles, or re tractors are dam-
Safet y bel ts
aged, have belts rep laced by an authorized
Aud i dea ler or qualified workshop.
- Safety belts that have been worn and loaded
in an accident must be replaced with the
correct replacement safety belt by an au­
thor ized Audi dealer. Replacement may be
necessary even if damage cannot be clearly
seen. Anchorages that were loaded must al­
so be inspected.
- Never remove, mod ify, d isassemble, or try
to repair the safety belts yourse lf.
-Always keep the belts clean . Dirty belts may
not work properly and can impair the func­
tion of the inert ia reel~
table Cleaning inte­
rior on page 208 .
Safety belts
Fastening safety belts
Safety first -everybody buckle up!
Fig. 159 Be lt buckle and tongue on the driver 's seat
To provide maximum protect ion, safety belts
must always be positioned correctly on the wear­
er's body .
.. Adjust the front seat and head restraint proper­
ly¢
page 58, General information.
.. Hold the belt by the tongue and pull it evenly
across the chest and pelvis
¢ /J:::.. .
.. Insert the tongue into the correct buckle of
your seat unt il yo u hear i t latch secu rely
¢ fig. 159 .
.. Pull on the belt to make sure that it is secure ly
latched in the buckle.
Automatic safety belt retra ctors
E ve ry safety belt is equipped with an automatic
belt ret ractor on the shoulder belt. This feat ure .,..
141

Airbag syste m
How supplemental side airbags work
Side airbags deploy instantly and can help re­
duce the risk of upper torso injuries for occu­
pants who are properly restrained .
Fig . 1 70 In fla ted side airbags o n lef t s ide of vehicle , rear
side a irbag
When the system is triggered, the a irbag is filled
with propellant gas and breaks through a seam in
the seat surface area ma rked "AIRBAG". It ex ­
pands between the side trim pane l and the pas­
senger. In order to help provide th is additiona l
protection, the side ai rbag must inflate within a
fraction of a second at very h igh speed and with
great force . The supplementa l side airbag could
injure you if your seating position is not proper or
upright or if items are located in the area where
the supplemental side airbag expands . This ap ­
plies especially to children
~ page 168, Child
safety .
Supplemental side a irbags inflate be­
tween the occupant and the door pane l on the
side of the vehicle that is struck in certa in side
coll is ion
~ fig. 170.
A lthough they are not a soft pillow, they can
"cushion" the impact and in th is way they can
help to reduce the risk of injury to the uppe r part
of the body .
A fine dust may develop when the airbag deploys .
This is normal and does not mean there is a fire
in the vehicle .
164
Important safety instructions on the side
airbag system
Airbags are only supplemental restraints . Always
properly wear safety belts and ride in a proper
seating position .
There is a lot that you and your passengers must
k now and act according ly to help the safety belts
and airbags do their job to prov ide supplemental
protect ion .
_& WARNING
An inflating side airbag can cause serious or
fatal injury. Improperly wearing safety be lts
and improper seating posit ions increase the
risk of serious persona l injury and death
whenever a vehicle is being used.
- In order to reduce the risk of injury when
the supplemental side airbag inflates:
- Always s it in an upr ight position and never
l ean agains t the area where the supple­
mental s ide airbag is located .
- Never let a child or anyo ne e lse rest their
head against the side tr im panel in the
area where the s upplementa l side airbag
inflates .
- Always make s ure t hat safety belts are
worn correctly,
- Do no t let anyone s itting in the front seat
p ut their hand or any other parts of their
body out of the window.
- Always make sure that the side a irbag can
inflate w ithout interference.
- Never install seat covers or replacement
upholstery over the front seatbacks that
have not bee n specifical ly approved by
A udi .
- Never use additional seat cushions that
cover the areas where the side airbags de­ ploy.
- Damage to the orig inal seat cove rs or to
the seam in the area of the s ide airbag
module must a lways be repaired immedi­
ate ly by an autho rized Aud i dealer .
-
-Objects between you and the a irbag can in­
crease the r isk of injury in an acc iden t by in­
t erfering wi th the way the airbag unfolds or
~

Airbag system
the circumstances will vary considerably between
one collision and another. Important factors in­
clude, for example, the nature (hard or soft) of
the impacting object, the angle of impact, vehicle
speed, etc.
c:;, page 166, How side curtain air­
bags work .
Aside from their normal safety function, safety
belts work to help keep the driver or front pas­
senger in position in the event of a collision so
that the side curtain airbags can provide protec ­
tion .
The airbag system is not a substitute for your safety belt. Rather, it is part of the overall occu­
pant restraint system in your vehicle . Always re ­
member that the airbag system can only help to
protect you if you a re wearing your safety belt
and wearing it properly . This is another reason
why you should always wear your safety belts,
not just because the law requires you to do so
c:;, page 138, General information.
It is important to remember that whi le the s ide
curtain airbag system is designed to help reduce
the likelihood of serious injuries, other injuries,
for example, swelling, bruising, and minor abra ­
s ions can a lso be associated with these airbags
upon deployment. Remember too, these a irbags
will deploy only once and only in certa in kinds of
accidents - your safety belts are always there to
offer protect ion .
The side curtain airbag system ba sically
consists of:
-The electronic control module and external side
impact sensors
- The side curtain airbags above the front and
rear side windows
- The airbag indicator light in the instrument
panel
The airbag system is monitored electronically to make certain it is functioning properly at all
times. Each time you switch on the ignition, the
airbag system indicator light will come on for a
few seconds (self diagnostics) .
The side curtain airbag is not activated:
-if the ignition is switched off,
166
- in side collisions when the acceleration meas­
ured by the sensor is too low,
- in rear-end collisions.
A WARNING
-Safety belts and the airbag system will only
provide protection when occupants are in
the proper seating position
c:;, page 58, Gen­
eral information .
-If the airbag ind icator light c:;, page 18
comes when the vehicle is being used, have
the system inspected immediately by your
author ized Audi dealer. It is possible that
the airbag will inflate when it is not sup­
posed to, or wi ll not inflate when it should.
How side curtain airbags work
Side curtain airbags can work together with side
airbags to help reduce the risk of head and upper
torso injuries for occupants who are properly re­
strained.
Fig. 172 Illus trat io n of princ iple: I nflated s ide c urtain a ir­
bags o n the left side
The side curtain airbags inflate between the oc­
cupant and the windows in a side collision
¢ fig. 172.
When the system is triggered, the side curta in
airbag is filled w ith propellant gas and breaks
through a seam above t he front and rear side
windows identified by the AIRBAG label. In order
to help provide this additional protection, the
s ide curtain airbag must inflate within the blink
of an eye at very high speed and with g reat fo rce.
The side curtain airbag could injure you if your
seat ing position is not proper or upright or if

Child safety
and the installation of child restraint sys­
tems
r::> page 168 , Child safety.
(D Note
On vehicles with power adjustable rear seats*
some criteria must be observed when attach­
ing the child restraint using the
LA TCH sys ­
tem:
- To attach the chi ld restraint securely, the
seat must be moved to the farthest rear po­
sition, the seat height set to the lowest po­
sition and the head restraint must be ad­
justed to the vertical position
c'.:> page 61.
- If a ch ild safety seat is attached to one of
the rear seats , this seat must not be adjust­
ed using the power controls under any cir ­
cumstances . The
Entr y ass is ta n ce for th is
seat must also be deactivated in the MMI
r::> page 64. The child safety seat as wel l as
the rear seat can be damaged by the adjust­ ment process .
Tether anchors and tether straps
Fig. 18 4 Te ther a nch ors: recess flaps beh ind the rear sea t­
ba cks
The tether anchors for the two* /three rear seat­
ing positions are located in recesses in the rear
window shelf
r::> fig . 184 . Vehicles with two rear
seating positions* are equ ipped w ith two tether
anchors .
A tether is a straight or V-shaped strap that at­ taches the top part of a child restraint to special
anchorage points in the vehicle .
The purpose of the tether is to reduce the for­
ward movement of the child restraint in a crash, in order to help reduce the risk of head injury
184
that cou ld be caused by striking the vehicle inte­
r ior.
Forward facing child restra ints manufact ured af­
ter September 1, 1999, a re required by U.S. fed­
eral regu lations to comply with new child head
movement performance requirements . These
new performance requ irements make a tether
necessary on most new child safety seats.
A WARNING
Improper installation of child restraints wi ll
i ncrease the risk of injury and death in a
crash .
- Always follow the instructions provided by
the manufacturer of the ch ild restraint you
intend to install in your Audi .
- Improper use of chi ld restraint anchors (in­
cluding tether anchors) can lead to injury in
a co llision. The anchors are designed to
w ithsta nd only those loads imposed by cor­
rectly fitted ch ild restraints.
- Never mo unt two ch ild rest raint systems on
one LATC H lower anchor poin t.
- Never attach two child restraint systems to
one tether st rap or tethe r anchorage.
- Never attach a tether strap to a tie-down
hook in the luggage compa rtment .
- Never use child restra int tether anchorages
to secure safety belts or other kinds of occu­
pant restraints.
- Never secure or attach any luggage o r other
items to the LATCH lowe r anchorages or to
the te ther anchors.
- I f a tether or other strap is used to attach a
child restra int to the front passenge r seat,
make sure that it is not so tight, tha t it
causes the weight-sensing mat to meas ure
more weight than is actually on the seat.
- The heavier weight reg istered can make the
Advanced A irbag Sys tem wor k as though a n
adu lt were on the seat and deploy the Ad ­
vanced Airbag when it must be suppressed
causing serious or even fatal injury to the
child.
- If you must insta ll a rearward facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the

Audi pre sense Preventative passenger
protection
A ppl ies to: ve hicles with Audi pre se nse
Audi pre sense can initiate steps to help protect
vehicle occupants in certain situations. The func­
tions described depend on equipment installed in
your veh icle:
Audi pre sense basic
The following functions can be triggered in cer­
tain driving situations:
- Tightening of the safety belts (for examp le,
during heavy braking): the front safety belts
have reversible belt pretensione rs. If a collision
does not occur, the safety belts loosen slightly
and are ready to be t ightened again.
- Closing the windows and the sunroof*: the win­
dows and the sunroof* close leaving a small
open gap .
Audi pre sense basic functions can be triggered at
speeds above 20 mph (30 km/h). The deploy­ ment time is adapted in the drive select mode dy­
namic.
Audi pre sense front (vehicles with adaptive
cruise control*)
Audi pre sense front includes the functions in
Audi pre sense basic . In addition, within the lim ­
its of the system, the likelihood of a collision
with the vehicle immediately ahead is also calcu­ lated.
If the system senses an imminent collision
the following functions can be triggered:
- Braking guard
~ page 96
- Tightening the safety belts
- Closing the windows and the sunroof* (leaving
a small open gap)
Audi pre sense rear (vehicles with Audi side
assist*}
Audi pre sense rear includes the functions in Audi
pre sense basic. In addition, the likelihood of a
rear-end collision with the vehicle coming from
behind is also calculated.
If the risk of a collision
is detected , the following functions can be trig­
gered:
Audi pre sense
-Tig htening the safety belts
- Closing the windows and the sunroof* ( leaving
a small open gap)
- Adjusting the seats: the settings for the power
head restrains, the upper sections of the backr­
ests and the pneumatic side bolsters* are opti­ mized for the front seats and the outboard rear
seats*. If a co llision does not occur, the previ­
ous seat settings are restored.
Audi pre sense plus
Audi pre sense plus includes the functions in Audi
pre sense front and Audi pre sense rear.
Error message
Audi pre sense: not available
Preventative passenger protection is not availa­
ble . See your authorized Audi dealer immediately
to have the malfunction corrected .
A WARNING
-
Audi pre sense cannot overcome the laws of
physics. It cannot prevent a collision. Do not
l et the increased safety provided tempt you to
take risks. This will increase the risk of a colli­
sion and serious personal injuries.
- The sensors cannot always detect all ob­
jects. This increases the risk of a collision.
-Audi pre sense does not detect people or an­
imals or objects that are crossing the vehi­
cle's path
~ page 90.
-The radar sensor's vision can be reduced by
heavy rain, ice, snow, heavy road sp ray and
reflections from guard rails, tunne l entran­
ces, etc. These and similar conditions can prevent vehicles from being accurately de­
tected and in some cases they may not be
detected at all.
(D Note
The sensors can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. This can affect the function of the
Audi pre sense system . Have your authorized
Audi dealer check to make sure that the sys­
tem is work ing properly.
187

Smart Technology
ignition switched off, it controls the energy sup­
p ly to the various electrical components. Data
from battery diagnosis is considered.
Depending on the battery's state of charge, indi­
vidual consumers are gradually turned off to pre ­
vent excessive discharge of the battery and thus maintain starting capability.
Dynamic energy management
While the vehicle is being driven, dynamic energy
management distributes the energy generated
according to the needs of the individual compo­
nents.
It regu lates consumption, so that more
electrical energy is not being used than is being
generated and ensures an optimal state of
charge for the battery.
(D Tips
- But even energy management cannot neg­
ate the limits of physics . Cons ider that the
power and life of a battery are limited.
- If starting ability is threatened, the indica­
tor light (•) appears
9 page 15, Cl Battery.
What you should know
The highest priority is given to maintaining start­
ing capability .
The battery is severely taxed in short-distance
driving, in city traffic and during the cold time of
year. Abundant electrical energy is required, but
only a little is generated . It is also crit ica l if the
engine is not running and electrical components
are turned on . In this instance energy is be ing
consumed but none is being generated .
It is in precisely these situations that you will no­
tice energy management actively regulat ing the
d istr ibut ion of energy .
Vehicle stands for an extended period
If you do not driv e your vehicle over a period of
several days or weeks, electrical components are
gradually cut back or switched off. This reduces
energy consumption and ma inta ins starting ca­
pability over a longer period . Some of the con­
ven ience funct ions may not operate, such as the
interior l ights or the power seat adjustment. The
196
convenience functions will be availab le again
when you switch on the ignition and start the en­ gine.
With the engine turned off
If you listen to the radio, for example, with the
engine turned off or use other MMI funct ions,
the battery is being d ischarged .
If starting capab ility is jeopardized due to energy
consumption, a message appears in the MMI dis­
play .
The message indicates that the system will be
switched off automat ically in a moment . If you
wish to cont inue using the functions, you have to
start the engine.
With the engine running
Although electrica l energy is generated when the
vehicle is being driven, the battery can become
discharged. This happens mostly when little en­
ergy is being generated and a great deal con ­
sumed and the battery's state of charge is not
opt imal.
To bring the energy balance back into equilibr i­
um, consumers wh ich require espec ially large
amounts of energy are temporarily cut back or
switched off. Heating systems in particular re­
quire a great dea l of energy. If you notice , fo r ex­
amp le, that the heated seats* or the heated rear
window are not heating, they have been tempo­
rarily cut back or switched off. These systems will
be available aga in as soon as the energy balance
has been restored.
You will also notice that engine idle speed has
been increased slig htly. This is norma l and not a
cause for concern . By increasing engine idle
speed the additional energy required is generat­
ed and the battery is charged.

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from your authorized Audi dealer or a
qualified workshop. Read and follow the instruc­
tions for use on the packaging.
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi­
soning.
@ For the sake of the environment
- Preferably use environmentally-friendly
products when buying cleaning agents.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer deposits remain on the vehicle, the
more the surface can be damaged. High temper­
atures such as those caused by sunlight increase
the damaging effects .
Before washing, wet heavy deposits with plenty
of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
Also, wash the underside of your vehicle once
road salt stops being used for the season.
Pressure washers
When washing your vehicles with a pressure
washer, always follow the operating instructions
provided with the pressure washer. This is espe­
cially important in regard to the pressure and
spraying distance . Do not aim the spray directly
at seals on side windows, doors, the hood, the
206
rear lid or the sunroof* or at tires, rubber hoses,
insulating material, sensors* or camera lenses*.
Keep a distance of at least 16 inches (40 cm) .
Do not remove snow and ice with a pressure
washer.
Never use rotary nozzles or high pressure noz­
zles.
The water temperature must not be above 140 °F
(60 °C).
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are
off . Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Only use car washes where the vehicle remains
stationary and the washing equipment moves
around the vehicle when washing and drying. Car
washes that move the vehicle through the car
wash using a chain are not recommended.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint.
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro­
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a sham my. ..,..

Care and cleaning Component Situation Solution
Decorative parts/
Dirty Mild soap solutiona>, a cleaning solution suitable for stain-
trim less steel, if necessary
Paint Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint
¢page 277
Spilled fuel Rinse with water immediately
Rust film Rust film remover, then protect
with hard wax; for ques-
tions, refer to an authorized Audi dealer or a qualified
workshop
Corros ion Have it removed by an authorized Aud i dea ler or a qua lified
wo rkshop
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean pa int
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in-Dampen with water immediately and remove w ith a micro-
sects, bird droppings, fiber cloth
tree sap and road salt
grease-based con- Remove immediately with a m ild soap solutiona> and a soft
taminants such as cloth
cosmetics or sunblock
Carbon parts Dirty Clean the same way as painted parts¢ page 206, Car
washes
a l Mild soap so lution: maxim um two tablespoo ns neu tra l soap in 1 quar t Cl lite r) of water
Cleaning interior
Component Situation Solution
Windows
Dirty Glass cleaner, then wipe dry
Decorative parts/ Dirty Mild soap so lutiona>
trim
Plastic parts
Dirty Damp cloth
Heavily soiled Mild soap solutiona>, solvent-free p lastic clean ing solution,
if necessary
Displays Dirty Soft cloth with LCD cleaner
Controls Dirty Soft brush, then a soft cloth with a m ild soap solutiona >
Safety belts Dirty Mild
soap solutiona>, allow to dry before letting them re-
tract
208
...